Prepare for 2.6.22.1 kernel
Prepare for 2.6.22.1 kernel



git-svn-id: svn://svn.openwrt.org/openwrt/trunk@8212 3c298f89-4303-0410-b956-a3cf2f4a3e73

--- a/target/linux/at91-2.6/Makefile
+++ b/target/linux/at91-2.6/Makefile
@@ -11,7 +11,8 @@
 BOARDNAME:=AT91
 FEATURES:=squashfs usb
 
-LINUX_VERSION:=2.6.21.5
+#LINUX_VERSION:=2.6.21.5
+LINUX_VERSION:=2.6.22.1
 
 define Target/Description
   Build fimware images for Figment Design Labs VersaLink board.

--- a/target/linux/at91-2.6/config/default
+++ b/target/linux/at91-2.6/config/default
@@ -11,6 +11,7 @@
 # CONFIG_ARCH_CLPS711X is not set
 # CONFIG_ARCH_CLPS7500 is not set
 # CONFIG_ARCH_CO285 is not set
+# CONFIG_ARCH_DAVINCI is not set
 # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
 # CONFIG_ARCH_EBSA110 is not set
 # CONFIG_ARCH_EP93XX is not set
@@ -26,6 +27,7 @@
 # CONFIG_ARCH_IXP2000 is not set
 # CONFIG_ARCH_IXP23XX is not set
 # CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_KS8695 is not set
 # CONFIG_ARCH_L7200 is not set
 # CONFIG_ARCH_LH7A40X is not set
 # CONFIG_ARCH_NETX is not set
@@ -38,6 +40,7 @@
 # CONFIG_ARCH_S3C2410 is not set
 # CONFIG_ARCH_SA1100 is not set
 # CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
 # CONFIG_ARCH_VERSATILE is not set
 CONFIG_ARM=y
 CONFIG_ARM_AT91_ETHER=y
@@ -47,8 +50,8 @@
 # CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
 CONFIG_AT91_SPI=y
 # CONFIG_AT91_SPIDEV is not set
-CONFIG_AT91_VLIO=y
 # CONFIG_ATMEL_TCLIB is not set
+CONFIG_ATM_DRIVERS=y
 # CONFIG_ATM_DUMMY is not set
 # CONFIG_ATM_TCP is not set
 CONFIG_BASE_SMALL=0
@@ -115,17 +118,18 @@
 # CONFIG_FPE_NWFPE_XP is not set
 CONFIG_FRAME_POINTER=y
 CONFIG_FS_POSIX_ACL=y
-# CONFIG_FW_LOADER is not set
+CONFIG_FW_LOADER=m
+# CONFIG_GENERIC_CLOCKEVENTS is not set
 CONFIG_GENERIC_GPIO=y
 # CONFIG_GENERIC_TIME is not set
 CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HID=y
 CONFIG_HW_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_I2C is not set
-# CONFIG_IEEE80211 is not set
 # CONFIG_IKCONFIG is not set
 CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
 CONFIG_INITRAMFS_SOURCE=""
@@ -143,7 +147,6 @@
 # CONFIG_IP6_NF_RAW is not set
 # CONFIG_IP6_NF_TARGET_HL is not set
 # CONFIG_IP6_NF_TARGET_LOG is not set
-# CONFIG_IP_DCCP is not set
 # CONFIG_IP_NF_ARPTABLES is not set
 # CONFIG_IP_NF_MATCH_ADDRTYPE is not set
 # CONFIG_IP_NF_TARGET_LOG is not set
@@ -167,16 +170,16 @@
 # CONFIG_MACH_KAFA is not set
 # CONFIG_MACH_KB9200 is not set
 # CONFIG_MACH_ONEARM is not set
-CONFIG_MACH_VLINK=y
+# CONFIG_MACH_PICOTUX2XX is not set
 CONFIG_MMC=m
 CONFIG_MMC_AT91=m
 CONFIG_MMC_BLOCK=m
 # CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
 CONFIG_MTD=y
 # CONFIG_MTD_ABSENT is not set
 # CONFIG_MTD_AFS_PARTS is not set
 CONFIG_MTD_AT91_DATAFLASH=y
-CONFIG_MTD_AT91_PARTS=y
 CONFIG_MTD_BLKDEVS=y
 CONFIG_MTD_BLOCK=y
 # CONFIG_MTD_BLOCK2MTD is not set
@@ -189,6 +192,7 @@
 CONFIG_MTD_CMDLINE_PARTS=y
 # CONFIG_MTD_COMPLEX_MAPPINGS is not set
 # CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_DATAFLASH26 is not set
 # CONFIG_MTD_DEBUG is not set
 # CONFIG_MTD_DOC2000 is not set
 # CONFIG_MTD_DOC2001 is not set
@@ -201,7 +205,6 @@
 CONFIG_MTD_MAP_BANK_WIDTH_4=y
 # CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
 # CONFIG_MTD_MTDRAM is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
 # CONFIG_MTD_ONENAND is not set
 CONFIG_MTD_PARTITIONS=y
 # CONFIG_MTD_PHRAM is not set
@@ -209,19 +212,18 @@
 # CONFIG_MTD_RAM is not set
 # CONFIG_MTD_REDBOOT_PARTS is not set
 # CONFIG_MTD_ROM is not set
-# CONFIG_MTD_SLRAM is not set
 # CONFIG_MTD_ROOTFS_ROOT_DEV is not set
 # CONFIG_MTD_ROOTFS_SPLIT is not set
+# CONFIG_MTD_SLRAM is not set
+CONFIG_NETDEV_1000=y
 # CONFIG_NET_EMATCH is not set
 # CONFIG_NET_IPGRE_BROADCAST is not set
 # CONFIG_NET_PKTGEN is not set
-# CONFIG_NET_RADIO is not set
 CONFIG_NET_SCH_FIFO=y
 # CONFIG_NET_SCH_NETEM is not set
 # CONFIG_NEW_LEDS is not set
 # CONFIG_NO_IDLE_HZ is not set
 # CONFIG_NO_IOPORT is not set
-# CONFIG_NTFS_FS is not set
 # CONFIG_NVRAM is not set
 # CONFIG_OUTER_CACHE is not set
 CONFIG_PHYLIB=y
@@ -234,6 +236,7 @@
 CONFIG_RTC_LIB=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
 # CONFIG_SCSI_MULTI_LUN is not set
+CONFIG_SCSI_WAIT_SCAN=m
 # CONFIG_SERIAL_8250 is not set
 CONFIG_SERIAL_ATMEL=y
 CONFIG_SERIAL_ATMEL_CONSOLE=y
@@ -249,12 +252,12 @@
 CONFIG_SPLIT_PTLOCK_CPUS=4096
 CONFIG_SYSVIPC_SYSCTL=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+# CONFIG_TICK_ONESHOT is not set
 CONFIG_UID16=y
 # CONFIG_UNUSED_SYMBOLS is not set
 # CONFIG_USB_ARCH_HAS_EHCI is not set
 # CONFIG_USB_ATM is not set
 # CONFIG_USB_CATC is not set
-# CONFIG_USB_GTCO is not set
 # CONFIG_USB_KAWETH is not set
 CONFIG_USB_LIBUSUAL=y
 CONFIG_USB_MON=y
@@ -263,7 +266,6 @@
 CONFIG_USB_OHCI_HCD=m
 # CONFIG_USB_PEGASUS is not set
 # CONFIG_USB_PRINTER is not set
-# CONFIG_USB_RTL8150 is not set
 # CONFIG_USB_SERIAL_EDGEPORT is not set
 # CONFIG_USB_SERIAL_EDGEPORT_TI is not set
 # CONFIG_USB_SERIAL_FUNSOFT is not set
@@ -291,8 +293,8 @@
 # CONFIG_USB_STORAGE_USBAT is not set
 # CONFIG_USB_USBNET is not set
 # CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_YEALINK is not set
 CONFIG_VECTORS_BASE=0xffff0000
+# CONFIG_VGASTATE is not set
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_VT=y
 CONFIG_VT_CONSOLE=y

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/000-at91patches.patch
@@ -1,1 +1,10313 @@
+diff -urN -x CVS linux-2.6.21/arch/arm/boot/compressed/head-at91rm9200.S linux-2.6-stable/arch/arm/boot/compressed/head-at91rm9200.S
+--- linux-2.6.21/arch/arm/boot/compressed/head-at91rm9200.S	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/boot/compressed/head-at91rm9200.S	Tue May  8 12:13:30 2007
+@@ -67,6 +67,12 @@
+ 		cmp	r7, r3
+ 		beq	99f
+ 
++		@ Promwad Chub : 1181
++		mov	r3,	#(MACH_TYPE_CHUB & 0xff)
++		orr	r3, r3, #(MACH_TYPE_CHUB & 0xff00)
++		cmp	r7, r3
++		beq	99f
++
+ 		@ Unknown board, use the AT91RM9200DK board
+ 		@ mov	r7, #MACH_TYPE_AT91RM9200
+ 		mov	r7,	#(MACH_TYPE_AT91RM9200DK & 0xff)
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/Kconfig linux-2.6-stable/arch/arm/mach-at91/Kconfig
+--- linux-2.6.21/arch/arm/mach-at91/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/Kconfig	Wed May  9 10:20:54 2007
+@@ -17,6 +17,9 @@
+ config ARCH_AT91SAM9263
+ 	bool "AT91SAM9263"
+ 
++config ARCH_AT91SAM9RL
++	bool "AT91SAM9RL"
++
+ endchoice
+ 
+ # ----------------------------------------------------------
+@@ -87,6 +90,12 @@
+ 	help
+ 	  Select this if you are using Sperry-Sun's KAFA board.
+ 
++config MACH_CHUB
++	bool "Promwad Chub board"
++	depends on ARCH_AT91RM9200
++	help
++	  Select this if you are using Promwad's Chub board.
++
+ endif
+ 
+ # ----------------------------------------------------------
+@@ -111,6 +120,13 @@
+ 	  Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit
+ 	  <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933>
+ 
++config MACH_CAM60
++	bool "KwikByte CAM60 board"
++	depends on ARCH_AT91SAM9260
++	help
++	  Select this if you are using KwikByte's CAM60 board based on the Atmel AT91SAM9260.
++	  <http://www.kwikbyte.com>
++
+ endif
+ 
+ # ----------------------------------------------------------
+@@ -145,6 +161,20 @@
+ 
+ # ----------------------------------------------------------
+ 
++if ARCH_AT91SAM9RL
++
++comment "AT91SAM9RL Board Type"
++
++config MACH_AT91SAM9RLEK
++	bool "Atmel AT91SAM9RL-EK Evaluation Kit"
++	depends on ARCH_AT91SAM9RL
++	help
++	  Select this if you are using Atmel's AT91SAM9RL-EK Evaluation Kit.
++
++endif
++
++# ----------------------------------------------------------
++
+ comment "AT91 Board Options"
+ 
+ config MTD_AT91_DATAFLASH_CARD
+@@ -160,6 +190,20 @@
+ 	  On AT91SAM926x boards both types of NAND flash can be present
+ 	  (8 and 16 bit data bus width).
+ 
++config CSB300_WAKE_SW0
++	bool "CSB300 SW0 irq0 wakeup"
++	depends on MACH_CSB337 && PM
++	help
++	  If you have a CSB300 connected to your CSB337, this lets
++	  SW0 serve as a wakeup button.  It uses IRQ0.
++
++config CSB300_WAKE_SW1
++	bool "CSB300 SW1 gpio wakeup"
++	depends on MACH_CSB337 && PM
++	help
++	  If you have a CSB300 connected to your CSB337, this lets
++	  SW1 serve as a wakeup button.  It uses GPIO.
++
+ # ----------------------------------------------------------
+ 
+ comment "AT91 Feature Selections"
+@@ -170,6 +214,20 @@
+ 	  Select this if you need to program one or more of the PCK0..PCK3
+ 	  programmable clock outputs.
+ 
++config ATMEL_TCLIB
++	bool "Timer/Counter Library"
++	help
++	  Select this if you want a library to allocate the Timer/Counter
++	  blocks found on many Atmel processors.  This facilitates using
++	  these modules despite processor differences.
++
++config AT91_SLOW_CLOCK
++	bool "Suspend-to-RAM uses slow clock mode (EXPERIMENTAL)"
++	depends on PM && EXPERIMENTAL
++	help
++	  Select this if you wish to put the CPU into slow clock mode
++	  while in the "Suspend to RAM" state, to save more power.
++
+ endmenu
+ 
+ endif
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/Makefile linux-2.6-stable/arch/arm/mach-at91/Makefile
+--- linux-2.6.21/arch/arm/mach-at91/Makefile	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/Makefile	Wed May  9 12:37:19 2007
+@@ -8,12 +8,15 @@
+ obj-		:=
+ 
+ obj-$(CONFIG_PM)		+= pm.o
++obj-$(CONFIG_AT91_SLOW_CLOCK)	+= pm_slowclock.o
++obj-$(CONFIG_ATMEL_TCLIB)	+= tclib.o
+ 
+ # CPU-specific support
+ obj-$(CONFIG_ARCH_AT91RM9200)	+= at91rm9200.o at91rm9200_time.o at91rm9200_devices.o
+ obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o
+ obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o
+ obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263.o at91sam926x_time.o at91sam9263_devices.o
++obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o
+ 
+ # AT91RM9200 board-specific support
+ obj-$(CONFIG_MACH_ONEARM)	+= board-1arm.o
+@@ -25,9 +28,11 @@
+ obj-$(CONFIG_MACH_KB9200)	+= board-kb9202.o
+ obj-$(CONFIG_MACH_ATEB9200)	+= board-eb9200.o
+ obj-$(CONFIG_MACH_KAFA)		+= board-kafa.o
++obj-$(CONFIG_MACH_CHUB)		+= board-chub.o
+ 
+ # AT91SAM9260 board-specific support
+ obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
++obj-$(CONFIG_MACH_CAM60)	+= board-cam60.o
+ 
+ # AT91SAM9261 board-specific support
+ obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
+@@ -35,9 +40,13 @@
+ # AT91SAM9263 board-specific support
+ obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
+ 
++# AT91SAM9RL board-specific support
++obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
++
+ # LEDs support
+ led-$(CONFIG_ARCH_AT91RM9200DK)	+= leds.o
+ led-$(CONFIG_MACH_AT91RM9200EK)	+= leds.o
++led-$(CONFIG_MACH_AT91SAM9261EK)+= leds.o
+ led-$(CONFIG_MACH_CSB337)	+= leds.o
+ led-$(CONFIG_MACH_CSB637)	+= leds.o
+ led-$(CONFIG_MACH_KB9200)	+= leds.o
+@@ -45,7 +54,7 @@
+ obj-$(CONFIG_LEDS) += $(led-y)
+ 
+ # VGA support
+-#obj-$(CONFIG_FB_S1D13XXX)	+= ics1523.o
++obj-$(CONFIG_FB_S1D13XXX)	+= ics1523.o
+ 
+ 
+ ifeq ($(CONFIG_PM_DEBUG),y)
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91rm9200.c linux-2.6-stable/arch/arm/mach-at91/at91rm9200.c
+--- linux-2.6.21/arch/arm/mach-at91/at91rm9200.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/at91rm9200.c	Tue May  8 12:13:30 2007
+@@ -117,6 +117,21 @@
+ 	.pmc_mask	= 1 << AT91RM9200_ID_PIOD,
+ 	.type		= CLK_TYPE_PERIPHERAL,
+ };
++static struct clk ssc0_clk = {
++	.name		= "ssc0_clk",
++	.pmc_mask	= 1 << AT91RM9200_ID_SSC0,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ssc1_clk = {
++	.name		= "ssc1_clk",
++	.pmc_mask	= 1 << AT91RM9200_ID_SSC1,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ssc2_clk = {
++	.name		= "ssc2_clk",
++	.pmc_mask	= 1 << AT91RM9200_ID_SSC2,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
+ static struct clk tc0_clk = {
+ 	.name		= "tc0_clk",
+ 	.pmc_mask	= 1 << AT91RM9200_ID_TC0,
+@@ -161,7 +176,9 @@
+ 	&udc_clk,
+ 	&twi_clk,
+ 	&spi_clk,
+-	// ssc 0 .. ssc2
++	&ssc0_clk,
++	&ssc1_clk,
++	&ssc2_clk,
+ 	&tc0_clk,
+ 	&tc1_clk,
+ 	&tc2_clk,
+@@ -250,6 +267,33 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91rm9200_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91RM9200_BASE_TCB0,
++		.irq		= { AT91RM9200_ID_TC0, AT91RM9200_ID_TC1, AT91RM9200_ID_TC2 },
++		.clk		= { &tc0_clk, &tc1_clk, &tc2_clk },
++	},
++	[1] = {
++		.physaddr	= AT91RM9200_BASE_TCB1,
++		.irq		= { AT91RM9200_ID_TC3, AT91RM9200_ID_TC4, AT91RM9200_ID_TC5 },
++		.clk		= { &tc3_clk, &tc4_clk, &tc5_clk },
++	},
++};
++
++#define at91rm9200_tc_init()	atmel_tc_init(at91rm9200_tcblocks, ARRAY_SIZE(at91rm9200_tcblocks))
++
++#else
++#define at91rm9200_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91RM9200 processor initialization
+  * -------------------------------------------------------------------- */
+ void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks)
+@@ -271,6 +315,9 @@
+ 
+ 	/* Initialize GPIO subsystem */
+ 	at91_gpio_init(at91rm9200_gpio, banks);
++
++	/* Initialize the Timer/Counter blocks */
++	at91rm9200_tc_init();
+ }
+ 
+ 
+@@ -284,28 +331,28 @@
+ static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
+ 	7,	/* Advanced Interrupt Controller (FIQ) */
+ 	7,	/* System Peripherals */
+-	0,	/* Parallel IO Controller A */
+-	0,	/* Parallel IO Controller B */
+-	0,	/* Parallel IO Controller C */
+-	0,	/* Parallel IO Controller D */
+-	6,	/* USART 0 */
+-	6,	/* USART 1 */
+-	6,	/* USART 2 */
+-	6,	/* USART 3 */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C */
++	1,	/* Parallel IO Controller D */
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
++	5,	/* USART 3 */
+ 	0,	/* Multimedia Card Interface */
+-	4,	/* USB Device Port */
+-	0,	/* Two-Wire Interface */
+-	6,	/* Serial Peripheral Interface */
+-	5,	/* Serial Synchronous Controller 0 */
+-	5,	/* Serial Synchronous Controller 1 */
+-	5,	/* Serial Synchronous Controller 2 */
++	2,	/* USB Device Port */
++	6,	/* Two-Wire Interface */
++	5,	/* Serial Peripheral Interface */
++	4,	/* Serial Synchronous Controller 0 */
++	4,	/* Serial Synchronous Controller 1 */
++	4,	/* Serial Synchronous Controller 2 */
+ 	0,	/* Timer Counter 0 */
+ 	0,	/* Timer Counter 1 */
+ 	0,	/* Timer Counter 2 */
+ 	0,	/* Timer Counter 3 */
+ 	0,	/* Timer Counter 4 */
+ 	0,	/* Timer Counter 5 */
+-	3,	/* USB Host port */
++	2,	/* USB Host port */
+ 	3,	/* Ethernet MAC */
+ 	0,	/* Advanced Interrupt Controller (IRQ0) */
+ 	0,	/* Advanced Interrupt Controller (IRQ1) */
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91rm9200_devices.c linux-2.6-stable/arch/arm/mach-at91/at91rm9200_devices.c
+--- linux-2.6.21/arch/arm/mach-at91/at91rm9200_devices.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/at91rm9200_devices.c	Tue May  8 12:13:30 2007
+@@ -480,7 +480,18 @@
+  *  SPI
+  * -------------------------------------------------------------------- */
+ 
+-#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)
++#if defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)		/* legacy SPI driver */
++#define SPI_DEVNAME	"at91_spi"
++
++#elif defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE)	/* SPI bitbanging driver */
++#define SPI_DEVNAME	"at91_spi"
++
++#elif defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)	/* new SPI driver */
++#define SPI_DEVNAME	"atmel_spi"
++
++#endif
++
++#ifdef SPI_DEVNAME
+ static u64 spi_dmamask = 0xffffffffUL;
+ 
+ static struct resource spi_resources[] = {
+@@ -497,7 +508,7 @@
+ };
+ 
+ static struct platform_device at91rm9200_spi_device = {
+-	.name		= "at91_spi",
++	.name		= SPI_DEVNAME,
+ 	.id		= 0,
+ 	.dev		= {
+ 				.dma_mask		= &spi_dmamask,
+@@ -606,6 +617,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91sam9260.c linux-2.6-stable/arch/arm/mach-at91/at91sam9260.c
+--- linux-2.6.21/arch/arm/mach-at91/at91sam9260.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/at91sam9260.c	Tue May  8 12:13:30 2007
+@@ -119,6 +119,11 @@
+ 	.pmc_mask	= 1 << AT91SAM9260_ID_SPI1,
+ 	.type		= CLK_TYPE_PERIPHERAL,
+ };
++static struct clk ssc_clk = {
++	.name		= "ssc_clk",
++	.pmc_mask	= 1 << AT91SAM9260_ID_SSC,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
+ static struct clk tc0_clk = {
+ 	.name		= "tc0_clk",
+ 	.pmc_mask	= 1 << AT91SAM9260_ID_TC0,
+@@ -193,7 +198,7 @@
+ 	&twi_clk,
+ 	&spi0_clk,
+ 	&spi1_clk,
+-	// ssc
++	&ssc_clk,
+ 	&tc0_clk,
+ 	&tc1_clk,
+ 	&tc2_clk,
+@@ -264,6 +269,33 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91sam9260_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91SAM9260_BASE_TCB0,
++		.irq		= { AT91SAM9260_ID_TC0, AT91SAM9260_ID_TC1, AT91SAM9260_ID_TC2 },
++		.clk		= { &tc0_clk, &tc1_clk, &tc2_clk },
++	},
++	[1] = {
++		.physaddr	= AT91SAM9260_BASE_TCB1,
++		.irq		= { AT91SAM9260_ID_TC3, AT91SAM9260_ID_TC4, AT91SAM9260_ID_TC5 },
++		.clk		= { &tc3_clk, &tc4_clk, &tc5_clk },
++	},
++};
++
++#define at91sam9260_tc_init()	atmel_tc_init(at91sam9260_tcblocks, ARRAY_SIZE(at91sam9260_tcblocks))
++
++#else
++#define at91sam9260_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91SAM9260 processor initialization
+  * -------------------------------------------------------------------- */
+ 
+@@ -310,6 +342,9 @@
+ 
+ 	/* Register GPIO subsystem */
+ 	at91_gpio_init(at91sam9260_gpio, 3);
++
++	/* Initialize the Timer/Counter blocks */
++	at91sam9260_tc_init();
+ }
+ 
+ /* --------------------------------------------------------------------
+@@ -322,30 +357,30 @@
+ static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = {
+ 	7,	/* Advanced Interrupt Controller */
+ 	7,	/* System Peripherals */
+-	0,	/* Parallel IO Controller A */
+-	0,	/* Parallel IO Controller B */
+-	0,	/* Parallel IO Controller C */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C */
+ 	0,	/* Analog-to-Digital Converter */
+-	6,	/* USART 0 */
+-	6,	/* USART 1 */
+-	6,	/* USART 2 */
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
+ 	0,	/* Multimedia Card Interface */
+-	4,	/* USB Device Port */
+-	0,	/* Two-Wire Interface */
+-	6,	/* Serial Peripheral Interface 0 */
+-	6,	/* Serial Peripheral Interface 1 */
++	2,	/* USB Device Port */
++	6,	/* Two-Wire Interface */
++	5,	/* Serial Peripheral Interface 0 */
++	5,	/* Serial Peripheral Interface 1 */
+ 	5,	/* Serial Synchronous Controller */
+ 	0,
+ 	0,
+ 	0,	/* Timer Counter 0 */
+ 	0,	/* Timer Counter 1 */
+ 	0,	/* Timer Counter 2 */
+-	3,	/* USB Host port */
++	2,	/* USB Host port */
+ 	3,	/* Ethernet */
+ 	0,	/* Image Sensor Interface */
+-	6,	/* USART 3 */
+-	6,	/* USART 4 */
+-	6,	/* USART 5 */
++	5,	/* USART 3 */
++	5,	/* USART 4 */
++	5,	/* USART 5 */
+ 	0,	/* Timer Counter 3 */
+ 	0,	/* Timer Counter 4 */
+ 	0,	/* Timer Counter 5 */
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91sam9260_devices.c linux-2.6-stable/arch/arm/mach-at91/at91sam9260_devices.c
+--- linux-2.6.21/arch/arm/mach-at91/at91sam9260_devices.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/at91sam9260_devices.c	Tue May  8 12:13:30 2007
+@@ -527,6 +527,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91sam9261.c linux-2.6-stable/arch/arm/mach-at91/at91sam9261.c
+--- linux-2.6.21/arch/arm/mach-at91/at91sam9261.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/at91sam9261.c	Tue May  8 12:13:30 2007
+@@ -97,6 +97,21 @@
+ 	.pmc_mask	= 1 << AT91SAM9261_ID_SPI1,
+ 	.type		= CLK_TYPE_PERIPHERAL,
+ };
++static struct clk ssc0_clk = {
++	.name		= "ssc0_clk",
++	.pmc_mask	= 1 << AT91SAM9261_ID_SSC0,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ssc1_clk = {
++	.name		= "ssc1_clk",
++	.pmc_mask	= 1 << AT91SAM9261_ID_SSC1,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ssc2_clk = {
++	.name		= "ssc2_clk",
++	.pmc_mask	= 1 << AT91SAM9261_ID_SSC2,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
+ static struct clk tc0_clk = {
+ 	.name		= "tc0_clk",
+ 	.pmc_mask	= 1 << AT91SAM9261_ID_TC0,
+@@ -135,7 +150,9 @@
+ 	&twi_clk,
+ 	&spi0_clk,
+ 	&spi1_clk,
+-	// ssc 0 .. ssc2
++	&ssc0_clk,
++	&ssc1_clk,
++	&ssc2_clk,
+ 	&tc0_clk,
+ 	&tc1_clk,
+ 	&tc2_clk,
+@@ -230,6 +247,28 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91sam9261_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91SAM9261_BASE_TCB0,
++		.irq		= { AT91SAM9261_ID_TC0, AT91SAM9261_ID_TC1, AT91SAM9261_ID_TC2 },
++		.clk		= { &tc0_clk, &tc1_clk, &tc2_clk },
++	}
++};
++
++#define at91sam9261_tc_init()	atmel_tc_init(at91sam9261_tcblocks, ARRAY_SIZE(at91sam9261_tcblocks))
++
++#else
++#define at91sam9261_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91SAM9261 processor initialization
+  * -------------------------------------------------------------------- */
+ 
+@@ -250,6 +289,9 @@
+ 
+ 	/* Register GPIO subsystem */
+ 	at91_gpio_init(at91sam9261_gpio, 3);
++
++	/* Initialize the Timer/Counter blocks */
++	at91sam9261_tc_init();
+ }
+ 
+ /* --------------------------------------------------------------------
+@@ -262,25 +304,25 @@
+ static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = {
+ 	7,	/* Advanced Interrupt Controller */
+ 	7,	/* System Peripherals */
+-	0,	/* Parallel IO Controller A */
+-	0,	/* Parallel IO Controller B */
+-	0,	/* Parallel IO Controller C */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C */
+ 	0,
+-	6,	/* USART 0 */
+-	6,	/* USART 1 */
+-	6,	/* USART 2 */
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
+ 	0,	/* Multimedia Card Interface */
+-	4,	/* USB Device Port */
+-	0,	/* Two-Wire Interface */
+-	6,	/* Serial Peripheral Interface 0 */
+-	6,	/* Serial Peripheral Interface 1 */
+-	5,	/* Serial Synchronous Controller 0 */
+-	5,	/* Serial Synchronous Controller 1 */
+-	5,	/* Serial Synchronous Controller 2 */
++	2,	/* USB Device Port */
++	6,	/* Two-Wire Interface */
++	5,	/* Serial Peripheral Interface 0 */
++	5,	/* Serial Peripheral Interface 1 */
++	4,	/* Serial Synchronous Controller 0 */
++	4,	/* Serial Synchronous Controller 1 */
++	4,	/* Serial Synchronous Controller 2 */
+ 	0,	/* Timer Counter 0 */
+ 	0,	/* Timer Counter 1 */
+ 	0,	/* Timer Counter 2 */
+-	3,	/* USB Host port */
++	2,	/* USB Host port */
+ 	3,	/* LCD Controller */
+ 	0,
+ 	0,
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91sam9261_devices.c linux-2.6-stable/arch/arm/mach-at91/at91sam9261_devices.c
+--- linux-2.6.21/arch/arm/mach-at91/at91sam9261_devices.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/at91sam9261_devices.c	Tue May  8 12:56:33 2007
+@@ -14,6 +14,9 @@
+ #include <asm/mach/map.h>
+ 
+ #include <linux/platform_device.h>
++#include <linux/fb.h>
++
++#include <video/atmel_lcdc.h>
+ 
+ #include <asm/arch/board.h>
+ #include <asm/arch/gpio.h>
+@@ -430,9 +433,9 @@
+  *  LCD Controller
+  * -------------------------------------------------------------------- */
+ 
+-#if defined(CONFIG_FB_AT91) || defined(CONFIG_FB_AT91_MODULE)
++#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
+ static u64 lcdc_dmamask = 0xffffffffUL;
+-static struct at91fb_info lcdc_data;
++static struct atmel_lcdfb_info lcdc_data;
+ 
+ static struct resource lcdc_resources[] = {
+ 	[0] = {
+@@ -455,7 +458,7 @@
+ };
+ 
+ static struct platform_device at91_lcdc_device = {
+-	.name		= "at91-fb",
++	.name		= "atmel_lcdfb",
+ 	.id		= 0,
+ 	.dev		= {
+ 				.dma_mask		= &lcdc_dmamask,
+@@ -466,7 +469,7 @@
+ 	.num_resources	= ARRAY_SIZE(lcdc_resources),
+ };
+ 
+-void __init at91_add_device_lcdc(struct at91fb_info *data)
++void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+ {
+ 	if (!data) {
+ 		return;
+@@ -499,7 +502,7 @@
+ 	platform_device_register(&at91_lcdc_device);
+ }
+ #else
+-void __init at91_add_device_lcdc(struct at91fb_info *data) {}
++void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+ #endif
+ 
+ 
+@@ -525,6 +528,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91sam9263.c linux-2.6-stable/arch/arm/mach-at91/at91sam9263.c
+--- linux-2.6.21/arch/arm/mach-at91/at91sam9263.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/at91sam9263.c	Tue May  8 12:13:30 2007
+@@ -87,6 +87,11 @@
+ 	.pmc_mask	= 1 << AT91SAM9263_ID_MCI1,
+ 	.type		= CLK_TYPE_PERIPHERAL,
+ };
++static struct clk can_clk = {
++	.name		= "can_clk",
++	.pmc_mask	= 1 << AT91SAM9263_ID_CAN,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
+ static struct clk twi_clk = {
+ 	.name		= "twi_clk",
+ 	.pmc_mask	= 1 << AT91SAM9263_ID_TWI,
+@@ -102,16 +107,46 @@
+ 	.pmc_mask	= 1 << AT91SAM9263_ID_SPI1,
+ 	.type		= CLK_TYPE_PERIPHERAL,
+ };
++static struct clk ssc0_clk = {
++	.name		= "ssc0_clk",
++	.pmc_mask	= 1 << AT91SAM9263_ID_SSC0,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ssc1_clk = {
++	.name		= "ssc1_clk",
++	.pmc_mask	= 1 << AT91SAM9263_ID_SSC1,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ac97_clk = {
++	.name		= "ac97_clk",
++	.pmc_mask	= 1 << AT91SAM9263_ID_AC97C,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
+ static struct clk tcb_clk = {
+ 	.name		= "tcb_clk",
+ 	.pmc_mask	= 1 << AT91SAM9263_ID_TCB,
+ 	.type		= CLK_TYPE_PERIPHERAL,
+ };
++static struct clk pwmc_clk = {
++	.name		= "pwmc_clk",
++	.pmc_mask	= 1 << AT91SAM9263_ID_PWMC,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
+ static struct clk macb_clk = {
+ 	.name		= "macb_clk",
+ 	.pmc_mask	= 1 << AT91SAM9263_ID_EMAC,
+ 	.type		= CLK_TYPE_PERIPHERAL,
+ };
++static struct clk dma_clk = {
++	.name		= "dma_clk",
++	.pmc_mask	= 1 << AT91SAM9263_ID_DMA,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk twodge_clk = {
++	.name		= "2dge_clk",
++	.pmc_mask	= 1 << AT91SAM9263_ID_2DGE,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
+ static struct clk udc_clk = {
+ 	.name		= "udc_clk",
+ 	.pmc_mask	= 1 << AT91SAM9263_ID_UDP,
+@@ -142,20 +177,21 @@
+ 	&usart2_clk,
+ 	&mmc0_clk,
+ 	&mmc1_clk,
+-	// can
++	&can_clk,
+ 	&twi_clk,
+ 	&spi0_clk,
+ 	&spi1_clk,
+-	// ssc0 .. ssc1
+-	// ac97
++	&ssc0_clk,
++	&ssc1_clk,
++	&ac97_clk,
+ 	&tcb_clk,
+-	// pwmc
++	&pwmc_clk,
+ 	&macb_clk,
+-	// 2dge
++	&twodge_clk,
+ 	&udc_clk,
+ 	&isi_clk,
+ 	&lcdc_clk,
+-	// dma
++	&dma_clk,
+ 	&ohci_clk,
+ 	// irq0 .. irq1
+ };
+@@ -237,6 +273,28 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91sam9263_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91SAM9263_BASE_TCB0,
++		.irq		= { AT91SAM9263_ID_TCB, AT91SAM9263_ID_TCB, AT91SAM9263_ID_TCB },
++		.clk		= { &tcb_clk, &tcb_clk, &tcb_clk },
++	}
++};
++
++#define at91sam9263_tc_init()	atmel_tc_init(at91sam9263_tcblocks, ARRAY_SIZE(at91sam9263_tcblocks))
++
++#else
++#define at91sam9263_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91SAM9263 processor initialization
+  * -------------------------------------------------------------------- */
+ 
+@@ -256,6 +314,9 @@
+ 
+ 	/* Register GPIO subsystem */
+ 	at91_gpio_init(at91sam9263_gpio, 5);
++
++	/* Initialize the Timer/Counter blocks */
++	at91sam9263_tc_init();
+ }
+ 
+ /* --------------------------------------------------------------------
+@@ -268,34 +329,34 @@
+ static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
+ 	7,	/* Advanced Interrupt Controller (FIQ) */
+ 	7,	/* System Peripherals */
+-	0,	/* Parallel IO Controller A */
+-	0,	/* Parallel IO Controller B */
+-	0,	/* Parallel IO Controller C, D and E */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C, D and E */
+ 	0,
+ 	0,
+-	6,	/* USART 0 */
+-	6,	/* USART 1 */
+-	6,	/* USART 2 */
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
+ 	0,	/* Multimedia Card Interface 0 */
+ 	0,	/* Multimedia Card Interface 1 */
+-	4,	/* CAN */
+-	0,	/* Two-Wire Interface */
+-	6,	/* Serial Peripheral Interface 0 */
+-	6,	/* Serial Peripheral Interface 1 */
+-	5,	/* Serial Synchronous Controller 0 */
+-	5,	/* Serial Synchronous Controller 1 */
+-	6,	/* AC97 Controller */
++	3,	/* CAN */
++	6,	/* Two-Wire Interface */
++	5,	/* Serial Peripheral Interface 0 */
++	5,	/* Serial Peripheral Interface 1 */
++	4,	/* Serial Synchronous Controller 0 */
++	4,	/* Serial Synchronous Controller 1 */
++	5,	/* AC97 Controller */
+ 	0,	/* Timer Counter 0, 1 and 2 */
+ 	0,	/* Pulse Width Modulation Controller */
+ 	3,	/* Ethernet */
+ 	0,
+ 	0,	/* 2D Graphic Engine */
+-	3,	/* USB Device Port */
++	2,	/* USB Device Port */
+ 	0,	/* Image Sensor Interface */
+ 	3,	/* LDC Controller */
+ 	0,	/* DMA Controller */
+ 	0,
+-	3,	/* USB Host port */
++	2,	/* USB Host port */
+ 	0,	/* Advanced Interrupt Controller (IRQ0) */
+ 	0,	/* Advanced Interrupt Controller (IRQ1) */
+ };
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91sam9263_devices.c linux-2.6-stable/arch/arm/mach-at91/at91sam9263_devices.c
+--- linux-2.6.21/arch/arm/mach-at91/at91sam9263_devices.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/at91sam9263_devices.c	Thu May 10 12:23:46 2007
+@@ -13,6 +13,9 @@
+ #include <asm/mach/map.h>
+ 
+ #include <linux/platform_device.h>
++#include <linux/fb.h>
++
++#include <video/atmel_lcdc.h>
+ 
+ #include <asm/arch/board.h>
+ #include <asm/arch/gpio.h>
+@@ -573,6 +576,180 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  AC97
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_SND_AT91_AC97) || defined(CONFIG_SND_AT91_AC97_MODULE)
++static u64 ac97_dmamask = 0xffffffffUL;
++static struct atmel_ac97_data ac97_data;
++
++static struct resource ac97_resources[] = {
++	[0] = {
++		.start	= AT91SAM9263_BASE_AC97C,
++		.end	= AT91SAM9263_BASE_AC97C + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9263_ID_AC97C,
++		.end	= AT91SAM9263_ID_AC97C,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device at91sam9263_ac97_device = {
++	.name		= "ac97c",
++	.id		= 1,
++	.dev		= {
++				.dma_mask		= &ac97_dmamask,
++				.coherent_dma_mask	= 0xffffffff,
++				.platform_data		= &ac97_data,
++	},
++	.resource	= ac97_resources,
++	.num_resources	= ARRAY_SIZE(ac97_resources),
++};
++
++void __init at91_add_device_ac97(struct atmel_ac97_data *data)
++{
++	if (!data)
++		return;
++
++	at91_set_A_periph(AT91_PIN_PB0, 0);	/* AC97FS */
++	at91_set_A_periph(AT91_PIN_PB1, 0);	/* AC97CK */
++	at91_set_A_periph(AT91_PIN_PB2, 0);	/* AC97TX */
++	at91_set_A_periph(AT91_PIN_PB3, 0);	/* AC97RX */
++
++	/* reset */
++	if (data->reset_pin)
++		at91_set_gpio_output(data->reset_pin, 0);
++
++	ac97_data = *ek_data;
++	platform_device_register(&at91sam9263_ac97_device);
++}
++#else
++void __init at91_add_device_ac97(struct atmel_ac97_data *data) {}
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  Image Sensor Interface
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_VIDEO_AT91_ISI) || defined(CONFIG_VIDEO_AT91_ISI_MODULE)
++
++struct resource isi_resources[] = {
++	[0] = {
++		.start	= AT91SAM9263_BASE_ISI,
++		.end	= AT91SAM9263_BASE_ISI + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9263_ID_ISI,
++		.end	= AT91SAM9263_ID_ISI,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device at91sam9263_isi_device = {
++	.name		= "at91_isi",
++	.id		= -1,
++	.resource	= isi_resources,
++	.num_resources	= ARRAY_SIZE(isi_resources),
++};
++
++void __init at91_add_device_isi(void)
++{
++	at91_set_A_periph(AT91_PIN_PE0, 0);	/* ISI_D0 */
++	at91_set_A_periph(AT91_PIN_PE1, 0);	/* ISI_D1 */
++	at91_set_A_periph(AT91_PIN_PE2, 0);	/* ISI_D2 */
++	at91_set_A_periph(AT91_PIN_PE3, 0);	/* ISI_D3 */
++	at91_set_A_periph(AT91_PIN_PE4, 0);	/* ISI_D4 */
++	at91_set_A_periph(AT91_PIN_PE5, 0);	/* ISI_D5 */
++	at91_set_A_periph(AT91_PIN_PE6, 0);	/* ISI_D6 */
++	at91_set_A_periph(AT91_PIN_PE7, 0);	/* ISI_D7 */
++	at91_set_A_periph(AT91_PIN_PE8, 0);	/* ISI_PCK */
++	at91_set_A_periph(AT91_PIN_PE9, 0);	/* ISI_HSYNC */
++	at91_set_A_periph(AT91_PIN_PE10, 0);	/* ISI_VSYNC */
++	at91_set_B_periph(AT91_PIN_PE11, 0);	/* ISI_MCK (PCK3) */
++	at91_set_B_periph(AT91_PIN_PE12, 0);	/* ISI_PD8 */
++	at91_set_B_periph(AT91_PIN_PE13, 0);	/* ISI_PD9 */
++	at91_set_B_periph(AT91_PIN_PE14, 0);	/* ISI_PD10 */
++	at91_set_B_periph(AT91_PIN_PE15, 0);	/* ISI_PD11 */
++}
++#else
++void __init at91_add_device_isi(void) {}
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  LCD Controller
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
++static u64 lcdc_dmamask = 0xffffffffUL;
++static struct atmel_lcdfb_info lcdc_data;
++
++static struct resource lcdc_resources[] = {
++	[0] = {
++		.start	= AT91SAM9263_LCDC_BASE,
++		.end	= AT91SAM9263_LCDC_BASE + SZ_4K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9263_ID_LCDC,
++		.end	= AT91SAM9263_ID_LCDC,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device at91_lcdc_device = {
++	.name		= "atmel_lcdfb",
++	.id		= 0,
++	.dev		= {
++				.dma_mask		= &lcdc_dmamask,
++				.coherent_dma_mask	= 0xffffffff,
++				.platform_data		= &lcdc_data,
++	},
++	.resource	= lcdc_resources,
++	.num_resources	= ARRAY_SIZE(lcdc_resources),
++};
++
++void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
++{
++	if (!data)
++		return;
++
++	at91_set_A_periph(AT91_PIN_PC1, 0);	/* LCDHSYNC */
++	at91_set_A_periph(AT91_PIN_PC2, 0);	/* LCDDOTCK */
++	at91_set_A_periph(AT91_PIN_PC3, 0);	/* LCDDEN */
++	at91_set_B_periph(AT91_PIN_PB9, 0);	/* LCDCC */
++	at91_set_A_periph(AT91_PIN_PC6, 0);	/* LCDD2 */
++	at91_set_A_periph(AT91_PIN_PC7, 0);	/* LCDD3 */
++	at91_set_A_periph(AT91_PIN_PC8, 0);	/* LCDD4 */
++	at91_set_A_periph(AT91_PIN_PC9, 0);	/* LCDD5 */
++	at91_set_A_periph(AT91_PIN_PC10, 0);	/* LCDD6 */
++	at91_set_A_periph(AT91_PIN_PC11, 0);	/* LCDD7 */
++	at91_set_A_periph(AT91_PIN_PC14, 0);	/* LCDD10 */
++	at91_set_A_periph(AT91_PIN_PC15, 0);	/* LCDD11 */
++	at91_set_A_periph(AT91_PIN_PC16, 0);	/* LCDD12 */
++	at91_set_B_periph(AT91_PIN_PC12, 0);	/* LCDD13 */
++	at91_set_A_periph(AT91_PIN_PC18, 0);	/* LCDD14 */
++	at91_set_A_periph(AT91_PIN_PC19, 0);	/* LCDD15 */
++	at91_set_A_periph(AT91_PIN_PC22, 0);	/* LCDD18 */
++	at91_set_A_periph(AT91_PIN_PC23, 0);	/* LCDD19 */
++	at91_set_A_periph(AT91_PIN_PC24, 0);	/* LCDD20 */
++	at91_set_B_periph(AT91_PIN_PC17, 0);	/* LCDD21 */
++	at91_set_A_periph(AT91_PIN_PC26, 0);	/* LCDD22 */
++	at91_set_A_periph(AT91_PIN_PC27, 0);	/* LCDD23 */
++
++	lcdc_data = *data;
++	platform_device_register(&at91_lcdc_device);
++}
++#else
++void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  LEDs
+  * -------------------------------------------------------------------- */
+ 
+@@ -594,6 +771,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91sam9rl.c linux-2.6-stable/arch/arm/mach-at91/at91sam9rl.c
+--- linux-2.6.21/arch/arm/mach-at91/at91sam9rl.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/at91sam9rl.c	Fri May 11 15:48:14 2007
+@@ -0,0 +1,366 @@
++/*
++ * arch/arm/mach-at91/at91sam9rl.c
++ *
++ *  Copyright (C) 2005 SAN People
++ *  Copyright (C) 2007 Atmel Corporation
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file COPYING in the main directory of this archive for
++ * more details.
++ */
++
++#include <linux/module.h>
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/arch/cpu.h>
++#include <asm/arch/at91sam9rl.h>
++#include <asm/arch/at91_pmc.h>
++#include <asm/arch/at91_rstc.h>
++
++#include "generic.h"
++#include "clock.h"
++
++static struct map_desc at91sam9rl_io_desc[] __initdata = {
++	{
++		.virtual	= AT91_VA_BASE_SYS,
++		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
++		.length		= SZ_16K,
++		.type		= MT_DEVICE,
++	},
++};
++
++static struct map_desc at91sam9rl_sram_desc[] __initdata = {
++	{
++		.pfn		= __phys_to_pfn(AT91SAM9RL_SRAM_BASE),
++		.type		= MT_DEVICE,
++	}
++};
++
++/* --------------------------------------------------------------------
++ *  Clocks
++ * -------------------------------------------------------------------- */
++
++/*
++ * The peripheral clocks.
++ */
++static struct clk pioA_clk = {
++	.name		= "pioA_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_PIOA,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk pioB_clk = {
++	.name		= "pioB_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_PIOB,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk pioC_clk = {
++	.name		= "pioC_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_PIOC,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk pioD_clk = {
++	.name		= "pioD_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_PIOD,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk usart0_clk = {
++	.name		= "usart0_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_US0,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk usart1_clk = {
++	.name		= "usart1_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_US1,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk usart2_clk = {
++	.name		= "usart2_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_US2,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk usart3_clk = {
++	.name		= "usart3_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_US3,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk mmc_clk = {
++	.name		= "mci_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_MCI,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk twi0_clk = {
++	.name		= "twi0_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_TWI0,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk twi1_clk = {
++	.name		= "twi1_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_TWI1,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk spi_clk = {
++	.name		= "spi_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_SPI,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ssc0_clk = {
++	.name		= "ssc0_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_SSC0,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ssc1_clk = {
++	.name		= "ssc1_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_SSC1,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk tc0_clk = {
++	.name		= "tc0_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_TC0,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk tc1_clk = {
++	.name		= "tc1_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_TC1,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk tc2_clk = {
++	.name		= "tc2_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_TC2,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk pwmc_clk = {
++	.name		= "pwmc_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_PWMC,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk tsc_clk = {
++	.name		= "tsc_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_TSC,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk dma_clk = {
++	.name		= "dma_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_DMA,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk udphs_clk = {
++	.name		= "udphs_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_UDPHS,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk lcdc_clk = {
++	.name		= "lcdc_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_LCDC,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++static struct clk ac97_clk = {
++	.name		= "ac97_clk",
++	.pmc_mask	= 1 << AT91SAM9RL_ID_AC97C,
++	.type		= CLK_TYPE_PERIPHERAL,
++};
++
++static struct clk *periph_clocks[] __initdata = {
++	&pioA_clk,
++	&pioB_clk,
++	&pioC_clk,
++	&pioD_clk,
++	&usart0_clk,
++	&usart1_clk,
++	&usart2_clk,
++	&usart3_clk,
++	&mmc_clk,
++	&twi0_clk,
++	&twi1_clk,
++	&spi_clk,
++	&ssc0_clk,
++	&ssc1_clk,
++	&tc0_clk,
++	&tc1_clk,
++	&tc2_clk,
++	&pwmc_clk,
++	&tsc_clk,
++	&dma_clk,
++	&udphs_clk,
++	&lcdc_clk,
++	&ac97_clk,
++	// irq0
++};
++
++/*
++ * The two programmable clocks.
++ * You must configure pin multiplexing to bring these signals out.
++ */
++static struct clk pck0 = {
++	.name		= "pck0",
++	.pmc_mask	= AT91_PMC_PCK0,
++	.type		= CLK_TYPE_PROGRAMMABLE,
++	.id		= 0,
++};
++static struct clk pck1 = {
++	.name		= "pck1",
++	.pmc_mask	= AT91_PMC_PCK1,
++	.type		= CLK_TYPE_PROGRAMMABLE,
++	.id		= 1,
++};
++
++static void __init at91sam9rl_register_clocks(void)
++{
++	int i;
++
++	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
++		clk_register(periph_clocks[i]);
++
++	clk_register(&pck0);
++	clk_register(&pck1);
++}
++
++/* --------------------------------------------------------------------
++ *  GPIO
++ * -------------------------------------------------------------------- */
++
++static struct at91_gpio_bank at91sam9rl_gpio[] = {
++	{
++		.id		= AT91SAM9RL_ID_PIOA,
++		.offset		= AT91_PIOA,
++		.clock		= &pioA_clk,
++	}, {
++		.id		= AT91SAM9RL_ID_PIOB,
++		.offset		= AT91_PIOB,
++		.clock		= &pioB_clk,
++	}, {
++		.id		= AT91SAM9RL_ID_PIOC,
++		.offset		= AT91_PIOC,
++		.clock		= &pioC_clk,
++	}, {
++		.id		= AT91SAM9RL_ID_PIOD,
++		.offset		= AT91_PIOD,
++		.clock		= &pioD_clk,
++	}
++};
++
++static void at91sam9rl_reset(void)
++{
++	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
++}
++
++
++/* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91sam9rl_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91SAM9RL_BASE_TCB0,
++		.irq		= { AT91SAM9RL_ID_TC0, AT91SAM9RL_ID_TC1, AT91SAM9RL_ID_TC2 },
++		.clk		= { &tc0_clk, &tc1_clk, &tc2_clk },
++	}
++};
++
++#define at91sam9rl_tc_init()	atmel_tc_init(at91sam9rl_tcblocks, ARRAY_SIZE(at91sam9rl_tcblocks))
++
++#else
++#define at91sam9rl_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  AT91SAM9RL processor initialization
++ * -------------------------------------------------------------------- */
++
++void __init at91sam9rl_initialize(unsigned long main_clock)
++{
++	unsigned long cidr, sram_size;
++
++	/* Map peripherals */
++	iotable_init(at91sam9rl_io_desc, ARRAY_SIZE(at91sam9rl_io_desc));
++
++	cidr = at91_sys_read(AT91_DBGU_CIDR);
++
++	switch (cidr & AT91_CIDR_SRAMSIZ) {
++		case AT91_CIDR_SRAMSIZ_32K:
++			sram_size = 2 * SZ_16K;
++			break;
++		case AT91_CIDR_SRAMSIZ_16K:
++		default:
++			sram_size = SZ_16K;
++	}
++
++	at91sam9rl_sram_desc->virtual = AT91_IO_VIRT_BASE - sram_size;
++	at91sam9rl_sram_desc->length = sram_size;
++
++	/* Map SRAM */
++	iotable_init(at91sam9rl_sram_desc, ARRAY_SIZE(at91sam9rl_sram_desc));
++
++	at91_arch_reset = at91sam9rl_reset;
++	at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0);
++
++	/* Init clock subsystem */
++	at91_clock_init(main_clock);
++
++	/* Register the processor-specific clocks */
++	at91sam9rl_register_clocks();
++
++	/* Register GPIO subsystem */
++	at91_gpio_init(at91sam9rl_gpio, 4);
++	
++	/* Initialize the Timer/Counter blocks */
++	at91sam9rl_tc_init();
++}
++
++/* --------------------------------------------------------------------
++ *  Interrupt initialization
++ * -------------------------------------------------------------------- */
++
++/*
++ * The default interrupt priority levels (0 = lowest, 7 = highest).
++ */
++static unsigned int at91sam9rl_default_irq_priority[NR_AIC_IRQS] __initdata = {
++	7,	/* Advanced Interrupt Controller */
++	7,	/* System Peripherals */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C */
++	1,	/* Parallel IO Controller D */
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
++	5,	/* USART 3 */
++	0,	/* Multimedia Card Interface */
++	6,	/* Two-Wire Interface 0 */
++	6,	/* Two-Wire Interface 1 */
++	5,	/* Serial Peripheral Interface */
++	4,	/* Serial Synchronous Controller 0 */
++	4,	/* Serial Synchronous Controller 1 */
++	0,	/* Timer Counter 0 */
++	0,	/* Timer Counter 1 */
++	0,	/* Timer Counter 2 */
++	0,
++	0,	/* Touch Screen Controller */
++	0,	/* DMA Controller */
++	2,	/* USB Device High speed port */
++	2,	/* LCD Controller */
++	6,	/* AC97 Controller */
++	0,
++	0,
++	0,
++	0,
++	0,
++	0,
++	0,	/* Advanced Interrupt Controller */
++};
++
++void __init at91sam9rl_init_interrupts(unsigned int priority[NR_AIC_IRQS])
++{
++	if (!priority)
++		priority = at91sam9rl_default_irq_priority;
++
++	/* Initialize the AIC interrupt controller */
++	at91_aic_init(priority);
++
++	/* Enable GPIO interrupts */
++	at91_gpio_irq_setup();
++}
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/at91sam9rl_devices.c linux-2.6-stable/arch/arm/mach-at91/at91sam9rl_devices.c
+--- linux-2.6.21/arch/arm/mach-at91/at91sam9rl_devices.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/at91sam9rl_devices.c	Fri May 11 16:03:25 2007
+@@ -0,0 +1,660 @@
++/*
++ *  Copyright (C) 2007 Atmel Corporation
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file COPYING in the main directory of this archive for
++ * more details.
++ */
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++
++#include <linux/platform_device.h>
++#include <linux/fb.h>
++
++#include <video/atmel_lcdc.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++#include <asm/arch/at91sam9rl.h>
++#include <asm/arch/at91sam9rl_matrix.h>
++#include <asm/arch/at91sam926x_mc.h>
++
++#include "generic.h"
++
++#define SZ_512	0x00000200
++#define SZ_256	0x00000100
++#define SZ_16	0x00000010
++
++
++/* --------------------------------------------------------------------
++ *  MMC / SD
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
++static u64 mmc_dmamask = 0xffffffffUL;
++static struct at91_mmc_data mmc_data;
++
++static struct resource mmc_resources[] = {
++	[0] = {
++		.start	= AT91SAM9RL_BASE_MCI,
++		.end	= AT91SAM9RL_BASE_MCI + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9RL_ID_MCI,
++		.end	= AT91SAM9RL_ID_MCI,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device at91sam9rl_mmc_device = {
++	.name		= "at91_mci",
++	.id		= -1,
++	.dev		= {
++				.dma_mask		= &mmc_dmamask,
++				.coherent_dma_mask	= 0xffffffff,
++				.platform_data		= &mmc_data,
++	},
++	.resource	= mmc_resources,
++	.num_resources	= ARRAY_SIZE(mmc_resources),
++};
++
++void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
++{
++	if (!data)
++		return;
++
++	/* input/irq */
++	if (data->det_pin) {
++		at91_set_gpio_input(data->det_pin, 1);
++		at91_set_deglitch(data->det_pin, 1);
++	}
++	if (data->wp_pin)
++		at91_set_gpio_input(data->wp_pin, 1);
++	if (data->vcc_pin)
++		at91_set_gpio_output(data->vcc_pin, 0);
++
++	/* CLK */
++	at91_set_A_periph(AT91_PIN_PA2, 0);
++
++	/* CMD */
++	at91_set_A_periph(AT91_PIN_PA1, 1);
++
++	/* DAT0, maybe DAT1..DAT3 */
++	at91_set_A_periph(AT91_PIN_PA0, 1);
++	if (data->wire4) {
++		at91_set_A_periph(AT91_PIN_PA3, 1);
++		at91_set_A_periph(AT91_PIN_PA4, 1);
++		at91_set_A_periph(AT91_PIN_PA5, 1);
++	}
++
++	mmc_data = *data;
++	platform_device_register(&at91sam9rl_mmc_device);
++}
++#else
++void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  NAND / SmartMedia
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
++static struct at91_nand_data nand_data;
++
++#define NAND_BASE	AT91_CHIPSELECT_3
++
++static struct resource nand_resources[] = {
++	{
++		.start	= NAND_BASE,
++		.end	= NAND_BASE + SZ_256M - 1,
++		.flags	= IORESOURCE_MEM,
++	}
++};
++
++static struct platform_device at91_nand_device = {
++	.name		= "at91_nand",
++	.id		= -1,
++	.dev		= {
++				.platform_data	= &nand_data,
++	},
++	.resource	= nand_resources,
++	.num_resources	= ARRAY_SIZE(nand_resources),
++};
++
++void __init at91_add_device_nand(struct at91_nand_data *data)
++{
++	unsigned long csa;
++
++	if (!data)
++		return;
++
++	csa = at91_sys_read(AT91_MATRIX_EBICSA);
++	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
++
++	/* set the bus interface characteristics */
++	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0)
++			| AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
++
++	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(2) | AT91_SMC_NCS_WRPULSE_(5)
++			| AT91_SMC_NRDPULSE_(2) | AT91_SMC_NCS_RDPULSE_(5));
++
++	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
++
++	at91_sys_write(AT91_SMC_MODE(3), AT91_SMC_DBW_8 | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1));
++
++	/* enable pin */
++	if (data->enable_pin)
++		at91_set_gpio_output(data->enable_pin, 1);
++
++	/* ready/busy pin */
++	if (data->rdy_pin)
++		at91_set_gpio_input(data->rdy_pin, 1);
++
++	/* card detect pin */
++	if (data->det_pin)
++		at91_set_gpio_input(data->det_pin, 1);
++
++	at91_set_A_periph(AT91_PIN_PB4, 0);		/* NANDOE */
++	at91_set_A_periph(AT91_PIN_PB5, 0);		/* NANDWE */
++
++	nand_data = *data;
++	platform_device_register(&at91_nand_device);
++}
++
++#else
++void __init at91_add_device_nand(struct at91_nand_data *data) {}
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  TWI (i2c)
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
++
++static struct resource twi_resources[] = {
++	[0] = {
++		.start	= AT91SAM9RL_BASE_TWI0,
++		.end	= AT91SAM9RL_BASE_TWI0 + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9RL_ID_TWI0,
++		.end	= AT91SAM9RL_ID_TWI0,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device at91sam9rl_twi_device = {
++	.name		= "at91_i2c",
++	.id		= -1,
++	.resource	= twi_resources,
++	.num_resources	= ARRAY_SIZE(twi_resources),
++};
++
++void __init at91_add_device_i2c(void)
++{
++	/* pins used for TWI interface */
++	at91_set_A_periph(AT91_PIN_PA23, 0);		/* TWD */
++	at91_set_multi_drive(AT91_PIN_PA23, 1);
++
++	at91_set_A_periph(AT91_PIN_PA24, 0);		/* TWCK */
++	at91_set_multi_drive(AT91_PIN_PA24, 1);
++
++	platform_device_register(&at91sam9rl_twi_device);
++}
++#else
++void __init at91_add_device_i2c(void) {}
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  SPI
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
++static u64 spi_dmamask = 0xffffffffUL;
++
++static struct resource spi_resources[] = {
++	[0] = {
++		.start	= AT91SAM9RL_BASE_SPI,
++		.end	= AT91SAM9RL_BASE_SPI + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9RL_ID_SPI,
++		.end	= AT91SAM9RL_ID_SPI,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device at91sam9rl_spi_device = {
++	.name		= "atmel_spi",
++	.id		= 0,
++	.dev		= {
++				.dma_mask		= &spi_dmamask,
++				.coherent_dma_mask	= 0xffffffff,
++	},
++	.resource	= spi_resources,
++	.num_resources	= ARRAY_SIZE(spi_resources),
++};
++
++static const unsigned spi_standard_cs[4] = { AT91_PIN_PA28, AT91_PIN_PB7, AT91_PIN_PD8, AT91_PIN_PD9 };
++
++
++void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
++{
++	int i;
++	unsigned long cs_pin;
++
++	at91_set_A_periph(AT91_PIN_PA25, 0);	/* MISO */
++	at91_set_A_periph(AT91_PIN_PA26, 0);	/* MOSI */
++	at91_set_A_periph(AT91_PIN_PA27, 0);	/* SPCK */
++
++	/* Enable SPI chip-selects */
++	for (i = 0; i < nr_devices; i++) {
++		if (devices[i].controller_data)
++			cs_pin = (unsigned long) devices[i].controller_data;
++		else
++			cs_pin = spi_standard_cs[devices[i].chip_select];
++
++		/* enable chip-select pin */
++		at91_set_gpio_output(cs_pin, 1);
++
++		/* pass chip-select pin to driver */
++		devices[i].controller_data = (void *) cs_pin;
++	}
++
++	spi_register_board_info(devices, nr_devices);
++	platform_device_register(&at91sam9rl_spi_device);
++}
++#else
++void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  LCD Controller
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
++static u64 lcdc_dmamask = 0xffffffffUL;
++static struct atmel_lcdfb_info lcdc_data;
++
++static struct resource lcdc_resources[] = {
++	[0] = {
++		.start	= AT91SAM9RL_LCDC_BASE,
++		.end	= AT91SAM9RL_LCDC_BASE + SZ_4K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9RL_ID_LCDC,
++		.end	= AT91SAM9RL_ID_LCDC,
++		.flags	= IORESOURCE_IRQ,
++	},
++#if defined(CONFIG_FB_INTSRAM)
++	[2] = {
++		.start	= AT91SAM9RL_SRAM_BASE,
++		.end	= AT91SAM9RL_SRAM_BASE + AT91SAM9RL_SRAM_SIZE - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++#endif
++};
++
++static struct platform_device at91_lcdc_device = {
++	.name		= "atmel_lcdfb",
++	.id		= 0,
++	.dev		= {
++				.dma_mask		= &lcdc_dmamask,
++				.coherent_dma_mask	= 0xffffffff,
++				.platform_data		= &lcdc_data,
++	},
++	.resource	= lcdc_resources,
++	.num_resources	= ARRAY_SIZE(lcdc_resources),
++};
++
++void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
++{
++	if (!data) {
++		return;
++	}
++
++#warning "Check this"
++	at91_set_B_periph(AT91_PIN_PC5, 0);	/* LCDHSYNC */
++	at91_set_B_periph(AT91_PIN_PC6, 0);	/* LCDDOTCK */
++	at91_set_B_periph(AT91_PIN_PC7, 0);	/* LCDDEN */
++	at91_set_B_periph(AT91_PIN_PC3, 0);	/* LCDCC */
++	at91_set_B_periph(AT91_PIN_PC9, 0);	/* LCDD3 */
++	at91_set_B_periph(AT91_PIN_PC10, 0);	/* LCDD4 */
++	at91_set_B_periph(AT91_PIN_PC11, 0);	/* LCDD5 */
++	at91_set_B_periph(AT91_PIN_PC12, 0);	/* LCDD6 */
++	at91_set_B_periph(AT91_PIN_PC13, 0);	/* LCDD7 */
++	at91_set_B_periph(AT91_PIN_PC15, 0);	/* LCDD11 */
++	at91_set_B_periph(AT91_PIN_PC16, 0);	/* LCDD12 */
++	at91_set_B_periph(AT91_PIN_PC17, 0);	/* LCDD13 */
++	at91_set_B_periph(AT91_PIN_PC18, 0);	/* LCDD14 */
++	at91_set_B_periph(AT91_PIN_PC19, 0);	/* LCDD15 */
++	at91_set_B_periph(AT91_PIN_PC20, 0);	/* LCDD18 */
++	at91_set_B_periph(AT91_PIN_PC21, 0);	/* LCDD19 */
++	at91_set_B_periph(AT91_PIN_PC22, 0);	/* LCDD20 */
++	at91_set_B_periph(AT91_PIN_PC23, 0);	/* LCDD21 */
++	at91_set_B_periph(AT91_PIN_PC24, 0);	/* LCDD22 */
++	at91_set_B_periph(AT91_PIN_PC25, 0);	/* LCDD23 */
++
++	lcdc_data = *data;
++	platform_device_register(&at91_lcdc_device);
++}
++#else
++void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  LEDs
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_LEDS)
++u8 at91_leds_cpu;
++u8 at91_leds_timer;
++
++void __init at91_init_leds(u8 cpu_led, u8 timer_led)
++{
++	/* Enable GPIO to access the LEDs */
++	at91_set_gpio_output(cpu_led, 1);
++	at91_set_gpio_output(timer_led, 1);
++
++	at91_leds_cpu	= cpu_led;
++	at91_leds_timer	= timer_led;
++}
++#else
++void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
++#endif
++
++
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
++/* --------------------------------------------------------------------
++ *  UART
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_SERIAL_ATMEL)
++static struct resource dbgu_resources[] = {
++	[0] = {
++		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
++		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91_ID_SYS,
++		.end	= AT91_ID_SYS,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct atmel_uart_data dbgu_data = {
++	.use_dma_tx	= 0,
++	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
++	.regs		= (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
++};
++
++static struct platform_device at91sam9rl_dbgu_device = {
++	.name		= "atmel_usart",
++	.id		= 0,
++	.dev		= {
++				.platform_data	= &dbgu_data,
++				.coherent_dma_mask = 0xffffffff,
++	},
++	.resource	= dbgu_resources,
++	.num_resources	= ARRAY_SIZE(dbgu_resources),
++};
++
++static inline void configure_dbgu_pins(void)
++{
++	at91_set_A_periph(AT91_PIN_PA21, 0);		/* DRXD */
++	at91_set_A_periph(AT91_PIN_PA22, 1);		/* DTXD */
++}
++
++static struct resource uart0_resources[] = {
++	[0] = {
++		.start	= AT91SAM9RL_BASE_US0,
++		.end	= AT91SAM9RL_BASE_US0 + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9RL_ID_US0,
++		.end	= AT91SAM9RL_ID_US0,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct atmel_uart_data uart0_data = {
++	.use_dma_tx	= 1,
++	.use_dma_rx	= 1,
++};
++
++static struct platform_device at91sam9rl_uart0_device = {
++	.name		= "atmel_usart",
++	.id		= 1,
++	.dev		= {
++				.platform_data	= &uart0_data,
++				.coherent_dma_mask = 0xffffffff,
++	},
++	.resource	= uart0_resources,
++	.num_resources	= ARRAY_SIZE(uart0_resources),
++};
++
++static inline void configure_usart0_pins(void)
++{
++	at91_set_A_periph(AT91_PIN_PA6, 1);		/* TXD0 */
++	at91_set_A_periph(AT91_PIN_PA7, 0);		/* RXD0 */
++	at91_set_A_periph(AT91_PIN_PA9, 0);		/* RTS0 */
++	at91_set_A_periph(AT91_PIN_PA10, 0);		/* CTS0 */
++}
++
++static struct resource uart1_resources[] = {
++	[0] = {
++		.start	= AT91SAM9RL_BASE_US1,
++		.end	= AT91SAM9RL_BASE_US1 + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9RL_ID_US1,
++		.end	= AT91SAM9RL_ID_US1,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct atmel_uart_data uart1_data = {
++	.use_dma_tx	= 1,
++	.use_dma_rx	= 1,
++};
++
++static struct platform_device at91sam9rl_uart1_device = {
++	.name		= "atmel_usart",
++	.id		= 2,
++	.dev		= {
++				.platform_data	= &uart1_data,
++				.coherent_dma_mask = 0xffffffff,
++	},
++	.resource	= uart1_resources,
++	.num_resources	= ARRAY_SIZE(uart1_resources),
++};
++
++static inline void configure_usart1_pins(void)
++{
++	at91_set_A_periph(AT91_PIN_PA11, 1);		/* TXD1 */
++	at91_set_A_periph(AT91_PIN_PA12, 0);		/* RXD1 */
++}
++
++static struct resource uart2_resources[] = {
++	[0] = {
++		.start	= AT91SAM9RL_BASE_US2,
++		.end	= AT91SAM9RL_BASE_US2 + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9RL_ID_US2,
++		.end	= AT91SAM9RL_ID_US2,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct atmel_uart_data uart2_data = {
++	.use_dma_tx	= 1,
++	.use_dma_rx	= 1,
++};
++
++static struct platform_device at91sam9rl_uart2_device = {
++	.name		= "atmel_usart",
++	.id		= 3,
++	.dev		= {
++				.platform_data	= &uart2_data,
++				.coherent_dma_mask = 0xffffffff,
++	},
++	.resource	= uart2_resources,
++	.num_resources	= ARRAY_SIZE(uart2_resources),
++};
++
++static inline void configure_usart2_pins(void)
++{
++	at91_set_A_periph(AT91_PIN_PA13, 1);		/* TXD2 */
++	at91_set_A_periph(AT91_PIN_PA14, 0);		/* RXD2 */
++}
++
++static struct resource uart3_resources[] = {
++	[0] = {
++		.start	= AT91SAM9RL_BASE_US3,
++		.end	= AT91SAM9RL_BASE_US3 + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9RL_ID_US3,
++		.end	= AT91SAM9RL_ID_US3,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct atmel_uart_data uart3_data = {
++	.use_dma_tx	= 1,
++	.use_dma_rx	= 1,
++};
++
++static struct platform_device at91sam9rl_uart3_device = {
++	.name		= "atmel_usart",
++	.id		= 4,
++	.dev		= {
++				.platform_data	= &uart3_data,
++				.coherent_dma_mask = 0xffffffff,
++	},
++	.resource	= uart3_resources,
++	.num_resources	= ARRAY_SIZE(uart3_resources),
++};
++
++static inline void configure_usart3_pins(void)
++{
++	at91_set_A_periph(AT91_PIN_PB0, 1);		/* TXD3 */
++	at91_set_A_periph(AT91_PIN_PB1, 0);		/* RXD3 */
++}
++
++struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
++struct platform_device *atmel_default_console_device;	/* the serial console device */
++
++void __init at91_init_serial(struct at91_uart_config *config)
++{
++	int i;
++
++	/* Fill in list of supported UARTs */
++	for (i = 0; i < config->nr_tty; i++) {
++		switch (config->tty_map[i]) {
++			case 0:
++				configure_usart0_pins();
++				at91_uarts[i] = &at91sam9rl_uart0_device;
++				at91_clock_associate("usart0_clk", &at91sam9rl_uart0_device.dev, "usart");
++				break;
++			case 1:
++				configure_usart1_pins();
++				at91_uarts[i] = &at91sam9rl_uart1_device;
++				at91_clock_associate("usart1_clk", &at91sam9rl_uart1_device.dev, "usart");
++				break;
++			case 2:
++				configure_usart2_pins();
++				at91_uarts[i] = &at91sam9rl_uart2_device;
++				at91_clock_associate("usart2_clk", &at91sam9rl_uart2_device.dev, "usart");
++				break;
++			case 3:
++				configure_usart3_pins();
++				at91_uarts[i] = &at91sam9rl_uart3_device;
++				at91_clock_associate("usart3_clk", &at91sam9rl_uart3_device.dev, "usart");
++				break;
++			case 4:
++				configure_dbgu_pins();
++				at91_uarts[i] = &at91sam9rl_dbgu_device;
++				at91_clock_associate("mck", &at91sam9rl_dbgu_device.dev, "usart");
++				break;
++			default:
++				continue;
++		}
++		at91_uarts[i]->id = i;		/* update ID number to mapped ID */
++	}
++
++	/* Set serial console device */
++	if (config->console_tty < ATMEL_MAX_UART)
++		atmel_default_console_device = at91_uarts[config->console_tty];
++	if (!atmel_default_console_device)
++		printk(KERN_INFO "AT91: No default serial console defined.\n");
++}
++
++void __init at91_add_device_serial(void)
++{
++	int i;
++
++	for (i = 0; i < ATMEL_MAX_UART; i++) {
++		if (at91_uarts[i])
++			platform_device_register(at91_uarts[i]);
++	}
++}
++#else
++void __init at91_init_serial(struct at91_uart_config *config) {}
++void __init at91_add_device_serial(void) {}
++#endif
++
++
++/* -------------------------------------------------------------------- */
++
++/*
++ * These devices are always present and don't need any board-specific
++ * setup.
++ */
++static int __init at91_add_standard_devices(void)
++{
++	return 0;
++}
++
++arch_initcall(at91_add_standard_devices);
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-cam60.c linux-2.6-stable/arch/arm/mach-at91/board-cam60.c
+--- linux-2.6.21/arch/arm/mach-at91/board-cam60.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/board-cam60.c	Tue May  8 12:13:30 2007
+@@ -0,0 +1,148 @@
++/*
++ * KwikByte CAM60
++ *
++ * based on board-sam9260ek.c
++ *   Copyright (C) 2005 SAN People
++ *   Copyright (C) 2006 Atmel
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++
++#include <linux/types.h>
++#include <linux/init.h>
++#include <linux/mm.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/spi/spi.h>
++#include <linux/spi/flash.h>
++
++#include <asm/hardware.h>
++#include <asm/setup.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/mach/irq.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++#include <asm/arch/at91sam926x_mc.h>
++
++#include "generic.h"
++
++
++/*
++ * Serial port configuration.
++ *    0 .. 5 = USART0 .. USART5
++ *    6      = DBGU
++ */
++static struct at91_uart_config __initdata cam60_uart_config = {
++	.console_tty	= 0,				/* ttyS0 */
++	.nr_tty		= 1,
++	.tty_map	= { 6, -1, -1, -1, -1, -1, -1 }	/* ttyS0, ..., ttyS6 */
++};
++
++static void __init cam60_map_io(void)
++{
++	/* Initialize processor: 10 MHz crystal */
++	at91sam9260_initialize(10000000);
++
++	/* Setup the serial ports and console */
++	at91_init_serial(&cam60_uart_config);
++}
++
++static void __init cam60_init_irq(void)
++{
++	at91sam9260_init_interrupts(NULL);
++}
++
++
++/*
++ * SPI devices.
++ */
++#if defined(CONFIG_MTD_DATAFLASH)
++static struct mtd_partition __initdata cam60_spi_partitions[] = {
++	{
++		.name	= "BOOT1",
++		.offset	= 0,
++		.size	= 4 * 1056,
++	},
++	{
++		.name	= "BOOT2",
++		.offset	= MTDPART_OFS_NXTBLK,
++		.size	= 256 * 1056,
++	},
++	{
++		.name	= "kernel",
++		.offset	= MTDPART_OFS_NXTBLK,
++		.size	= 2222 * 1056,
++	},
++	{
++		.name	= "file system",
++		.offset	= MTDPART_OFS_NXTBLK,
++		.size	= MTDPART_SIZ_FULL,
++	},
++};
++
++static struct flash_platform_data __initdata cam60_spi_flash_platform_data = {
++	.name		= "spi_flash",
++	.parts		= cam60_spi_partitions,
++	.nr_parts	= ARRAY_SIZE(cam60_spi_partitions)
++};
++#endif
++
++static struct spi_board_info cam60_spi_devices[] = {
++#if defined(CONFIG_MTD_DATAFLASH)
++	{	/* DataFlash chip */
++		.modalias	= "mtd_dataflash",
++		.chip_select	= 0,
++		.max_speed_hz	= 15 * 1000 * 1000,
++		.bus_num	= 0,
++		.platform_data	= &cam60_spi_flash_platform_data
++	},
++#endif
++};
++
++
++/*
++ * MACB Ethernet device
++ */
++static struct __initdata at91_eth_data cam60_macb_data = {
++	.phy_irq_pin	= AT91_PIN_PB5,
++	.is_rmii	= 0,
++};
++
++
++static void __init cam60_board_init(void)
++{
++	/* Serial */
++	at91_add_device_serial();
++	/* SPI */
++	at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices));
++	/* Ethernet */
++	at91_add_device_eth(&cam60_macb_data);
++}
++
++MACHINE_START(CAM60, "KwikByte CAM60")
++	/* Maintainer: KwikByte */
++	.phys_io	= AT91_BASE_SYS,
++	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
++	.boot_params	= AT91_SDRAM_BASE + 0x100,
++	.timer		= &at91sam926x_timer,
++	.map_io		= cam60_map_io,
++	.init_irq	= cam60_init_irq,
++	.init_machine	= cam60_board_init,
++MACHINE_END
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-chub.c linux-2.6-stable/arch/arm/mach-at91/board-chub.c
+--- linux-2.6.21/arch/arm/mach-at91/board-chub.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/board-chub.c	Tue May  8 12:13:30 2007
+@@ -0,0 +1,132 @@
++/*
++ * linux/arch/arm/mach-at91/board-chub.c
++ *
++ *  Copyright (C) 2005 SAN People, adapted for Promwad Chub board
++ *  by Kuten Ivan
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++
++#include <linux/types.h>
++#include <linux/init.h>
++#include <linux/mm.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++
++#include <asm/hardware.h>
++#include <asm/setup.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/mach/irq.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++
++#include "generic.h"
++
++/*
++ * Serial port configuration.
++ *    0 .. 3 = USART0 .. USART3
++ *    4      = DBGU
++ */
++static struct at91_uart_config __initdata chub_uart_config = {
++	.console_tty	= 0,				/* ttyS0 */
++	.nr_tty		= 5,
++	.tty_map	= { 4, 0, 1, 2, 3 }		/* ttyS0, ..., ttyS4 */
++};
++
++static void __init chub_init_irq(void)
++{
++	at91rm9200_init_interrupts(NULL);
++}
++
++static void __init chub_map_io(void)
++{
++	/* Initialize clocks: 18.432 MHz crystal */
++	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
++
++	/* Setup the serial ports and console */
++	at91_init_serial(&chub_uart_config);
++}
++
++static struct at91_eth_data __initdata chub_eth_data = {
++	.phy_irq_pin	= AT91_PIN_PB29,
++	.is_rmii	= 0,
++};
++
++static struct mtd_partition __initdata chub_nand_partition[] = {
++	{
++		.name	= "NAND Partition 1",
++		.offset = 0,
++		.size	= MTDPART_SIZ_FULL,
++	},
++};
++
++static struct mtd_partition *nand_partitions(int size, int *num_partitions)
++{
++	*num_partitions = ARRAY_SIZE(chub_nand_partition);
++	return chub_nand_partition;
++}
++
++static struct at91_nand_data __initdata chub_nand_data = {
++	.ale		= 22,
++	.cle		= 21,
++	.enable_pin	= AT91_PIN_PA27,
++	.partition_info	= nand_partitions,
++};
++
++static struct spi_board_info chub_spi_devices[] = {
++	{	/* DataFlash chip */
++		.modalias	= "mtd_dataflash",
++		.chip_select	= 0,
++		.max_speed_hz	= 15 * 1000 * 1000,
++	},
++};
++
++static void __init chub_board_init(void)
++{
++	/* Serial */
++	at91_add_device_serial();
++	/* I2C */
++	at91_add_device_i2c();
++	/* Ethernet */
++	at91_add_device_eth(&chub_eth_data);
++	/* SPI */
++	at91_add_device_spi(chub_spi_devices, ARRAY_SIZE(chub_spi_devices));
++	/* NAND Flash */
++	at91_add_device_nand(&chub_nand_data);
++	/* Disable write protect for NAND */
++	at91_set_gpio_output(AT91_PIN_PB7, 1);
++	/* Power enable for 3x RS-232 and 1x RS-485 */
++	at91_set_gpio_output(AT91_PIN_PB9, 1);
++	/* Disable write protect for FRAM */
++	at91_set_gpio_output(AT91_PIN_PA21, 1);
++	/* Disable write protect for Dataflash */
++	at91_set_gpio_output(AT91_PIN_PA19, 1);
++}
++
++MACHINE_START(CHUB, "Promwad Chub")
++	/* Maintainer: Ivan Kuten AT Promwad DOT com */
++	.phys_io	= AT91_BASE_SYS,
++	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
++	.boot_params	= AT91_SDRAM_BASE + 0x100,
++	.timer		= &at91rm9200_timer,
++	.map_io		= chub_map_io,
++	.init_irq	= chub_init_irq,
++	.init_machine	= chub_board_init,
++MACHINE_END
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-csb337.c linux-2.6-stable/arch/arm/mach-at91/board-csb337.c
+--- linux-2.6.21/arch/arm/mach-at91/board-csb337.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/board-csb337.c	Tue May  8 12:13:30 2007
+@@ -24,6 +24,7 @@
+ #include <linux/module.h>
+ #include <linux/platform_device.h>
+ #include <linux/spi/spi.h>
++#include <linux/interrupt.h>
+ #include <linux/mtd/physmap.h>
+ 
+ #include <asm/hardware.h>
+@@ -59,6 +60,7 @@
+ 
+ 	/* Setup the LEDs */
+ 	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
++	at91_set_gpio_output(AT91_PIN_PB2, 1);		/* third (unused) LED */
+ 
+ 	/* Setup the serial ports and console */
+ 	at91_init_serial(&csb337_uart_config);
+@@ -149,6 +151,55 @@
+ 	.num_resources	= ARRAY_SIZE(csb_flash_resources),
+ };
+ 
++static struct at91_gpio_led csb337_leds[] = {
++	{
++		.name		= "led0",
++		.gpio		= AT91_PIN_PB0,
++		.trigger	= "heartbeat",
++	},
++	{
++		.name		= "led1",
++		.gpio		= AT91_PIN_PB1,
++		.trigger	= "timer",
++	},
++	{
++		.name		= "led2",
++		.gpio		= AT91_PIN_PB2,
++	}
++};
++
++#if defined(CONFIG_CSB300_WAKE_SW0) || defined(CONFIG_CSB300_WAKE_SW1)
++static irqreturn_t switch_irq_handler(int irq, void *context)
++{
++	return IRQ_HANDLED;
++}
++
++static inline void __init switch_irq_setup(int irq, char *name, unsigned long mode)
++{
++	int res;
++
++	res = request_irq(irq, switch_irq_handler, IRQF_SAMPLE_RANDOM | mode, name, NULL);
++	if (res == 0)
++		enable_irq_wake(irq);
++}
++
++static void __init csb300_switches(void)
++{
++#ifdef CONFIG_CSB300_WAKE_SW0
++	at91_set_A_periph(AT91_PIN_PB29, 1);		/* IRQ0 */
++	switch_irq_setup(AT91RM9200_ID_IRQ0, "csb300_sw0", IRQF_TRIGGER_FALLING);
++#endif
++#ifdef CONFIG_CSB300_WAKE_SW1
++	at91_set_gpio_input(AT91_PIN_PB28, 1);
++	at91_set_deglitch(AT91_PIN_PB28, 1);
++	switch_irq_setup(AT91_PIN_PB28, "csb300_sw1", IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING);
++#endif
++	/* there's also SW2 at PA21, GPIO or TIOA2 */
++}
++#else
++static void __init csb300_switches(void) {}
++#endif
++
+ static void __init csb337_board_init(void)
+ {
+ 	/* Serial */
+@@ -168,8 +219,12 @@
+ 	at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
+ 	/* MMC */
+ 	at91_add_device_mmc(0, &csb337_mmc_data);
++	/* LEDS */
++	at91_gpio_leds(csb337_leds, ARRAY_SIZE(csb337_leds));
+ 	/* NOR flash */
+ 	platform_device_register(&csb_flash);
++	/* Switches on CSB300 */
++	csb300_switches();
+ }
+ 
+ MACHINE_START(CSB337, "Cogent CSB337")
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-dk.c linux-2.6-stable/arch/arm/mach-at91/board-dk.c
+--- linux-2.6.21/arch/arm/mach-at91/board-dk.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/board-dk.c	Tue May  8 14:29:12 2007
+@@ -73,6 +73,185 @@
+ 	at91rm9200_init_interrupts(NULL);
+ }
+ 
++#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
++#include <video/s1d13xxxfb.h>
++#include <asm/arch/ics1523.h>
++
++/* EPSON S1D13806 FB */
++#define AT91_FB_REG_BASE	0x30000000L
++#define AT91_FB_REG_SIZE	0x200
++#define AT91_FB_VMEM_BASE	0x30200000L
++#define AT91_FB_VMEM_SIZE	0x140000L
++
++static void __init dk_init_video(void)
++{
++	/* NWAIT Signal */
++	at91_set_A_periph(AT91_PIN_PC6, 0);
++
++	/* Initialization of the Static Memory Controller for Chip Select 2 */
++	at91_sys_write(AT91_SMC_CSR(2), AT91_SMC_DBW_16			/* 16 bit */
++				| AT91_SMC_WSEN | AT91_SMC_NWS_(4)	/* wait states */
++				| AT91_SMC_TDF_(1)			/* float time */
++	);
++
++	at91_ics1523_init();
++}
++
++/* CRT:    (active)   640x480 60Hz (PCLK=CLKI=25.175MHz)
++   Memory: Embedded SDRAM (MCLK=CLKI3=50.000MHz) (BUSCLK=60.000MHz) */
++static const struct s1d13xxxfb_regval dk_s1dfb_initregs[] = {
++	{S1DREG_MISC,			0x00},	/* Enable Memory/Register select bit */
++	{S1DREG_COM_DISP_MODE,		0x00},	/* disable display output */
++	{S1DREG_GPIO_CNF0,		0x00},
++	{S1DREG_GPIO_CNF1,		0x00},
++	{S1DREG_GPIO_CTL0,		0x08},
++	{S1DREG_GPIO_CTL1,		0x00},
++	{S1DREG_CLK_CNF,		0x01},	/* no divide, MCLK source is CLKI3 0x02*/
++	{S1DREG_LCD_CLK_CNF,		0x00},
++	{S1DREG_CRT_CLK_CNF,		0x00},
++	{S1DREG_MPLUG_CLK_CNF,		0x00},
++	{S1DREG_CPU2MEM_WST_SEL,	0x01},	/* 2*period(MCLK) - 4ns > period(BCLK) */
++	{S1DREG_SDRAM_REF_RATE,		0x03},	/* 32768 <= MCLK <= 50000 (MHz) */
++	{S1DREG_SDRAM_TC0,		0x00},	/* MCLK source freq (MHz): */
++	{S1DREG_SDRAM_TC1,		0x01},	/* 42 <= MCLK <= 50 */
++	{S1DREG_MEM_CNF,		0x80},	/* SDRAM Initialization - needed before mem access */
++	{S1DREG_PANEL_TYPE,		0x25},	/* std TFT 16bit, 8bit SCP format 2, single passive LCD */
++	{S1DREG_MOD_RATE,		0x00},	/* toggle every FPFRAME */
++	{S1DREG_LCD_DISP_HWIDTH,	0x4F},	/* 680 pix */
++	{S1DREG_LCD_NDISP_HPER,		0x12},	/* 152 pix */
++	{S1DREG_TFT_FPLINE_START,	0x01},	/* 13 pix */
++	{S1DREG_TFT_FPLINE_PWIDTH,	0x0B},	/* 96 pix */
++	{S1DREG_LCD_DISP_VHEIGHT0,	0xDF},
++	{S1DREG_LCD_DISP_VHEIGHT1,	0x01},	/* 480 lines */
++	{S1DREG_LCD_NDISP_VPER,		0x2C},	/* 44 lines */
++	{S1DREG_TFT_FPFRAME_START,	0x0A},	/* 10 lines */
++	{S1DREG_TFT_FPFRAME_PWIDTH,	0x01},	/* 2 lines */
++	{S1DREG_LCD_DISP_MODE,		0x05},  /* 16 bpp */
++	{S1DREG_LCD_MISC,		0x00},	/* dithering enabled, dual panel buffer enabled */
++	{S1DREG_LCD_DISP_START0,	0x00},
++	{S1DREG_LCD_DISP_START1,	0xC8},
++	{S1DREG_LCD_DISP_START2,	0x00},
++	{S1DREG_LCD_MEM_OFF0,		0x80},
++	{S1DREG_LCD_MEM_OFF1,		0x02},
++	{S1DREG_LCD_PIX_PAN,		0x00},
++	{S1DREG_LCD_DISP_FIFO_HTC,	0x3B},
++	{S1DREG_LCD_DISP_FIFO_LTC,	0x3C},
++	{S1DREG_CRT_DISP_HWIDTH,	0x4F},	/* 680 pix */
++	{S1DREG_CRT_NDISP_HPER,		0x13},	/* 160 pix */
++	{S1DREG_CRT_HRTC_START,		0x01},	/* 13 pix */
++	{S1DREG_CRT_HRTC_PWIDTH,	0x0B},	/* 96 pix */
++	{S1DREG_CRT_DISP_VHEIGHT0,	0xDF},
++	{S1DREG_CRT_DISP_VHEIGHT1,	0x01},	/* 480 lines */
++	{S1DREG_CRT_NDISP_VPER,		0x2B},	/* 44 lines */
++	{S1DREG_CRT_VRTC_START,		0x09},	/* 10 lines */
++	{S1DREG_CRT_VRTC_PWIDTH,	0x01},	/* 2 lines */
++	{S1DREG_TV_OUT_CTL,		0x10},
++	{S1DREG_CRT_DISP_MODE,		0x05},	/* 16 bpp */
++	{S1DREG_CRT_DISP_START0,	0x00},
++	{S1DREG_CRT_DISP_START1,	0x00},
++	{S1DREG_CRT_DISP_START2,	0x00},
++	{S1DREG_CRT_MEM_OFF0,		0x80},
++	{S1DREG_CRT_MEM_OFF1,		0x02},
++	{S1DREG_CRT_PIX_PAN,		0x00},
++	{S1DREG_CRT_DISP_FIFO_HTC,	0x3B},
++	{S1DREG_CRT_DISP_FIFO_LTC,	0x3C},
++	{S1DREG_LCD_CUR_CTL,		0x00},	/* inactive */
++	{S1DREG_LCD_CUR_START,		0x01},
++	{S1DREG_LCD_CUR_XPOS0,		0x00},
++	{S1DREG_LCD_CUR_XPOS1,		0x00},
++	{S1DREG_LCD_CUR_YPOS0,		0x00},
++	{S1DREG_LCD_CUR_YPOS1,		0x00},
++	{S1DREG_LCD_CUR_BCTL0,		0x00},
++	{S1DREG_LCD_CUR_GCTL0,		0x00},
++	{S1DREG_LCD_CUR_RCTL0,		0x00},
++	{S1DREG_LCD_CUR_BCTL1,		0x1F},
++	{S1DREG_LCD_CUR_GCTL1,		0x3F},
++	{S1DREG_LCD_CUR_RCTL1,		0x1F},
++	{S1DREG_LCD_CUR_FIFO_HTC,	0x00},
++	{S1DREG_CRT_CUR_CTL,		0x00},	/* inactive */
++	{S1DREG_CRT_CUR_START,		0x01},
++	{S1DREG_CRT_CUR_XPOS0,		0x00},
++	{S1DREG_CRT_CUR_XPOS1,		0x00},
++	{S1DREG_CRT_CUR_YPOS0,		0x00},
++	{S1DREG_CRT_CUR_YPOS1,		0x00},
++	{S1DREG_CRT_CUR_BCTL0,		0x00},
++	{S1DREG_CRT_CUR_GCTL0,		0x00},
++	{S1DREG_CRT_CUR_RCTL0,		0x00},
++	{S1DREG_CRT_CUR_BCTL1,		0x1F},
++	{S1DREG_CRT_CUR_GCTL1,		0x3F},
++	{S1DREG_CRT_CUR_RCTL1,		0x1F},
++	{S1DREG_CRT_CUR_FIFO_HTC,	0x00},
++	{S1DREG_BBLT_CTL0,		0x00},
++	{S1DREG_BBLT_CTL0,		0x00},
++	{S1DREG_BBLT_CC_EXP,		0x00},
++	{S1DREG_BBLT_OP,		0x00},
++	{S1DREG_BBLT_SRC_START0,	0x00},
++	{S1DREG_BBLT_SRC_START1,	0x00},
++	{S1DREG_BBLT_SRC_START2,	0x00},
++	{S1DREG_BBLT_DST_START0,	0x00},
++	{S1DREG_BBLT_DST_START1,	0x00},
++	{S1DREG_BBLT_DST_START2,	0x00},
++	{S1DREG_BBLT_MEM_OFF0,		0x00},
++	{S1DREG_BBLT_MEM_OFF1,		0x00},
++	{S1DREG_BBLT_WIDTH0,		0x00},
++	{S1DREG_BBLT_WIDTH1,		0x00},
++	{S1DREG_BBLT_HEIGHT0,		0x00},
++	{S1DREG_BBLT_HEIGHT1,		0x00},
++	{S1DREG_BBLT_BGC0,		0x00},
++	{S1DREG_BBLT_BGC1,		0x00},
++	{S1DREG_BBLT_FGC0,		0x00},
++	{S1DREG_BBLT_FGC1,		0x00},
++	{S1DREG_LKUP_MODE,		0x00},	/* LCD LUT r | LCD and CRT/TV LUT w */
++	{S1DREG_LKUP_ADDR,		0x00},
++	{S1DREG_PS_CNF,			0x00},	/* Power Save disable */
++	{S1DREG_PS_STATUS,		0x02},	/* LCD Panel down, mem up */
++	{S1DREG_CPU2MEM_WDOGT,		0x00},
++	{S1DREG_COM_DISP_MODE,		0x02},	/* enable CRT display output */
++};
++
++static struct s1d13xxxfb_pdata dk_s1dfb_pdata = {
++	.initregs		= dk_s1dfb_initregs,
++	.initregssize		= ARRAY_SIZE(dk_s1dfb_initregs),
++	.platform_init_video	= dk_init_video,
++};
++
++static u64 s1dfb_dmamask = 0xffffffffUL;
++
++static struct resource dk_s1dfb_resource[] = {
++	[0] = {	/* video mem */
++		.name   = "s1d13806 memory",
++		.start  = AT91_FB_VMEM_BASE,
++		.end    = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1,
++		.flags  = IORESOURCE_MEM,
++	},
++	[1] = {	/* video registers */
++		.name   = "s1d13806 registers",
++		.start  = AT91_FB_REG_BASE,
++		.end    = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1,
++		.flags  = IORESOURCE_MEM,
++	},
++};
++
++static struct platform_device dk_s1dfb_device = {
++	.name		= "s1d13806fb",
++	.id		= -1,
++	.dev		= {
++			.dma_mask		= &s1dfb_dmamask,
++			.coherent_dma_mask	= 0xffffffff,
++			.platform_data		= &dk_s1dfb_pdata,
++	},
++	.resource	= dk_s1dfb_resource,
++	.num_resources	= ARRAY_SIZE(dk_s1dfb_resource),
++};
++
++static void __init dk_add_device_video(void)
++{
++	platform_device_register(&dk_s1dfb_device);
++}
++#else
++static void __init dk_add_device_video(void) {}
++#endif
++
+ static struct at91_eth_data __initdata dk_eth_data = {
+ 	.phy_irq_pin	= AT91_PIN_PC4,
+ 	.is_rmii	= 1,
+@@ -151,7 +330,7 @@
+ #define DK_FLASH_SIZE	0x200000
+ 
+ static struct physmap_flash_data dk_flash_data = {
+-	.width	= 2,
++	.width		= 2,
+ };
+ 
+ static struct resource dk_flash_resource = {
+@@ -170,6 +349,13 @@
+ 	.num_resources	= 1,
+ };
+ 
++static struct at91_gpio_led dk_leds[] = {
++	{
++		.name		= "led0",
++		.gpio		= AT91_PIN_PB2,
++		.trigger	= "timer",
++	}
++};
+ 
+ static void __init dk_board_init(void)
+ {
+@@ -200,8 +386,10 @@
+ 	at91_add_device_nand(&dk_nand_data);
+ 	/* NOR Flash */
+ 	platform_device_register(&dk_flash);
++	/* LEDs */
++	at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
+ 	/* VGA */
+-//	dk_add_device_video();
++	dk_add_device_video();
+ }
+ 
+ MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-ek.c linux-2.6-stable/arch/arm/mach-at91/board-ek.c
+--- linux-2.6.21/arch/arm/mach-at91/board-ek.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/board-ek.c	Tue May  8 14:29:22 2007
+@@ -73,6 +73,187 @@
+ 	at91rm9200_init_interrupts(NULL);
+ }
+ 
++#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
++#include <video/s1d13xxxfb.h>
++#include <asm/arch/ics1523.h>
++
++/* EPSON S1D13806 FB */
++#define AT91_FB_REG_BASE	0x40000000L
++#define	AT91_FB_REG_SIZE	0x200
++#define AT91_FB_VMEM_BASE	0x40200000L
++#define AT91_FB_VMEM_SIZE	0x140000L
++
++static void __init ek_init_video(void)
++{
++	/* NWAIT Signal */
++	at91_set_A_periph(AT91_PIN_PC6, 0);
++
++	/* Initialization of the Static Memory Controller for Chip Select 3 */
++	at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_DBW_16			/* 16 bit */
++				| AT91_SMC_WSEN | AT91_SMC_NWS_(5)	/* wait states */
++				| AT91_SMC_TDF_(1)			/* float time */
++	);
++
++	at91_ics1523_init();
++}
++
++/* CRT:    (active)   640x480 60Hz (PCLK=CLKI=25.175MHz)
++   Memory: Embedded SDRAM (MCLK=CLKI3=50.000MHz) (BUSCLK=60.000MHz) */
++static const struct s1d13xxxfb_regval ek_s1dfb_initregs[] = {
++	{S1DREG_MISC,			0x00},	/* Enable Memory/Register select bit */
++	{S1DREG_COM_DISP_MODE,		0x00},	/* disable display output */
++	{S1DREG_GPIO_CNF0,		0xFF},	// 0x00
++	{S1DREG_GPIO_CNF1,		0x1F},	// 0x08
++	{S1DREG_GPIO_CTL0,		0x00},
++	{S1DREG_GPIO_CTL1,		0x00},
++	{S1DREG_CLK_CNF,		0x01},	/* no divide, MCLK source is CLKI3 0x02*/
++	{S1DREG_LCD_CLK_CNF,		0x00},
++	{S1DREG_CRT_CLK_CNF,		0x00},
++	{S1DREG_MPLUG_CLK_CNF,		0x00},
++	{S1DREG_CPU2MEM_WST_SEL,	0x01},	/* 2*period(MCLK) - 4ns > period(BCLK) */
++	{S1DREG_SDRAM_REF_RATE,		0x03},	/* 32768 <= MCLK <= 50000 (MHz) */
++	{S1DREG_SDRAM_TC0,		0x00},	/* MCLK source freq (MHz): */
++	{S1DREG_SDRAM_TC1,		0x01},	/* 42 <= MCLK <= 50 */
++	{S1DREG_MEM_CNF,		0x80},	/* SDRAM Initialization - needed before mem access */
++	{S1DREG_PANEL_TYPE,		0x25},	/* std TFT 16bit, 8bit SCP format 2, single passive LCD */
++	{S1DREG_MOD_RATE,		0x00},	/* toggle every FPFRAME */
++	{S1DREG_LCD_DISP_HWIDTH,	0x4F},	/* 680 pix */
++	{S1DREG_LCD_NDISP_HPER,		0x12},	/* 152 pix */
++	{S1DREG_TFT_FPLINE_START,	0x01},	/* 13 pix */
++	{S1DREG_TFT_FPLINE_PWIDTH,	0x0B},	/* 96 pix */
++	{S1DREG_LCD_DISP_VHEIGHT0,	0xDF},
++	{S1DREG_LCD_DISP_VHEIGHT1,	0x01},	/* 480 lines */
++	{S1DREG_LCD_NDISP_VPER,		0x2C},	/* 44 lines */
++	{S1DREG_TFT_FPFRAME_START,	0x0A},	/* 10 lines */
++	{S1DREG_TFT_FPFRAME_PWIDTH,	0x01},	/* 2 lines */
++	{S1DREG_LCD_DISP_MODE,		0x05},  /* 16 bpp */
++	{S1DREG_LCD_MISC,		0x00},	/* dithering enabled, dual panel buffer enabled */
++	{S1DREG_LCD_DISP_START0,	0x00},
++	{S1DREG_LCD_DISP_START1,	0xC8},
++	{S1DREG_LCD_DISP_START2,	0x00},
++	{S1DREG_LCD_MEM_OFF0,		0x80},
++	{S1DREG_LCD_MEM_OFF1,		0x02},
++	{S1DREG_LCD_PIX_PAN,		0x00},
++	{S1DREG_LCD_DISP_FIFO_HTC,	0x3B},
++	{S1DREG_LCD_DISP_FIFO_LTC,	0x3C},
++	{S1DREG_CRT_DISP_HWIDTH,	0x4F},	/* 680 pix */
++	{S1DREG_CRT_NDISP_HPER,		0x13},	/* 160 pix */
++	{S1DREG_CRT_HRTC_START,		0x01},	/* 13 pix */
++	{S1DREG_CRT_HRTC_PWIDTH,	0x0B},	/* 96 pix */
++	{S1DREG_CRT_DISP_VHEIGHT0,	0xDF},
++	{S1DREG_CRT_DISP_VHEIGHT1,	0x01},	/* 480 lines */
++	{S1DREG_CRT_NDISP_VPER,		0x2B},	/* 44 lines */
++	{S1DREG_CRT_VRTC_START,		0x09},	/* 10 lines */
++	{S1DREG_CRT_VRTC_PWIDTH,	0x01},	/* 2 lines */
++	{S1DREG_TV_OUT_CTL,		0x10},
++	{0x005E,			0x9F},
++	{0x005F,			0x00},
++	{S1DREG_CRT_DISP_MODE,		0x05},	/* 16 bpp */
++	{S1DREG_CRT_DISP_START0,	0x00},
++	{S1DREG_CRT_DISP_START1,	0x00},
++	{S1DREG_CRT_DISP_START2,	0x00},
++	{S1DREG_CRT_MEM_OFF0,		0x80},
++	{S1DREG_CRT_MEM_OFF1,		0x02},
++	{S1DREG_CRT_PIX_PAN,		0x00},
++	{S1DREG_CRT_DISP_FIFO_HTC,	0x3B},
++	{S1DREG_CRT_DISP_FIFO_LTC,	0x3C},
++	{S1DREG_LCD_CUR_CTL,		0x00},	/* inactive */
++	{S1DREG_LCD_CUR_START,		0x01},
++	{S1DREG_LCD_CUR_XPOS0,		0x00},
++	{S1DREG_LCD_CUR_XPOS1,		0x00},
++	{S1DREG_LCD_CUR_YPOS0,		0x00},
++	{S1DREG_LCD_CUR_YPOS1,		0x00},
++	{S1DREG_LCD_CUR_BCTL0,		0x00},
++	{S1DREG_LCD_CUR_GCTL0,		0x00},
++	{S1DREG_LCD_CUR_RCTL0,		0x00},
++	{S1DREG_LCD_CUR_BCTL1,		0x1F},
++	{S1DREG_LCD_CUR_GCTL1,		0x3F},
++	{S1DREG_LCD_CUR_RCTL1,		0x1F},
++	{S1DREG_LCD_CUR_FIFO_HTC,	0x00},
++	{S1DREG_CRT_CUR_CTL,		0x00},	/* inactive */
++	{S1DREG_CRT_CUR_START,		0x01},
++	{S1DREG_CRT_CUR_XPOS0,		0x00},
++	{S1DREG_CRT_CUR_XPOS1,		0x00},
++	{S1DREG_CRT_CUR_YPOS0,		0x00},
++	{S1DREG_CRT_CUR_YPOS1,		0x00},
++	{S1DREG_CRT_CUR_BCTL0,		0x00},
++	{S1DREG_CRT_CUR_GCTL0,		0x00},
++	{S1DREG_CRT_CUR_RCTL0,		0x00},
++	{S1DREG_CRT_CUR_BCTL1,		0x1F},
++	{S1DREG_CRT_CUR_GCTL1,		0x3F},
++	{S1DREG_CRT_CUR_RCTL1,		0x1F},
++	{S1DREG_CRT_CUR_FIFO_HTC,	0x00},
++	{S1DREG_BBLT_CTL0,		0x00},
++	{S1DREG_BBLT_CTL0,		0x00},
++	{S1DREG_BBLT_CC_EXP,		0x00},
++	{S1DREG_BBLT_OP,		0x00},
++	{S1DREG_BBLT_SRC_START0,	0x00},
++	{S1DREG_BBLT_SRC_START1,	0x00},
++	{S1DREG_BBLT_SRC_START2,	0x00},
++	{S1DREG_BBLT_DST_START0,	0x00},
++	{S1DREG_BBLT_DST_START1,	0x00},
++	{S1DREG_BBLT_DST_START2,	0x00},
++	{S1DREG_BBLT_MEM_OFF0,		0x00},
++	{S1DREG_BBLT_MEM_OFF1,		0x00},
++	{S1DREG_BBLT_WIDTH0,		0x00},
++	{S1DREG_BBLT_WIDTH1,		0x00},
++	{S1DREG_BBLT_HEIGHT0,		0x00},
++	{S1DREG_BBLT_HEIGHT1,		0x00},
++	{S1DREG_BBLT_BGC0,		0x00},
++	{S1DREG_BBLT_BGC1,		0x00},
++	{S1DREG_BBLT_FGC0,		0x00},
++	{S1DREG_BBLT_FGC1,		0x00},
++	{S1DREG_LKUP_MODE,		0x00},	/* LCD LUT r | LCD and CRT/TV LUT w */
++	{S1DREG_LKUP_ADDR,		0x00},
++	{S1DREG_PS_CNF,			0x10},	/* Power Save disable */
++	{S1DREG_PS_STATUS,		0x02},	/* LCD Panel down, mem up */
++	{S1DREG_CPU2MEM_WDOGT,		0x00},
++	{S1DREG_COM_DISP_MODE,		0x02},	/* enable CRT display output */
++};
++
++static struct s1d13xxxfb_pdata ek_s1dfb_pdata = {
++	.initregs		= ek_s1dfb_initregs,
++	.initregssize		= ARRAY_SIZE(ek_s1dfb_initregs),
++	.platform_init_video	= ek_init_video,
++};
++
++static u64 s1dfb_dmamask = 0xffffffffUL;
++
++static struct resource ek_s1dfb_resource[] = {
++	[0] = {	/* video mem */
++		.name   = "s1d13806 memory",
++		.start  = AT91_FB_VMEM_BASE,
++		.end    = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1,
++		.flags  = IORESOURCE_MEM,
++	},
++	[1] = {	/* video registers */
++		.name   = "s1d13806 registers",
++		.start  = AT91_FB_REG_BASE,
++		.end    = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1,
++		.flags  = IORESOURCE_MEM,
++	},
++};
++
++static struct platform_device ek_s1dfb_device = {
++	.name		= "s1d13806fb",
++	.id		= -1,
++	.dev		= {
++			.dma_mask		= &s1dfb_dmamask,
++			.coherent_dma_mask	= 0xffffffff,
++			.platform_data		= &ek_s1dfb_pdata,
++	},
++	.resource	= ek_s1dfb_resource,
++	.num_resources	= ARRAY_SIZE(ek_s1dfb_resource),
++};
++
++static void __init ek_add_device_video(void)
++{
++	platform_device_register(&ek_s1dfb_device);
++}
++#else
++static void __init ek_add_device_video(void) {}
++#endif
++
+ static struct at91_eth_data __initdata ek_eth_data = {
+ 	.phy_irq_pin	= AT91_PIN_PC4,
+ 	.is_rmii	= 1,
+@@ -113,7 +294,7 @@
+ #define EK_FLASH_SIZE	0x200000
+ 
+ static struct physmap_flash_data ek_flash_data = {
+-	.width	= 2,
++	.width		= 2,
+ };
+ 
+ static struct resource ek_flash_resource = {
+@@ -132,6 +313,18 @@
+ 	.num_resources	= 1,
+ };
+ 
++static struct at91_gpio_led ek_leds[] = {
++	{
++		.name		= "led0",
++		.gpio		= AT91_PIN_PB1,
++		.trigger	= "heartbeat",
++	},
++	{
++		.name		= "led1",
++		.gpio		= AT91_PIN_PB2,
++		.trigger	= "timer",
++	}
++};
+ 
+ static void __init ek_board_init(void)
+ {
+@@ -158,8 +351,10 @@
+ #endif
+ 	/* NOR Flash */
+ 	platform_device_register(&ek_flash);
++	/* LEDs */
++	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+ 	/* VGA */
+-//	ek_add_device_video();
++	ek_add_device_video();
+ }
+ 
+ MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-kb9202.c linux-2.6-stable/arch/arm/mach-at91/board-kb9202.c
+--- linux-2.6.21/arch/arm/mach-at91/board-kb9202.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/board-kb9202.c	Tue May  8 12:21:31 2007
+@@ -37,6 +37,8 @@
+ #include <asm/arch/board.h>
+ #include <asm/arch/gpio.h>
+ 
++#include <asm/arch/at91rm9200_mc.h>
++
+ #include "generic.h"
+ 
+ 
+@@ -111,6 +113,48 @@
+ 	.partition_info	= nand_partitions,
+ };
+ 
++
++#if defined(CONFIG_FB_S1D15605)
++#warning "Rather pass reset pin via platform_data"
++static struct resource kb9202_lcd_resources[] = {
++	[0] = {
++		.start	= AT91_CHIPSELECT_2,
++		.end	= AT91_CHIPSELECT_2 + 0x200FF,
++		.flags	= IORESOURCE_MEM
++	},
++	[1] = {	/* reset pin */
++		.start	= AT91_PIN_PC22,
++		.end	= AT91_PIN_PC22,
++		.flags	= IORESOURCE_MEM
++	},
++};
++
++static struct platform_device kb9202_lcd_device = {
++	.name		= "s1d15605fb",
++	.id		= 0,
++	.num_resources	= ARRAY_SIZE(kb9202_lcd_resources),
++	.resource	= kb9202_lcd_resources,
++};
++
++static void __init kb9202_add_device_lcd(void)
++{
++ 	/* In case the boot loader did not set the chip select mode and timing */
++	at91_sys_write(AT91_SMC_CSR(2),
++		AT91_SMC_WSEN | AT91_SMC_NWS_(18) | AT91_SMC_TDF_(1) | AT91_SMC_DBW_8 |
++		AT91_SMC_RWSETUP_(1) | AT91_SMC_RWHOLD_(1));
++
++	/* Backlight pin = output, off */
++	at91_set_gpio_output(AT91_PIN_PC23, 0);
++
++	/* Reset pin = output, in reset */
++	at91_set_gpio_output(AT91_PIN_PC22, 0);
++
++	platform_device_register(&kb9202_lcd_device);
++}
++#else
++static void __init kb9202_add_device_lcd(void) {}
++#endif
++
+ static void __init kb9202_board_init(void)
+ {
+ 	/* Serial */
+@@ -129,6 +173,8 @@
+ 	at91_add_device_spi(NULL, 0);
+ 	/* NAND */
+ 	at91_add_device_nand(&kb9202_nand_data);
++	/* LCD	*/
++	kb9202_add_device_lcd();
+ }
+ 
+ MACHINE_START(KB9200, "KB920x")
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-sam9260ek.c linux-2.6-stable/arch/arm/mach-at91/board-sam9260ek.c
+--- linux-2.6.21/arch/arm/mach-at91/board-sam9260ek.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/board-sam9260ek.c	Tue May  8 12:13:30 2007
+@@ -104,9 +104,9 @@
+ 	},
+ #endif
+ #endif
+-#if defined(CONFIG_SND_AT73C213)
++#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
+ 	{	/* AT73C213 DAC */
+-		.modalias	= "snd_at73c213",
++		.modalias	= "at73c213",
+ 		.chip_select	= 0,
+ 		.max_speed_hz	= 10 * 1000 * 1000,
+ 		.bus_num	= 1,
+@@ -118,7 +118,7 @@
+ /*
+  * MACB Ethernet device
+  */
+-static struct __initdata at91_eth_data ek_macb_data = {
++static struct at91_eth_data __initdata ek_macb_data = {
+ 	.phy_irq_pin	= AT91_PIN_PA7,
+ 	.is_rmii	= 1,
+ };
+@@ -188,6 +188,8 @@
+ 	at91_add_device_eth(&ek_macb_data);
+ 	/* MMC */
+ 	at91_add_device_mmc(0, &ek_mmc_data);
++	/* I2C */
++	at91_add_device_i2c();
+ }
+ 
+ MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK")
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-sam9261ek.c linux-2.6-stable/arch/arm/mach-at91/board-sam9261ek.c
+--- linux-2.6.21/arch/arm/mach-at91/board-sam9261ek.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/board-sam9261ek.c	Wed May  9 12:37:19 2007
+@@ -25,7 +25,11 @@
+ #include <linux/module.h>
+ #include <linux/platform_device.h>
+ #include <linux/spi/spi.h>
++#include <linux/spi/ads7846.h>
+ #include <linux/dm9000.h>
++#include <linux/fb.h>
++
++#include <video/atmel_lcdc.h>
+ 
+ #include <asm/hardware.h>
+ #include <asm/setup.h>
+@@ -59,6 +63,9 @@
+ 	/* Initialize processor: 18.432 MHz crystal */
+ 	at91sam9261_initialize(18432000);
+ 
++	/* Setup the LEDs */
++	at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
++
+ 	/* Setup the serial ports and console */
+ 	at91_init_serial(&ek_uart_config);
+ }
+@@ -195,6 +202,41 @@
+ };
+ 
+ /*
++ * ADS7846 Touchscreen
++ */
++#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
++
++static int ads7843_pendown_state(void)
++{
++	return !at91_get_gpio_value(AT91_PIN_PC2);	/* Touchscreen PENIRQ */
++}
++
++static struct ads7846_platform_data ads_info = {
++	.model			= 7843,
++	.x_min			= 150,
++	.x_max			= 3830,
++	.y_min			= 190,
++	.y_max			= 3830,
++	.vref_delay_usecs	= 100,
++	.x_plate_ohms		= 450,
++	.y_plate_ohms		= 250,
++	.pressure_max		= 15000,
++	.debounce_max		= 1,
++	.debounce_rep		= 0,
++	.debounce_tol		= (~0),
++	.get_pendown_state	= ads7843_pendown_state,
++};
++
++static void __init ek_add_device_ts(void)
++{
++	at91_set_B_periph(AT91_PIN_PC2, 1);	/* External IRQ0, with pullup */
++	at91_set_gpio_input(AT91_PIN_PA11, 1);	/* Touchscreen BUSY signal */
++}
++#else
++static void __init ek_add_device_ts(void) {}
++#endif
++
++/*
+  * SPI devices
+  */
+ static struct spi_board_info ek_spi_devices[] = {
+@@ -204,6 +246,17 @@
+ 		.max_speed_hz	= 15 * 1000 * 1000,
+ 		.bus_num	= 0,
+ 	},
++#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
++	{
++		.modalias	= "ads7846",
++		.chip_select	= 2,
++		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
++		.bus_num	= 0,
++		.platform_data	= &ads_info,
++		.irq		= AT91SAM9261_ID_IRQ0,
++		.controller_data = AT91_PIN_PA28,	/* CS pin */
++	},
++#endif
+ #if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+ 	{	/* DataFlash card - jumper (J12) configurable to CS3 or CS0 */
+ 		.modalias	= "mtd_dataflash",
+@@ -211,9 +264,9 @@
+ 		.max_speed_hz	= 15 * 1000 * 1000,
+ 		.bus_num	= 0,
+ 	},
+-#elif defined(CONFIG_SND_AT73C213)
++#elif defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
+ 	{	/* AT73C213 DAC */
+-		.modalias	= "snd_at73c213",
++		.modalias	= "at73c213",
+ 		.chip_select	= 3,
+ 		.max_speed_hz	= 10 * 1000 * 1000,
+ 		.bus_num	= 0,
+@@ -222,6 +275,65 @@
+ };
+ 
+ 
++/*
++ * LCD Controller
++ */
++#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
++static struct fb_videomode at91_tft_vga_modes[] = {
++	{
++	        .name           = "TX09D50VM1CCA @ 60",
++		.refresh	= 60,
++		.xres		= 240,		.yres		= 320,
++		.pixclock	= KHZ2PICOS(4965),
++
++		.left_margin	= 1,		.right_margin	= 33,
++		.upper_margin	= 1,		.lower_margin	= 0,
++		.hsync_len	= 5,		.vsync_len	= 1,
++
++		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
++		.vmode		= FB_VMODE_NONINTERLACED,
++	},
++};
++
++static struct fb_monspecs at91fb_default_monspecs = {
++	.manufacturer	= "HIT",
++	.monitor        = "TX09D50VM1CCA",
++
++	.modedb		= at91_tft_vga_modes,
++	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
++	.hfmin		= 15000,
++	.hfmax		= 64000,
++	.vfmin		= 50,
++	.vfmax		= 150,
++};
++
++#define AT91SAM9261_DEFAULT_LCDCON2 	(ATMEL_LCDC_MEMOR_LITTLE \
++					| ATMEL_LCDC_DISTYPE_TFT    \
++					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
++
++static void at91_lcdc_power_control(int on)
++{
++	if (on)
++		at91_set_gpio_value(AT91_PIN_PA12, 0);	/* power up */
++	else
++		at91_set_gpio_value(AT91_PIN_PA12, 1);	/* power down */
++}
++
++/* Driver datas */
++static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
++	.default_bpp			= 16,
++	.default_dmacon			= ATMEL_LCDC_DMAEN,
++	.default_lcdcon2		= AT91SAM9261_DEFAULT_LCDCON2,
++	.default_monspecs		= &at91fb_default_monspecs,
++	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
++	.guard_time			= 1,
++};
++
++#else
++static struct atmel_lcdfb_info __initdata ek_lcdc_data;
++#endif
++
++
+ static void __init ek_board_init(void)
+ {
+ 	/* Serial */
+@@ -241,10 +353,14 @@
+ #if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+ 	/* SPI */
+ 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
++	/* Touchscreen */
++	ek_add_device_ts();
+ #else
+ 	/* MMC */
+ 	at91_add_device_mmc(0, &ek_mmc_data);
+ #endif
++	/* LCD Controller */
++	at91_add_device_lcdc(&ek_lcdc_data);
+ }
+ 
+ MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK")
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-sam9263ek.c linux-2.6-stable/arch/arm/mach-at91/board-sam9263ek.c
+--- linux-2.6.21/arch/arm/mach-at91/board-sam9263ek.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/board-sam9263ek.c	Tue May  8 12:56:33 2007
+@@ -25,6 +25,10 @@
+ #include <linux/module.h>
+ #include <linux/platform_device.h>
+ #include <linux/spi/spi.h>
++#include <linux/spi/ads7846.h>
++#include <linux/fb.h>
++
++#include <video/atmel_lcdc.h>
+ 
+ #include <asm/hardware.h>
+ #include <asm/setup.h>
+@@ -86,6 +90,40 @@
+ 
+ 
+ /*
++ * ADS7846 Touchscreen
++ */
++#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
++static int ads7843_pendown_state(void)
++{
++	return !at91_get_gpio_value(AT91_PIN_PA15);	/* Touchscreen PENIRQ */
++}
++
++static struct ads7846_platform_data ads_info = {
++	.model			= 7843,
++	.x_min			= 150,
++	.x_max			= 3830,
++	.y_min			= 190,
++	.y_max			= 3830,
++	.vref_delay_usecs	= 100,
++	.x_plate_ohms		= 450,
++	.y_plate_ohms		= 250,
++	.pressure_max		= 15000,
++	.debounce_max		= 1,
++	.debounce_rep		= 0,
++	.debounce_tol		= (~0),
++	.get_pendown_state	= ads7843_pendown_state,
++};
++
++static void __init ek_add_device_ts(void)
++{
++	at91_set_B_periph(AT91_PIN_PA15, 1);	/* External IRQ1, with pullup */
++	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* Touchscreen BUSY signal */
++}
++#else
++static void __init ek_add_device_ts(void) {}
++#endif
++
++/*
+  * SPI devices.
+  */
+ static struct spi_board_info ek_spi_devices[] = {
+@@ -97,6 +135,16 @@
+ 		.bus_num	= 0,
+ 	},
+ #endif
++#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
++	{
++		.modalias	= "ads7846",
++		.chip_select	= 3,
++		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
++		.bus_num	= 0,
++		.platform_data	= &ads_info,
++		.irq		= AT91SAM9263_ID_IRQ1,
++	},
++#endif
+ };
+ 
+ 
+@@ -112,6 +160,14 @@
+ 
+ 
+ /*
++ * MACB Ethernet device
++ */
++static struct at91_eth_data __initdata ek_macb_data = {
++	.is_rmii	= 1,
++};
++
++
++/*
+  * NAND flash
+  */
+ static struct mtd_partition __initdata ek_nand_partition[] = {
+@@ -148,6 +204,73 @@
+ };
+ 
+ 
++/*
++ * LCD Controller
++ */
++#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
++static struct fb_videomode at91_tft_vga_modes[] = {
++	{
++	        .name           = "TX09D50VM1CCA @ 60",
++		.refresh	= 60,
++		.xres		= 240,		.yres		= 320,
++		.pixclock	= KHZ2PICOS(4965),
++
++		.left_margin	= 1,		.right_margin	= 33,
++		.upper_margin	= 1,		.lower_margin	= 0,
++		.hsync_len	= 5,		.vsync_len	= 1,
++
++		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
++		.vmode		= FB_VMODE_NONINTERLACED,
++	},
++};
++
++static struct fb_monspecs at91fb_default_monspecs = {
++	.manufacturer	= "HIT",
++	.monitor        = "TX09D70VM1CCA",
++
++	.modedb		= at91_tft_vga_modes,
++	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
++	.hfmin		= 15000,
++	.hfmax		= 64000,
++	.vfmin		= 50,
++	.vfmax		= 150,
++};
++
++#define AT91SAM9263_DEFAULT_LCDCON2 	(ATMEL_LCDC_MEMOR_LITTLE \
++					| ATMEL_LCDC_DISTYPE_TFT    \
++					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
++
++static void at91_lcdc_power_control(int on)
++{
++	if (on)
++		at91_set_gpio_value(AT91_PIN_PD12, 0);	/* power up */
++	else
++		at91_set_gpio_value(AT91_PIN_PD12, 1);	/* power down */
++}
++
++/* Driver datas */
++static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
++	.default_bpp			= 16,
++	.default_dmacon			= ATMEL_LCDC_DMAEN,
++	.default_lcdcon2		= AT91SAM9263_DEFAULT_LCDCON2,
++	.default_monspecs		= &at91fb_default_monspecs,
++	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
++	.guard_time			= 1,
++};
++
++#else
++static struct atmel_lcdfb_info __initdata ek_lcdc_data;
++#endif
++
++
++/*
++ * AC97
++ */
++static struct atmel_ac97_data ek_ac97_data = {
++	.reset_pin	= AT91_PIN_PA13,
++};
++
++
+ static void __init ek_board_init(void)
+ {
+ 	/* Serial */
+@@ -157,11 +280,22 @@
+ 	/* USB Device */
+ 	at91_add_device_udc(&ek_udc_data);
+ 	/* SPI */
++	at91_set_gpio_output(AT91_PIN_PE20, 1);		/* select spi0 clock */
+ 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
++	/* Touchscreen */
++	ek_add_device_ts();
+ 	/* MMC */
+ 	at91_add_device_mmc(1, &ek_mmc_data);
++	/* Ethernet */
++	at91_add_device_eth(&ek_macb_data);
+ 	/* NAND */
+ 	at91_add_device_nand(&ek_nand_data);
++	/* I2C */
++	at91_add_device_i2c();
++	/* LCD Controller */
++	at91_add_device_lcdc(&ek_lcdc_data);
++	/* AC97 */
++	at91_add_device_ac97(&ek_ac97_data);
+ }
+ 
+ MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/board-sam9rlek.c linux-2.6-stable/arch/arm/mach-at91/board-sam9rlek.c
+--- linux-2.6.21/arch/arm/mach-at91/board-sam9rlek.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/board-sam9rlek.c	Wed May  9 10:58:34 2007
+@@ -0,0 +1,204 @@
++/*
++ *  Copyright (C) 2005 SAN People
++ *  Copyright (C) 2007 Atmel Corporation
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file COPYING in the main directory of this archive for
++ * more details.
++ */
++
++#include <linux/types.h>
++#include <linux/init.h>
++#include <linux/mm.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/spi/spi.h>
++#include <linux/fb.h>
++#include <linux/clk.h>
++
++#include <video/atmel_lcdc.h>
++
++#include <asm/hardware.h>
++#include <asm/setup.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/mach/irq.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++#include <asm/arch/at91sam926x_mc.h>
++
++#include "generic.h"
++
++
++/*
++ * Serial port configuration.
++ *    0 .. 3 = USART0 .. USART3
++ *    4      = DBGU
++ */
++static struct at91_uart_config __initdata ek_uart_config = {
++	.console_tty	= 0,				/* ttyS0 */
++	.nr_tty		= 2,
++	.tty_map	= { 4, 0, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
++};
++
++static void __init ek_map_io(void)
++{
++	/* Initialize processor: 12.000 MHz crystal */
++	at91sam9rl_initialize(12000000);
++
++	/* Setup the serial ports and console */
++	at91_init_serial(&ek_uart_config);
++}
++
++static void __init ek_init_irq(void)
++{
++	at91sam9rl_init_interrupts(NULL);
++}
++
++
++/*
++ * MCI (SD/MMC)
++ */
++static struct at91_mmc_data __initdata ek_mmc_data = {
++	.wire4		= 1,
++	.det_pin	= AT91_PIN_PA15,
++//	.wp_pin		= ... not connected
++//	.vcc_pin	= ... not connected
++};
++
++
++/*
++ * NAND flash
++ */
++static struct mtd_partition __initdata ek_nand_partition[] = {
++	{
++		.name	= "Partition 1",
++		.offset	= 0,
++		.size	= 256 * 1024,
++	},
++	{
++		.name	= "Partition 2",
++		.offset	= 256 * 1024 ,
++		.size	= MTDPART_SIZ_FULL,
++	},
++};
++
++static struct mtd_partition *nand_partitions(int size, int *num_partitions)
++{
++	*num_partitions = ARRAY_SIZE(ek_nand_partition);
++	return ek_nand_partition;
++}
++
++static struct at91_nand_data __initdata ek_nand_data = {
++	.ale		= 21,
++	.cle		= 22,
++//	.det_pin	= ... not connected
++	.rdy_pin	= AT91_PIN_PD17,
++	.enable_pin	= AT91_PIN_PB6,
++	.partition_info	= nand_partitions,
++	.bus_width_16	= 0,
++};
++
++
++/*
++ * SPI devices
++ */
++static struct spi_board_info ek_spi_devices[] = {
++	{	/* DataFlash chip */
++		.modalias	= "mtd_dataflash",
++		.chip_select	= 0,
++		.max_speed_hz	= 15 * 1000 * 1000,
++		.bus_num	= 0,
++	},
++};
++
++
++/*
++ * LCD Controller
++ */
++#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
++static struct fb_videomode at91_tft_vga_modes[] = {
++	{
++		.name		= "TX09D50VM1CCA @ 60",
++		.refresh	= 60,
++		.xres		= 240,		.yres		= 320,
++		.pixclock	= KHZ2PICOS(4965),
++
++		.left_margin	= 1,		.right_margin	= 33,
++		.upper_margin	= 1,		.lower_margin	= 0,
++		.hsync_len	= 5,		.vsync_len	= 1,
++
++		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
++		.vmode		= FB_VMODE_NONINTERLACED,
++	},
++};
++
++static struct fb_monspecs at91fb_default_monspecs = {
++	.manufacturer	= "HIT",
++	.monitor	= "TX09D50VM1CCA",
++
++	.modedb		= at91_tft_vga_modes,
++	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
++	.hfmin		= 15000,
++	.hfmax		= 64000,
++	.vfmin		= 50,
++	.vfmax		= 150,
++};
++
++#define AT91SAM9RL_DEFAULT_LCDCON2	(ATMEL_LCDC_MEMOR_LITTLE \
++					| ATMEL_LCDC_DISTYPE_TFT \
++					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
++
++static void at91_lcdc_power_control(int on)
++{
++	if (on)
++		at91_set_gpio_value(AT91_PIN_PA30, 0);	/* power up */
++	else
++		at91_set_gpio_value(AT91_PIN_PA30, 1);	/* power down */
++}
++
++/* Driver datas */
++static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
++	.default_bpp			= 16,
++	.default_dmacon			= ATMEL_LCDC_DMAEN,
++	.default_lcdcon2		= AT91SAM9RL_DEFAULT_LCDCON2,
++	.default_monspecs		= &at91fb_default_monspecs,
++	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
++	.guard_time			= 1,
++};
++
++#else
++static struct atmel_lcdfb_info __initdata ek_lcdc_data;
++#endif
++
++
++static void __init ek_board_init(void)
++{
++	/* Serial */
++	at91_add_device_serial();
++	/* I2C */
++	at91_add_device_i2c();
++	/* NAND */
++	at91_add_device_nand(&ek_nand_data);
++	/* SPI */
++	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
++	/* MMC */
++	at91_add_device_mmc(0, &ek_mmc_data);
++	/* LCD Controller */
++	at91_add_device_lcdc(&ek_lcdc_data);
++}
++
++MACHINE_START(AT91SAM9RLEK, "Atmel AT91SAM9RL-EK")
++	/* Maintainer: Atmel */
++	.phys_io	= AT91_BASE_SYS,
++	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
++	.boot_params	= AT91_SDRAM_BASE + 0x100,
++	.timer		= &at91sam926x_timer,
++	.map_io		= ek_map_io,
++	.init_irq	= ek_init_irq,
++	.init_machine	= ek_board_init,
++MACHINE_END
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/clock.c linux-2.6-stable/arch/arm/mach-at91/clock.c
+--- linux-2.6.21/arch/arm/mach-at91/clock.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/clock.c	Tue May  8 12:13:30 2007
+@@ -32,6 +32,7 @@
+ #include <asm/arch/cpu.h>
+ 
+ #include "clock.h"
++#include "generic.h"
+ 
+ 
+ /*
+@@ -254,6 +255,23 @@
+ 
+ /*------------------------------------------------------------------------*/
+ 
++#ifdef CONFIG_PM
++
++int clk_must_disable(struct clk *clk)
++{
++	if (!at91_suspend_entering_slow_clock())
++		return 0;
++
++	while (clk->parent)
++		clk = clk->parent;
++	return clk != &clk32k;
++}
++EXPORT_SYMBOL(clk_must_disable);
++
++#endif
++
++/*------------------------------------------------------------------------*/
++
+ #ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
+ 
+ /*
+@@ -375,6 +393,7 @@
+ 	seq_printf(s, "PLLB = %8x\n", at91_sys_read(AT91_CKGR_PLLBR));
+ 
+ 	seq_printf(s, "MCKR = %8x\n", at91_sys_read(AT91_PMC_MCKR));
++#warning "Hard-coded PCK"
+ 	for (i = 0; i < 4; i++)
+ 		seq_printf(s, "PCK%d = %8x\n", i, at91_sys_read(AT91_PMC_PCKR(i)));
+ 	seq_printf(s, "SR   = %8x\n", sr = at91_sys_read(AT91_PMC_SR));
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/generic.h linux-2.6-stable/arch/arm/mach-at91/generic.h
+--- linux-2.6.21/arch/arm/mach-at91/generic.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/generic.h	Wed May  9 10:20:54 2007
+@@ -13,12 +13,14 @@
+ extern void __init at91sam9260_initialize(unsigned long main_clock);
+ extern void __init at91sam9261_initialize(unsigned long main_clock);
+ extern void __init at91sam9263_initialize(unsigned long main_clock);
++extern void __init at91sam9rl_initialize(unsigned long main_clock);
+ 
+  /* Interrupts */
+ extern void __init at91rm9200_init_interrupts(unsigned int priority[]);
+ extern void __init at91sam9260_init_interrupts(unsigned int priority[]);
+ extern void __init at91sam9261_init_interrupts(unsigned int priority[]);
+ extern void __init at91sam9263_init_interrupts(unsigned int priority[]);
++extern void __init at91sam9rl_init_interrupts(unsigned int priority[]);
+ extern void __init at91_aic_init(unsigned int priority[]);
+ 
+  /* Timer */
+@@ -34,6 +36,7 @@
+  /* Power Management */
+ extern void at91_irq_suspend(void);
+ extern void at91_irq_resume(void);
++extern int at91_suspend_entering_slow_clock(void);
+ 
+  /* GPIO */
+ #define AT91RM9200_PQFP		3	/* AT91RM9200 PQFP package has 3 banks */
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/ics1523.c linux-2.6-stable/arch/arm/mach-at91/ics1523.c
+--- linux-2.6.21/arch/arm/mach-at91/ics1523.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/ics1523.c	Tue May  8 12:13:30 2007
+@@ -0,0 +1,207 @@
++/*
++ * arch/arm/mach-at91rm9200/ics1523.c
++ *
++ *  Copyright (C) 2003 ATMEL Rousset
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++
++#include <asm/hardware.h>
++#include <asm/io.h>
++
++#include <linux/clk.h>
++#include <linux/delay.h>
++#include <linux/err.h>
++#include <linux/init.h>
++
++#include <asm/arch/ics1523.h>
++#include <asm/arch/at91_twi.h>
++#include <asm/arch/gpio.h>
++
++/* TWI Errors */
++#define	AT91_TWI_ERROR	(AT91_TWI_NACK | AT91_TWI_UNRE | AT91_TWI_OVRE)
++
++
++static void __iomem *twi_base;
++
++#define at91_twi_read(reg)		__raw_readl(twi_base + (reg))
++#define at91_twi_write(reg, val)	__raw_writel((val), twi_base + (reg))
++
++
++/* -----------------------------------------------------------------------------
++ * Initialization of TWI CLOCK
++ * ----------------------------------------------------------------------------- */
++
++static void at91_ics1523_SetTwiClock(unsigned int mck_khz)
++{
++	int sclock;
++
++	/* Here, CKDIV = 1 and CHDIV = CLDIV  ==> CLDIV = CHDIV = 1/4*((Fmclk/FTWI) -6) */
++	sclock = (10*mck_khz / ICS_TRANSFER_RATE);
++	if (sclock % 10 >= 5)
++		sclock = (sclock /10) - 5;
++	else
++		sclock = (sclock /10)- 6;
++	sclock = (sclock + (4 - sclock %4)) >> 2;	/* div 4 */
++
++	at91_twi_write(AT91_TWI_CWGR, 0x00010000 | sclock | (sclock << 8));
++}
++
++/* -----------------------------------------------------------------------------
++ * Read a byte with TWI Interface from the Clock Generator ICS1523
++ * ----------------------------------------------------------------------------- */
++
++static int at91_ics1523_ReadByte(unsigned char reg_address, unsigned char *data_in)
++{
++	int Status, nb_trial;
++
++	at91_twi_write(AT91_TWI_MMR, AT91_TWI_MREAD | AT91_TWI_IADRSZ_1 | ((ICS_ADDR << 16) & AT91_TWI_DADR));
++	at91_twi_write(AT91_TWI_IADR, reg_address);
++	at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP);
++
++	/* Program temporizing period (300us) */
++	udelay(300);
++
++	/* Wait TXcomplete ... */
++	nb_trial = 0;
++	Status = at91_twi_read(AT91_TWI_SR);
++	while (!(Status & AT91_TWI_TXCOMP) && (nb_trial < 10)) {
++		nb_trial++;
++		Status = at91_twi_read(AT91_TWI_SR);
++	}
++
++	if (Status & AT91_TWI_TXCOMP) {
++		*data_in = (unsigned char) at91_twi_read(AT91_TWI_RHR);
++		return ICS1523_ACCESS_OK;
++	}
++	else
++		return ICS1523_ACCESS_ERROR;
++}
++
++/* -----------------------------------------------------------------------------
++ * Write a byte with TWI Interface to the Clock Generator ICS1523
++ * ----------------------------------------------------------------------------- */
++
++static int at91_ics1523_WriteByte(unsigned char reg_address, unsigned char data_out)
++{
++	int Status, nb_trial;
++
++	at91_twi_write(AT91_TWI_MMR, AT91_TWI_IADRSZ_1 | ((ICS_ADDR << 16) & AT91_TWI_DADR));
++	at91_twi_write(AT91_TWI_IADR, reg_address);
++	at91_twi_write(AT91_TWI_THR, data_out);
++	at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP);
++
++	/* Program temporizing period (300us) */
++	udelay(300);
++
++	nb_trial = 0;
++	Status = at91_twi_read(AT91_TWI_SR);
++	while (!(Status & AT91_TWI_TXCOMP) && (nb_trial < 10)) {
++		nb_trial++;
++		if (Status & AT91_TWI_ERROR) {
++			/* If Underrun OR NACK - Start again */
++			at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP);
++
++			/*  Program temporizing period (300us) */
++			udelay(300);
++		}
++		Status = at91_twi_read(AT91_TWI_SR);
++	};
++
++	if (Status & AT91_TWI_TXCOMP)
++		return ICS1523_ACCESS_OK;
++	else
++		return ICS1523_ACCESS_ERROR;
++}
++
++/* -----------------------------------------------------------------------------
++ * Initialization of the Clock Generator ICS1523
++ * ----------------------------------------------------------------------------- */
++
++int at91_ics1523_init(void)
++{
++	int		nb_trial;
++	int		ack = ICS1523_ACCESS_OK;
++	unsigned int	status = 0xffffffff;
++	struct clk	*twi_clk;
++
++	/* Map in TWI peripheral */
++	twi_base = ioremap(AT91RM9200_BASE_TWI, SZ_16K);
++	if (!twi_base)
++		return -ENOMEM;
++
++	/* pins used for TWI interface */
++	at91_set_A_periph(AT91_PIN_PA25, 0);            /* TWD */
++	at91_set_multi_drive(AT91_PIN_PA25, 1);
++	at91_set_A_periph(AT91_PIN_PA26, 0);            /* TWCK */
++	at91_set_multi_drive(AT91_PIN_PA26, 1);
++
++	/* Enable the TWI clock */
++	twi_clk = clk_get(NULL, "twi_clk");
++	if (IS_ERR(twi_clk))
++		return ICS1523_ACCESS_ERROR;
++	clk_enable(twi_clk);
++
++	/* Disable interrupts */
++	at91_twi_write(AT91_TWI_IDR, -1);
++
++	/* Reset peripheral */
++	at91_twi_write(AT91_TWI_CR, AT91_TWI_SWRST);
++
++	/* Set Master mode */
++	at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN);
++
++	/* Set TWI Clock Waveform Generator Register */
++	at91_ics1523_SetTwiClock(60000);     /* MCK in KHz = 60000 KHz */
++
++	/* ICS1523 Initialisation */
++	ack |= at91_ics1523_WriteByte ((unsigned char) ICS_ICR, (unsigned char) 0);
++	ack |= at91_ics1523_WriteByte ((unsigned char) ICS_OE, (unsigned char) (ICS_OEF | ICS_OET2 | ICS_OETCK));
++	ack |= at91_ics1523_WriteByte ((unsigned char) ICS_OD, (unsigned char) (ICS_INSEL | 0x7F));
++	ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAO, (unsigned char) 0);
++
++	nb_trial = 0;
++	do {
++		nb_trial++;
++		ack |= at91_ics1523_WriteByte ((unsigned char) ICS_ICR, (unsigned char) (ICS_ENDLS | ICS_ENPLS | ICS_PDEN /*| ICS_FUNCSEL*/));
++		ack |= at91_ics1523_WriteByte ((unsigned char) ICS_LCR, (unsigned char) (ICS_PSD | ICS_PFD));
++		ack |= at91_ics1523_WriteByte ((unsigned char) ICS_FD0, (unsigned char) 0x39) ; /* 0x7A */
++		ack |= at91_ics1523_WriteByte ((unsigned char) ICS_FD1, (unsigned char) 0x00);
++		ack |= at91_ics1523_WriteByte ((unsigned char) ICS_SWRST, (unsigned char) (ICS_PLLR));
++
++		/* Program 1ms temporizing period */
++		mdelay(1);
++
++		at91_ics1523_ReadByte ((unsigned char) ICS_SR, (char *)&status);
++	} while (!((unsigned int) status & (unsigned int) ICS_PLLLOCK) && (nb_trial < 10));
++
++	ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAC, (unsigned char) 0x03) ; /* 0x01 */
++	ack |= at91_ics1523_WriteByte ((unsigned char) ICS_SWRST, (unsigned char) (ICS_DPAR));
++
++	/* Program 1ms temporizing period */
++	mdelay(1);
++
++	ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAO, (unsigned char) 0x00);
++
++	/* Program 1ms temporizing period */
++	mdelay(1);
++	
++	/* All done - cleanup */
++	iounmap(twi_base);
++	clk_disable(twi_clk);
++	clk_put(twi_clk);
++
++	return ack;
++}
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/pm.c linux-2.6-stable/arch/arm/mach-at91/pm.c
+--- linux-2.6.21/arch/arm/mach-at91/pm.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mach-at91/pm.c	Tue May  8 12:13:31 2007
+@@ -63,6 +63,7 @@
+  * Verify that all the clocks are correct before entering
+  * slow-clock mode.
+  */
++#warning "SAM9260 only has 3 programmable clocks."
+ static int at91_pm_verify_clocks(void)
+ {
+ 	unsigned long scsr;
+@@ -104,20 +105,15 @@
+ }
+ 
+ /*
+- * Call this from platform driver suspend() to see how deeply to suspend.
++ * This is called from clk_must_disable(), to see how deeply to suspend.
+  * For example, some controllers (like OHCI) need one of the PLL clocks
+  * in order to act as a wakeup source, and those are not available when
+  * going into slow clock mode.
+- *
+- * REVISIT: generalize as clk_will_be_available(clk)?  Other platforms have
+- * the very same problem (but not using at91 main_clk), and it'd be better
+- * to add one generic API rather than lots of platform-specific ones.
+  */
+ int at91_suspend_entering_slow_clock(void)
+ {
+ 	return (target_state == PM_SUSPEND_MEM);
+ }
+-EXPORT_SYMBOL(at91_suspend_entering_slow_clock);
+ 
+ 
+ static void (*slow_clock)(void);
+@@ -207,16 +203,23 @@
+ 	.enter		= at91_pm_enter,
+ };
+ 
++#ifdef CONFIG_AT91_SLOW_CLOCK
++extern void at91rm9200_slow_clock(void);
++extern u32 at91rm9200_slow_clock_sz;
++#endif
++
+ static int __init at91_pm_init(void)
+ {
+-	printk("AT91: Power Management\n");
+-
+-#ifdef CONFIG_AT91_PM_SLOW_CLOCK
+-	/* REVISIT allocations of SRAM should be dynamically managed.
++#ifdef CONFIG_AT91_SLOW_CLOCK
++	/*
++	 * REVISIT allocations of SRAM should be dynamically managed.
+ 	 * FIQ handlers and other components will want SRAM/TCM too...
+ 	 */
+-	slow_clock = (void *) (AT91_VA_BASE_SRAM + (3 * SZ_4K));
++	slow_clock = (void *) (AT91_IO_VIRT_BASE - AT91RM9200_SRAM_SIZE + (3 * SZ_4K));
+ 	memcpy(slow_clock, at91rm9200_slow_clock, at91rm9200_slow_clock_sz);
++	printk("AT91: Power Management (with slow clock mode)\n");
++#else
++	printk("AT91: Power Management\n");
+ #endif
+ 
+ 	/* Disable SDRAM low-power mode.  Cannot be used with self-refresh. */
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/pm_slowclock.S linux-2.6-stable/arch/arm/mach-at91/pm_slowclock.S
+--- linux-2.6.21/arch/arm/mach-at91/pm_slowclock.S	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/pm_slowclock.S	Tue May  8 12:13:31 2007
+@@ -0,0 +1,172 @@
++/*
++ * arch/arm/mach-at91/pm_slow_clock.S
++ *
++ *  Copyright (C) 2006 Savin Zlobec
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/linkage.h>
++#include <asm/hardware.h>
++#include <asm/arch/at91_pmc.h>
++#include <asm/arch/at91rm9200_mc.h>
++
++#define MCKRDY_TIMEOUT		1000
++#define MOSCRDY_TIMEOUT 	1000
++#define PLLALOCK_TIMEOUT	1000
++
++	.macro wait_mckrdy
++	mov	r2, #MCKRDY_TIMEOUT
++1:	sub	r2, r2, #1
++	cmp	r2, #0
++	beq	2f
++	ldr	r3, [r1, #AT91_PMC_SR]
++	tst	r3, #AT91_PMC_MCKRDY
++	beq	1b
++2:
++	.endm
++
++	.macro wait_moscrdy
++	mov	r2, #MOSCRDY_TIMEOUT
++1:	sub	r2, r2, #1
++	cmp	r2, #0
++	beq	2f
++	ldr	r3, [r1, #AT91_PMC_SR]
++	tst	r3, #AT91_PMC_MOSCS
++	beq	1b
++2:
++	.endm
++
++	.macro wait_pllalock
++	mov	r2, #PLLALOCK_TIMEOUT
++1:	sub	r2, r2, #1
++	cmp	r2, #0
++	beq	2f
++	ldr	r3, [r1, #AT91_PMC_SR]
++	tst	r3, #AT91_PMC_LOCKA
++	beq	1b
++2:
++	.endm
++
++	.macro wait_plladis
++	mov	r2, #PLLALOCK_TIMEOUT
++1:	sub	r2, r2, #1
++	cmp	r2, #0
++	beq	2f
++	ldr	r3, [r1, #AT91_PMC_SR]
++	tst	r3, #AT91_PMC_LOCKA
++	bne	1b
++2:
++	.endm
++
++	.text
++
++ENTRY(at91rm9200_slow_clock)
++
++	ldr	r1, .at91_va_base_sys
++
++	/* Put SDRAM in self refresh mode */
++
++	b	1f
++	.align	5
++1:	mcr	p15, 0, r0, c7, c10, 4
++	mov	r2, #1
++	str	r2, [r1, #AT91_SDRAMC_SRR]
++
++	/* Save Master clock setting */
++
++	ldr	r2, [r1, #AT91_PMC_MCKR]
++	str	r2, .saved_mckr
++
++	/*
++	 * Set the Master clock source to slow clock
++	 *
++	 * First set the CSS field, wait for MCKRDY
++	 * and than set the PRES and MDIV fields.
++	 *
++	 * See eratta #2[78] for details.
++	 */
++
++	bic	r2, r2, #3
++	str	r2, [r1, #AT91_PMC_MCKR]
++
++	wait_mckrdy
++
++	mov	r2, #0
++	str	r2, [r1, #AT91_PMC_MCKR]
++
++	/* Save PLLA setting and disable it */
++
++	ldr	r2, [r1, #AT91_CKGR_PLLAR]
++	str	r2, .saved_pllar
++
++	mov	r2, #0
++	str	r2, [r1, #AT91_CKGR_PLLAR]
++
++	wait_plladis
++
++	/* Turn off the main oscillator */
++
++	ldr	r2, [r1, #AT91_CKGR_MOR]
++	bic	r2, r2, #AT91_PMC_MOSCEN
++	str	r2, [r1, #AT91_CKGR_MOR]
++
++	/* Wait for interrupt */
++
++	mcr	p15, 0, r0, c7, c0, 4
++
++	/* Turn on the main oscillator */
++
++	ldr	r2, [r1, #AT91_CKGR_MOR]
++	orr	r2, r2, #AT91_PMC_MOSCEN
++	str	r2, [r1, #AT91_CKGR_MOR]
++
++	wait_moscrdy
++
++	/* Restore PLLA setting */
++
++	ldr	r2, .saved_pllar
++	str	r2, [r1, #AT91_CKGR_PLLAR]
++
++	wait_pllalock
++
++	/*
++	 * Restore master clock setting
++	 *
++	 * First set PRES if it was not 0,
++	 * than set CSS and MDIV fields.
++	 * After every change wait for
++	 * MCKRDY.
++	 *
++	 * See eratta #2[78] for details.
++	 */
++
++	ldr	r2, .saved_mckr
++	tst	r2, #0x1C
++	beq	2f
++	and	r2, r2, #0x1C
++	str	r2, [r1, #AT91_PMC_MCKR]
++
++	wait_mckrdy
++
++2:	ldr	r2, .saved_mckr
++	str	r2, [r1, #AT91_PMC_MCKR]
++
++	wait_mckrdy
++
++	mov	pc, lr
++
++.saved_mckr:
++	.word 0
++
++.saved_pllar:
++	.word 0
++
++.at91_va_base_sys:
++	.word AT91_VA_BASE_SYS
++
++ENTRY(at91rm9200_slow_clock_sz)
++	.word .-at91rm9200_slow_clock
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/tclib.c linux-2.6-stable/arch/arm/mach-at91/tclib.c
+--- linux-2.6.21/arch/arm/mach-at91/tclib.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/tclib.c	Tue May  8 12:13:31 2007
+@@ -0,0 +1,17 @@
++#include <linux/clk.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++
++#include "tclib.h"
++
++static struct atmel_tcblock *blocks;
++static int nblocks;
++
++/*
++ * Called from the processor-specific init to register the TC Blocks.
++ */
++void __init atmel_tc_init(struct atmel_tcblock *tcblocks, int n)
++{
++	blocks = tcblocks;
++	nblocks = n;
++}
+diff -urN -x CVS linux-2.6.21/arch/arm/mach-at91/tclib.h linux-2.6-stable/arch/arm/mach-at91/tclib.h
+--- linux-2.6.21/arch/arm/mach-at91/tclib.h	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/arch/arm/mach-at91/tclib.h	Tue May  8 12:13:31 2007
+@@ -0,0 +1,11 @@
++
++#define TC_PER_TCB	3
++
++struct atmel_tcblock {
++	u32 		physaddr;
++	void __iomem	*ioaddr;
++	struct clk	*clk[TC_PER_TCB];
++	int		irq[TC_PER_TCB];
++};
++
++extern void __init atmel_tc_init(struct atmel_tcblock *tcblocks, int n);
+diff -urN -x CVS linux-2.6.21/arch/arm/mm/Kconfig linux-2.6-stable/arch/arm/mm/Kconfig
+--- linux-2.6.21/arch/arm/mm/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/mm/Kconfig	Wed May  9 10:20:54 2007
+@@ -171,8 +171,8 @@
+ # ARM926T
+ config CPU_ARM926T
+ 	bool "Support ARM926T processor"
+-	depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_NS9XXX
+-	default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_NS9XXX
++	depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_NS9XXX
++	default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_NS9XXX
+ 	select CPU_32v5
+ 	select CPU_ABRT_EV5TJ
+ 	select CPU_CACHE_VIVT
+diff -urN -x CVS linux-2.6.21/arch/arm/tools/mach-types linux-2.6-stable/arch/arm/tools/mach-types
+--- linux-2.6.21/arch/arm/tools/mach-types	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/arch/arm/tools/mach-types	Tue May  8 12:13:31 2007
+@@ -1335,3 +1335,32 @@
+ comtech_router		MACH_COMTECH_ROUTER	COMTECH_ROUTER		1327
+ sbc2410x		MACH_SBC2410X		SBC2410X		1328
+ at4x0bd			MACH_AT4X0BD		AT4X0BD			1329
++cbifr			MACH_CBIFR		CBIFR			1330
++arcom_quantum		MACH_ARCOM_QUANTUM	ARCOM_QUANTUM		1331
++matrix520		MACH_MATRIX520		MATRIX520		1332
++matrix510		MACH_MATRIX510		MATRIX510		1333
++matrix500		MACH_MATRIX500		MATRIX500		1334
++m501			MACH_M501		M501			1335
++aaeon1270		MACH_AAEON1270		AAEON1270		1336
++matrix500ev		MACH_MATRIX500EV	MATRIX500EV		1337
++pac500			MACH_PAC500		PAC500			1338
++pnx8181			MACH_PNX8181		PNX8181			1339
++colibri320		MACH_COLIBRI320		COLIBRI320		1340
++aztoolbb		MACH_AZTOOLBB		AZTOOLBB		1341
++aztoolg2		MACH_AZTOOLG2		AZTOOLG2		1342
++dvlhost			MACH_DVLHOST		DVLHOST			1343
++zir9200			MACH_ZIR9200		ZIR9200			1344
++zir9260			MACH_ZIR9260		ZIR9260			1345
++cocopah			MACH_COCOPAH		COCOPAH			1346
++nds			MACH_NDS		NDS			1347
++rosencrantz		MACH_ROSENCRANTZ	ROSENCRANTZ		1348
++fttx_odsc		MACH_FTTX_ODSC		FTTX_ODSC		1349
++classe_r6904		MACH_CLASSE_R6904	CLASSE_R6904		1350
++cam60			MACH_CAM60		CAM60			1351
++mxc30031ads		MACH_MXC30031ADS	MXC30031ADS		1352
++datacall		MACH_DATACALL		DATACALL		1353
++at91eb01		MACH_AT91EB01		AT91EB01		1354
++rty			MACH_RTY		RTY			1355
++dwl2100			MACH_DWL2100		DWL2100			1356
++vinsi			MACH_VINSI		VINSI			1357
++db88f5281		MACH_DB88F5281		DB88F5281		1358
+diff -urN -x CVS linux-2.6.21/drivers/char/Kconfig linux-2.6-stable/drivers/char/Kconfig
+--- linux-2.6.21/drivers/char/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/char/Kconfig	Tue May  8 14:31:24 2007
+@@ -1071,5 +1071,21 @@
+ 	  /sys/devices/platform/telco_clock, with a number of files for
+ 	  controlling the behavior of this hardware.
+ 
++config AT91_SPI
++	bool "SPI driver (legacy) for AT91RM9200 processors"
++	depends on ARCH_AT91RM9200
++	default y
++	help
++	  The SPI driver gives access to this serial bus on the AT91RM9200
++	  processor.
++
++config AT91_SPIDEV
++	bool "SPI device interface (legacy) for AT91RM9200 processors"
++	depends on ARCH_AT91RM9200 && AT91_SPI
++	default n
++	help
++	  The SPI driver gives user mode access to this serial
++	  bus on the AT91RM9200 processor.
++
+ endmenu
+ 
+diff -urN -x CVS linux-2.6.21/drivers/char/Makefile linux-2.6-stable/drivers/char/Makefile
+--- linux-2.6.21/drivers/char/Makefile	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/char/Makefile	Tue May  8 14:31:24 2007
+@@ -93,6 +93,8 @@
+ obj-$(CONFIG_GPIO_VR41XX)	+= vr41xx_giu.o
+ obj-$(CONFIG_TANBAC_TB0219)	+= tb0219.o
+ obj-$(CONFIG_TELCLOCK)		+= tlclk.o
++obj-$(CONFIG_AT91_SPI)		+= at91_spi.o
++obj-$(CONFIG_AT91_SPIDEV)	+= at91_spidev.o
+ 
+ obj-$(CONFIG_WATCHDOG)		+= watchdog/
+ obj-$(CONFIG_MWAVE)		+= mwave/
+diff -urN -x CVS linux-2.6.21/drivers/char/at91_spi.c linux-2.6-stable/drivers/char/at91_spi.c
+--- linux-2.6.21/drivers/char/at91_spi.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/char/at91_spi.c	Tue May  8 14:31:24 2007
+@@ -0,0 +1,336 @@
++/*
++ * Serial Peripheral Interface (SPI) driver for the Atmel AT91RM9200 (Thunder)
++ *
++ *  Copyright (C) SAN People (Pty) Ltd
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version
++ * 2 of the License, or (at your option) any later version.
++ */
++
++#include <linux/init.h>
++#include <linux/dma-mapping.h>
++#include <linux/module.h>
++#include <linux/sched.h>
++#include <linux/completion.h>
++#include <linux/interrupt.h>
++#include <linux/clk.h>
++#include <linux/platform_device.h>
++#include <linux/atmel_pdc.h>
++#include <asm/io.h>
++#include <asm/semaphore.h>
++
++#include <asm/arch/at91_spi.h>
++#include <asm/arch/board.h>
++#include <asm/arch/spi.h>
++
++#undef DEBUG_SPI
++
++static struct spi_local spi_dev[NR_SPI_DEVICES];	/* state of the SPI devices */
++static int spi_enabled = 0;
++static struct semaphore spi_lock;			/* protect access to SPI bus */
++static int current_device = -1;				/* currently selected SPI device */
++static struct clk *spi_clk;				/* SPI clock */
++static void __iomem *spi_base;				/* SPI peripheral base-address */
++
++DECLARE_COMPLETION(transfer_complete);
++
++
++#define at91_spi_read(reg)		__raw_readl(spi_base + (reg))
++#define at91_spi_write(reg, val)	__raw_writel((val), spi_base + (reg))
++
++
++/* ......................................................................... */
++
++/*
++ * Access and enable the SPI bus.
++ * This MUST be called before any transfers are performed.
++ */
++void spi_access_bus(short device)
++{
++	/* Ensure that requested device is valid */
++	if ((device < 0) || (device >= NR_SPI_DEVICES))
++		panic("at91_spi: spi_access_bus called with invalid device");
++
++	if (spi_enabled == 0) {
++		clk_enable(spi_clk);				/* Enable Peripheral clock */
++		at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIEN);	/* Enable SPI */
++#ifdef DEBUG_SPI
++		printk("SPI on\n");
++#endif
++	}
++	spi_enabled++;
++
++	/* Lock the SPI bus */
++	down(&spi_lock);
++	current_device = device;
++
++	/* Configure SPI bus for device */
++	at91_spi_write(AT91_SPI_MR, AT91_SPI_MSTR | AT91_SPI_MODFDIS | (spi_dev[device].pcs << 16));
++}
++
++/*
++ * Relinquish control of the SPI bus.
++ */
++void spi_release_bus(short device)
++{
++	if (device != current_device)
++		panic("at91_spi: spi_release called with invalid device");
++
++	/* Release the SPI bus */
++	current_device = -1;
++	up(&spi_lock);
++
++	spi_enabled--;
++	if (spi_enabled == 0) {
++		at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIDIS);	/* Disable SPI */
++		clk_disable(spi_clk);				/* Disable Peripheral clock */
++#ifdef DEBUG_SPI
++		printk("SPI off\n");
++#endif
++	}
++}
++
++/*
++ * Perform a data transfer over the SPI bus
++ */
++int spi_transfer(struct spi_transfer_list* list)
++{
++	struct spi_local *device = (struct spi_local *) &spi_dev[current_device];
++	int tx_size;
++
++	if (!list)
++		panic("at91_spi: spi_transfer called with NULL transfer list");
++	if (current_device == -1)
++		panic("at91_spi: spi_transfer called without acquiring bus");
++
++#ifdef DEBUG_SPI
++	printk("SPI transfer start [%i]\n", list->nr_transfers);
++#endif
++
++	/* If we are in 16-bit mode, we need to modify what we pass to the PDC */
++	tx_size = (at91_spi_read(AT91_SPI_CSR(current_device)) & AT91_SPI_BITS_16) ? 2 : 1;
++
++	/* Store transfer list */
++	device->xfers = list;
++	list->curr = 0;
++
++	/* Assume there must be at least one transfer */
++	device->tx = dma_map_single(NULL, list->tx[0], list->txlen[0], DMA_TO_DEVICE);
++	device->rx = dma_map_single(NULL, list->rx[0], list->rxlen[0], DMA_FROM_DEVICE);
++
++	/* Program PDC registers */
++	at91_spi_write(ATMEL_PDC_TPR, device->tx);
++	at91_spi_write(ATMEL_PDC_RPR, device->rx);
++	at91_spi_write(ATMEL_PDC_TCR, list->txlen[0] / tx_size);
++	at91_spi_write(ATMEL_PDC_RCR, list->rxlen[0] / tx_size);
++
++	/* Is there a second transfer? */
++	if (list->nr_transfers > 1) {
++		device->txnext = dma_map_single(NULL, list->tx[1], list->txlen[1], DMA_TO_DEVICE);
++		device->rxnext = dma_map_single(NULL, list->rx[1], list->rxlen[1], DMA_FROM_DEVICE);
++
++		/* Program Next PDC registers */
++		at91_spi_write(ATMEL_PDC_TNPR, device->txnext);
++		at91_spi_write(ATMEL_PDC_RNPR, device->rxnext);
++		at91_spi_write(ATMEL_PDC_TNCR, list->txlen[1] / tx_size);
++		at91_spi_write(ATMEL_PDC_RNCR, list->rxlen[1] / tx_size);
++	}
++	else {
++		device->txnext = 0;
++		device->rxnext = 0;
++		at91_spi_write(ATMEL_PDC_TNCR, 0);
++		at91_spi_write(ATMEL_PDC_RNCR, 0);
++	}
++
++	// TODO: If we are doing consecutive transfers (at high speed, or
++	//   small buffers), then it might be worth modifying the 'Delay between
++	//   Consecutive Transfers' in the CSR registers.
++	//   This is an issue if we cannot chain the next buffer fast enough
++	//   in the interrupt handler.
++
++	/* Enable transmitter and receiver */
++	at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN | ATMEL_PDC_TXTEN);
++
++	at91_spi_write(AT91_SPI_IER, AT91_SPI_ENDRX);		/* enable buffer complete interrupt */
++	wait_for_completion(&transfer_complete);
++
++#ifdef DEBUG_SPI
++	printk("SPI transfer end\n");
++#endif
++
++	return 0;
++}
++
++/* ......................................................................... */
++
++/*
++ * Handle interrupts from the SPI controller.
++ */
++static irqreturn_t at91spi_interrupt(int irq, void *dev_id)
++{
++	unsigned int status;
++	struct spi_local *device = (struct spi_local *) &spi_dev[current_device];
++	struct spi_transfer_list *list = device->xfers;
++
++#ifdef DEBUG_SPI
++	printk("SPI interrupt %i\n", current_device);
++#endif
++
++	if (!list)
++		panic("at91_spi: spi_interrupt with a NULL transfer list");
++
++		status = at91_spi_read(AT91_SPI_SR) & at91_spi_read(AT91_SPI_IMR);	/* read status */
++
++	dma_unmap_single(NULL, device->tx, list->txlen[list->curr], DMA_TO_DEVICE);
++	dma_unmap_single(NULL, device->rx, list->rxlen[list->curr], DMA_FROM_DEVICE);
++
++	device->tx = device->txnext;	/* move next transfer to current transfer */
++	device->rx = device->rxnext;
++
++	list->curr = list->curr + 1;
++	if (list->curr == list->nr_transfers) {		/* all transfers complete */
++		at91_spi_write(AT91_SPI_IDR, AT91_SPI_ENDRX);		/* disable interrupt */
++
++		/* Disable transmitter and receiver */
++		at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
++
++		device->xfers = NULL;
++		complete(&transfer_complete);
++	}
++	else if (list->curr+1 == list->nr_transfers) {	/* no more next transfers */
++		device->txnext = 0;
++		device->rxnext = 0;
++		at91_spi_write(ATMEL_PDC_TNCR, 0);
++		at91_spi_write(ATMEL_PDC_RNCR, 0);
++	}
++	else {
++		int i = (list->curr)+1;
++
++		/* If we are in 16-bit mode, we need to modify what we pass to the PDC */
++		int tx_size = (at91_spi_read(AT91_SPI_CSR(current_device)) & AT91_SPI_BITS_16) ? 2 : 1;
++
++		device->txnext = dma_map_single(NULL, list->tx[i], list->txlen[i], DMA_TO_DEVICE);
++		device->rxnext = dma_map_single(NULL, list->rx[i], list->rxlen[i], DMA_FROM_DEVICE);
++		at91_spi_write(ATMEL_PDC_TNPR, device->txnext);
++		at91_spi_write(ATMEL_PDC_RNPR, device->rxnext);
++		at91_spi_write(ATMEL_PDC_TNCR, list->txlen[i] / tx_size);
++		at91_spi_write(ATMEL_PDC_RNCR, list->rxlen[i] / tx_size);
++	}
++	return IRQ_HANDLED;
++}
++
++/* ......................................................................... */
++
++/*
++ * Initialize the SPI controller
++ */
++static int __init at91spi_probe(struct platform_device *pdev)
++{
++	int i;
++	unsigned long scbr;
++	struct resource *res;
++
++	init_MUTEX(&spi_lock);
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	if (!res)
++		return -ENXIO;
++
++	if (!request_mem_region(res->start, res->end - res->start + 1, "at91_spi"))
++		return -EBUSY;
++
++	spi_base = ioremap(res->start, res->end - res->start + 1);
++	if (!spi_base) {
++		release_mem_region(res->start, res->end - res->start + 1);
++		return -ENOMEM;
++	}
++
++	spi_clk = clk_get(NULL, "spi_clk");
++	if (IS_ERR(spi_clk)) {
++		printk(KERN_ERR "at91_spi: no clock defined\n");
++		iounmap(spi_base);
++		release_mem_region(res->start, res->end - res->start + 1);
++		return -ENODEV;
++	}
++
++	at91_spi_write(AT91_SPI_CR, AT91_SPI_SWRST);	/* software reset of SPI controller */
++
++	/*
++	 * Calculate the correct SPI baud-rate divisor.
++	 */
++	scbr = clk_get_rate(spi_clk) / (2 * DEFAULT_SPI_CLK);
++	scbr = scbr + 1;		/* round up */
++
++	printk(KERN_INFO "at91_spi: Baud rate set to %ld\n", clk_get_rate(spi_clk) / (2 * scbr));
++
++	/* Set Chip Select registers to good defaults */
++	for (i = 0; i < 4; i++) {
++		at91_spi_write(AT91_SPI_CSR(i), AT91_SPI_CPOL | AT91_SPI_BITS_8 | (16 << 16) | (scbr << 8));
++	}
++
++	at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
++
++	memset(&spi_dev, 0, sizeof(spi_dev));
++	spi_dev[0].pcs = 0xE;
++	spi_dev[1].pcs = 0xD;
++	spi_dev[2].pcs = 0xB;
++	spi_dev[3].pcs = 0x7;
++
++	if (request_irq(AT91RM9200_ID_SPI, at91spi_interrupt, 0, "spi", NULL)) {
++		clk_put(spi_clk);
++		iounmap(spi_base);
++		release_mem_region(res->start, res->end - res->start + 1);
++		return -EBUSY;
++	}
++
++	at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIEN);		/* Enable SPI */
++
++	return 0;
++}
++
++static int __devexit at91spi_remove(struct platform_device *pdev)
++{
++	struct resource *res;
++
++	at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIDIS);		/* Disable SPI */
++	clk_put(spi_clk);
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	iounmap(spi_base);
++	release_mem_region(res->start, res->end - res->start + 1);
++
++	free_irq(AT91RM9200_ID_SPI, 0);
++	return 0;
++}
++
++static struct platform_driver at91spi_driver = {
++	.probe		= at91spi_probe,
++	.remove		= __devexit_p(at91spi_remove),
++	.driver		= {
++		.name	= "at91_spi",
++		.owner	= THIS_MODULE,
++	},
++};
++
++static int __init at91spi_init(void)
++{
++	return platform_driver_register(&at91spi_driver);
++}
++
++static void __exit at91spi_exit(void)
++{
++	platform_driver_unregister(&at91spi_driver);
++}
++
++EXPORT_SYMBOL(spi_access_bus);
++EXPORT_SYMBOL(spi_release_bus);
++EXPORT_SYMBOL(spi_transfer);
++
++module_init(at91spi_init);
++module_exit(at91spi_exit);
++
++MODULE_LICENSE("GPL")
++MODULE_AUTHOR("Andrew Victor")
++MODULE_DESCRIPTION("SPI driver for Atmel AT91RM9200")
+diff -urN -x CVS linux-2.6.21/drivers/char/at91_spidev.c linux-2.6-stable/drivers/char/at91_spidev.c
+--- linux-2.6.21/drivers/char/at91_spidev.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/char/at91_spidev.c	Tue May  8 14:31:24 2007
+@@ -0,0 +1,236 @@
++/*
++ * User-space interface to the SPI bus on Atmel AT91RM9200
++ *
++ *  Copyright (C) 2003 SAN People (Pty) Ltd
++ *
++ * Based on SPI driver by Rick Bronson
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version
++ * 2 of the License, or (at your option) any later version.
++ */
++
++#include <linux/module.h>
++#include <linux/init.h>
++#include <linux/slab.h>
++#include <linux/highmem.h>
++#include <linux/pagemap.h>
++#include <asm/arch/spi.h>
++
++#ifdef CONFIG_DEVFS_FS
++#include <linux/devfs_fs_kernel.h>
++#endif
++
++
++#undef DEBUG_SPIDEV
++
++/* ......................................................................... */
++
++/*
++ * Read or Write to SPI bus.
++ */
++static ssize_t spidev_rd_wr(struct file *file, char *buf, size_t count, loff_t *offset)
++{
++	unsigned int spi_device = (unsigned int) file->private_data;
++
++	struct mm_struct * mm;
++	struct page ** maplist;
++	struct spi_transfer_list* list;
++	int    pgcount;
++
++	unsigned int ofs, pagelen;
++	int res, i, err;
++
++	if (!count) {
++		return 0;
++	}
++
++	list = kmalloc(sizeof(struct spi_transfer_list), GFP_KERNEL);
++	if (!list) {
++		return -ENOMEM;
++	}
++
++	mm = current->mm;
++
++	pgcount = ((unsigned long)buf+count+PAGE_SIZE-1)/PAGE_SIZE - (unsigned long)buf/PAGE_SIZE;
++
++	if (pgcount >= MAX_SPI_TRANSFERS) {
++		kfree(list);
++		return -EFBIG;
++	}
++
++	maplist = kmalloc (pgcount * sizeof (struct page *), GFP_KERNEL);
++
++	if (!maplist) {
++		kfree(list);
++		return -ENOMEM;
++	}
++	flush_cache_all();
++	down_read(&mm->mmap_sem);
++	err= get_user_pages(current, mm, (unsigned long)buf, pgcount, 1, 0, maplist, NULL);
++	up_read(&mm->mmap_sem);
++
++	if (err < 0) {
++		kfree(list);
++		kfree(maplist);
++		return err;
++	}
++	pgcount = err;
++
++#ifdef DEBUG_SPIDEV
++	printk("spidev_rd_rw: %i %i\n", count, pgcount);
++#endif
++
++	/* Set default return value = transfer length */
++	res = count;
++
++	/*
++	 * At this point, the virtual area buf[0] .. buf[count-1] will have
++	 * corresponding pages mapped in the physical memory and locked until
++	 * we unmap the kiobuf.  The pages cannot be swapped out or moved
++	 * around.
++	 */
++	ofs = (unsigned long) buf & (PAGE_SIZE -1);
++	pagelen = PAGE_SIZE - ofs;
++	if (count < pagelen)
++		pagelen = count;
++
++	for (i = 0; i < pgcount; i++) {
++		flush_dcache_page(maplist[i]);
++
++		list->tx[i] = list->rx[i] = page_address(maplist[i]) + ofs;
++		list->txlen[i] = list->rxlen[i] = pagelen;
++
++#ifdef DEBUG_SPIDEV
++		printk("  %i: %x  (%i)\n", i, list->tx[i], list->txlen[i]);
++#endif
++
++		ofs = 0;	/* all subsequent transfers start at beginning of a page */
++		count = count - pagelen;
++		pagelen = (count < PAGE_SIZE) ? count : PAGE_SIZE;
++	}
++	list->nr_transfers = pgcount;
++
++	/* Perform transfer on SPI bus */
++	spi_access_bus(spi_device);
++	spi_transfer(list);
++	spi_release_bus(spi_device);
++
++	while (pgcount--) {
++		page_cache_release (maplist[pgcount]);
++	}
++	flush_cache_all();
++
++	kfree(maplist);
++	kfree(list);
++
++	return res;
++}
++
++static int spidev_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
++{
++	int spi_device = MINOR(inode->i_rdev);
++
++	if (spi_device >= NR_SPI_DEVICES)
++		return -ENODEV;
++
++	// TODO: This interface can be used to configure the SPI bus.
++	// Configurable options could include: Speed, Clock Polarity, Clock Phase
++
++	switch(cmd) {
++		default:
++			return -ENOIOCTLCMD;
++	}
++}
++
++/*
++ * Open the SPI device
++ */
++static int spidev_open(struct inode *inode, struct file *file)
++{
++	unsigned int spi_device = MINOR(inode->i_rdev);
++
++	if (spi_device >= NR_SPI_DEVICES)
++		return -ENODEV;
++
++	/*
++	 * 'private_data' is actually a pointer, but we overload it with the
++	 * value we want to store.
++	 */
++	file->private_data = (void *)spi_device;
++
++	return 0;
++}
++
++/*
++ * Close the SPI device
++ */
++static int spidev_close(struct inode *inode, struct file *file)
++{
++	return 0;
++}
++
++/* ......................................................................... */
++
++static struct file_operations spidev_fops = {
++	.owner		= THIS_MODULE,
++	.llseek		= no_llseek,
++	.read		= spidev_rd_wr,
++	.write		= (int (*) (struct file *file, const char *buf, size_t count, loff_t *offset))spidev_rd_wr,
++	.ioctl		= spidev_ioctl,
++	.open		= spidev_open,
++	.release	= spidev_close,
++};
++
++/*
++ * Install the SPI /dev interface driver
++ */
++static int __init at91_spidev_init(void)
++{
++#ifdef CONFIG_DEVFS_FS
++	int i;
++#endif
++
++	if (register_chrdev(SPI_MAJOR, "spi", &spidev_fops)) {
++		printk(KERN_ERR "at91_spidev: Unable to get major %d for SPI bus\n", SPI_MAJOR);
++		return -EIO;
++	}
++
++#ifdef CONFIG_DEVFS_FS
++	devfs_mk_dir("spi");
++	for (i = 0; i < NR_SPI_DEVICES; i++) {
++		devfs_mk_cdev(MKDEV(SPI_MAJOR, i), S_IFCHR | S_IRUSR | S_IWUSR, "spi/%d",i);
++	}
++#endif
++	printk(KERN_INFO "AT91 SPI driver loaded\n");
++
++	return 0;
++}
++
++/*
++ * Remove the SPI /dev interface driver
++ */
++static void __exit at91_spidev_exit(void)
++{
++#ifdef CONFIG_DEVFS_FS
++	int i;
++	for (i = 0; i < NR_SPI_DEVICES; i++) {
++		devfs_remove("spi/%d", i);
++	}
++
++	devfs_remove("spi");
++#endif
++
++	if (unregister_chrdev(SPI_MAJOR, "spi")) {
++		printk(KERN_ERR "at91_spidev: Unable to release major %d for SPI bus\n", SPI_MAJOR);
++		return;
++	}
++}
++
++module_init(at91_spidev_init);
++module_exit(at91_spidev_exit);
++
++MODULE_LICENSE("GPL")
++MODULE_AUTHOR("Andrew Victor")
++MODULE_DESCRIPTION("SPI /dev interface for Atmel AT91RM9200")
+diff -urN -x CVS linux-2.6.21/drivers/i2c/busses/Kconfig linux-2.6-stable/drivers/i2c/busses/Kconfig
+--- linux-2.6.21/drivers/i2c/busses/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/i2c/busses/Kconfig	Tue May  8 12:13:31 2007
+@@ -81,6 +81,14 @@
+ 	  This supports the use of the I2C interface on Atmel AT91
+ 	  processors.
+ 
++config I2C_AT91_CLOCKRATE
++	prompt "Atmel AT91 I2C/TWI clock-rate"
++	depends on I2C_AT91
++	int
++	default 100000
++	help
++	  Set the AT91 I2C/TWI clock-rate.
++
+ config I2C_AU1550
+ 	tristate "Au1550/Au1200 SMBus interface"
+ 	depends on I2C && (SOC_AU1550 || SOC_AU1200)
+@@ -545,6 +553,14 @@
+ 	  This driver can also be built as a module.  If so, the module
+ 	  will be called i2c-voodoo3.
+ 
++config I2C_PCA
++	tristate "PCA9564"
++	depends on I2C
++	select I2C_ALGOPCA
++	help
++	  This driver support the Philips PCA 9564 Parallel bus to I2C
++	  bus controller.
++
+ config I2C_PCA_ISA
+ 	tristate "PCA9564 on an ISA bus"
+ 	depends on I2C
+diff -urN -x CVS linux-2.6.21/drivers/i2c/busses/Makefile linux-2.6-stable/drivers/i2c/busses/Makefile
+--- linux-2.6.21/drivers/i2c/busses/Makefile	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/i2c/busses/Makefile	Tue May  8 12:13:31 2007
+@@ -28,6 +28,7 @@
+ obj-$(CONFIG_I2C_PARPORT)	+= i2c-parport.o
+ obj-$(CONFIG_I2C_PARPORT_LIGHT)	+= i2c-parport-light.o
+ obj-$(CONFIG_I2C_PASEMI)	+= i2c-pasemi.o
++obj-$(CONFIG_I2C_PCA)		+= i2c-pca.o
+ obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
+ obj-$(CONFIG_I2C_PIIX4)		+= i2c-piix4.o
+ obj-$(CONFIG_I2C_PNX)		+= i2c-pnx.o
+diff -urN -x CVS linux-2.6.21/drivers/i2c/busses/i2c-at91.c linux-2.6-stable/drivers/i2c/busses/i2c-at91.c
+--- linux-2.6.21/drivers/i2c/busses/i2c-at91.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/i2c/busses/i2c-at91.c	Tue May  8 12:13:31 2007
+@@ -31,8 +31,11 @@
+ #include <asm/arch/board.h>
+ #include <asm/arch/cpu.h>
+ 
+-#define TWI_CLOCK		100000		/* Hz. max 400 Kbits/sec */
+ 
++/* Clockrate is configurable - max 400 Kbits/sec */
++static unsigned int clockrate = CONFIG_I2C_AT91_CLOCKRATE;
++module_param(clockrate, uint, 0);
++MODULE_PARM_DESC(clockrate, "The TWI clockrate");
+ 
+ static struct clk *twi_clk;
+ static void __iomem *twi_base;
+@@ -53,7 +56,7 @@
+ 	at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN);	/* Set Master mode */
+ 
+ 	/* Calcuate clock dividers */
+-	cdiv = (clk_get_rate(twi_clk) / (2 * TWI_CLOCK)) - 3;
++	cdiv = (clk_get_rate(twi_clk) / (2 * clockrate)) - 3;
+ 	cdiv = cdiv + 1;	/* round up */
+ 	ckdiv = 0;
+ 	while (cdiv > 255) {
+@@ -61,11 +64,12 @@
+ 		cdiv = cdiv >> 1;
+ 	}
+ 
+-	if (cpu_is_at91rm9200()) {			/* AT91RM9200 Errata #22 */
+-		if (ckdiv > 5) {
+-			printk(KERN_ERR "AT91 I2C: Invalid TWI_CLOCK value!\n");
+-			ckdiv = 5;
+-		}
++	if (cpu_is_at91rm9200() && (ckdiv > 5)) {	/* AT91RM9200 Errata #22 */
++		printk(KERN_ERR "AT91 I2C: Invalid TWI clockrate!\n");
++		ckdiv = 5;
++	} else if (ckdiv > 7) {
++		printk(KERN_ERR "AT91 I2C: Invalid TWI clockrate!\n");
++		ckdiv = 7;
+ 	}
+ 
+ 	at91_twi_write(AT91_TWI_CWGR, (ckdiv << 16) | (cdiv << 8) | cdiv);
+diff -urN -x CVS linux-2.6.21/drivers/i2c/busses/i2c-pca.c linux-2.6-stable/drivers/i2c/busses/i2c-pca.c
+--- linux-2.6.21/drivers/i2c/busses/i2c-pca.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/i2c/busses/i2c-pca.c	Tue May  8 12:13:31 2007
+@@ -0,0 +1,213 @@
++/*
++ *  Platform driver for PCA9564 I2C bus controller.
++ *
++ *  (C) 2006 Andrew Victor
++ *
++ *  Based on i2c-pca-isa.c driver for PCA9564 on ISA boards
++ *    Copyright (C) 2004 Arcom Control Systems
++ *
++ *  This program is free software; you can redistribute it and/or modify
++ *  it under the terms of the GNU General Public License as published by
++ *  the Free Software Foundation; either version 2 of the License, or
++ *  (at your option) any later version.
++ *
++ *  This program is distributed in the hope that it will be useful,
++ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
++ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ *  GNU General Public License for more details.
++ *
++ *  You should have received a copy of the GNU General Public License
++ *  along with this program; if not, write to the Free Software
++ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
++ */
++
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/moduleparam.h>
++#include <linux/delay.h>
++#include <linux/init.h>
++#include <linux/interrupt.h>
++#include <linux/wait.h>
++#include <linux/platform_device.h>
++
++#include <linux/i2c.h>
++#include <linux/i2c-algo-pca.h>
++
++#include <asm/io.h>
++
++#include "../algos/i2c-algo-pca.h"
++
++#define PCA_OWN_ADDRESS		0x55	/* our address for slave mode */
++#define PCA_CLOCK		I2C_PCA_CON_59kHz
++
++//#define REG_SHIFT		2
++#define REG_SHIFT		0
++
++//#define DEBUG_IO
++
++#define PCA_IO_SIZE 4
++
++static void __iomem *base_addr;
++static int irq;
++static wait_queue_head_t pca_wait;
++
++static int pca_getown(struct i2c_algo_pca_data *adap)
++{
++	return PCA_OWN_ADDRESS;
++}
++
++static int pca_getclock(struct i2c_algo_pca_data *adap)
++{
++	return PCA_CLOCK;
++}
++
++static void pca_writebyte(struct i2c_algo_pca_data *adap, int reg, int val)
++{
++#ifdef DEBUG_IO
++	static char *names[] = { "T/O", "DAT", "ADR", "CON" };
++	printk("*** write %s at %#lx <= %#04x\n", names[reg], (unsigned long) base_addr+reg, val);
++#endif
++	udelay(1);
++	outb(val, base_addr + (reg << REG_SHIFT));
++}
++
++static int pca_readbyte(struct i2c_algo_pca_data *adap, int reg)
++{
++	int res;
++
++	udelay(1);
++	res = inb(base_addr + (reg << REG_SHIFT));
++#ifdef DEBUG_IO
++	{
++		static char *names[] = { "STA", "DAT", "ADR", "CON" };
++		printk("*** read  %s => %#04x\n", names[reg], res);
++	}
++#endif
++	return res;
++}
++
++static int pca_waitforinterrupt(struct i2c_algo_pca_data *adap)
++{
++	int ret = 0;
++
++	if (irq > -1) {
++		ret = wait_event_interruptible(pca_wait,
++				pca_readbyte(adap, I2C_PCA_CON) & I2C_PCA_CON_SI);
++	} else {
++		while ((pca_readbyte(adap, I2C_PCA_CON) & I2C_PCA_CON_SI) == 0)
++			udelay(100);
++	}
++	return ret;
++}
++
++static irqreturn_t pca_handler(int this_irq, void *dev_id)
++{
++	wake_up_interruptible(&pca_wait);
++	return IRQ_HANDLED;
++}
++
++static struct i2c_algo_pca_data pca_i2c_data = {
++	.get_own		= pca_getown,
++	.get_clock		= pca_getclock,
++	.write_byte		= pca_writebyte,
++	.read_byte		= pca_readbyte,
++	.wait_for_interrupt	= pca_waitforinterrupt,
++};
++
++static struct i2c_adapter pca_i2c_ops = {
++	.owner          = THIS_MODULE,
++	.id		= I2C_HW_A_PLAT,
++	.algo_data	= &pca_i2c_data,
++	.name		= "PCA9564",
++	.class		= I2C_CLASS_HWMON,
++};
++
++static int __devinit pca_i2c_probe(struct platform_device *pdev)
++{
++	struct resource *res;
++
++	init_waitqueue_head(&pca_wait);
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	if (!res)
++		return -ENODEV;
++
++	if (!request_mem_region(res->start, PCA_IO_SIZE, "PCA9564"))
++		return -ENXIO;
++
++	base_addr = ioremap(res->start, PCA_IO_SIZE);
++	if (base_addr == NULL)
++		goto out_region;
++
++	irq = platform_get_irq(pdev, 0);
++	if (irq > -1) {
++		if (request_irq(irq, pca_handler, 0, "pca9564", NULL) < 0) {
++			printk(KERN_ERR "i2c-pca: Request irq%d failed\n", irq);
++			goto out_remap;
++		}
++	}
++
++	/* set up the driverfs linkage to our parent device */
++	pca_i2c_ops.dev.parent = &pdev->dev;
++
++	if (i2c_pca_add_bus(&pca_i2c_ops) < 0) {
++		printk(KERN_ERR "i2c-pca: Failed to add i2c bus\n");
++		goto out_irq;
++	}
++
++	return 0;
++
++ out_irq:
++	if (irq > -1)
++		free_irq(irq, &pca_i2c_ops);
++
++ out_remap:
++	iounmap(base_addr);
++
++ out_region:
++	release_mem_region(res->start, PCA_IO_SIZE);
++	return -ENODEV;
++}
++
++static int __devexit pca_i2c_remove(struct platform_device *pdev)
++{
++	struct resource *res;
++
++	i2c_del_adapter(&pca_i2c_ops);
++
++	if (irq > 0)
++		free_irq(irq, NULL);
++
++	iounmap(base_addr);
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	release_mem_region(res->start, PCA_IO_SIZE);
++
++	return 0;
++}
++
++static struct platform_driver pca_i2c_driver = {
++	.probe		= pca_i2c_probe,
++	.remove		= __devexit_p(pca_i2c_remove),
++	.driver		= {
++		.name	= "pca9564",
++		.owner	= THIS_MODULE,
++	},
++};
++
++static int __init pca_i2c_init(void)
++{
++	return platform_driver_register(&pca_i2c_driver);
++}
++
++static void __exit pca_i2c_exit(void)
++{
++	platform_driver_unregister(&pca_i2c_driver);
++}
++
++module_init(pca_i2c_init);
++module_exit(pca_i2c_exit);
++
++MODULE_AUTHOR("Andrew Victor");
++MODULE_DESCRIPTION("PCA9564 platform driver");
++MODULE_LICENSE("GPL");
+diff -urN -x CVS linux-2.6.21/drivers/input/touchscreen/ads7846.c linux-2.6-stable/drivers/input/touchscreen/ads7846.c
+--- linux-2.6.21/drivers/input/touchscreen/ads7846.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/input/touchscreen/ads7846.c	Tue May  8 12:56:33 2007
+@@ -39,7 +39,8 @@
+ /*
+  * This code has been heavily tested on a Nokia 770, and lightly
+  * tested on other ads7846 devices (OSK/Mistral, Lubbock).
+- * Support for ads7843 and ads7845 has only been stubbed in.
++ * Support for ads7843 tested on Atmel at91sam926x-EK.
++ * Support for ads7845 has only been stubbed in.
+  *
+  * IRQ handling needs a workaround because of a shortcoming in handling
+  * edge triggered IRQs on some platforms like the OMAP1/2. These
+@@ -246,18 +247,16 @@
+ 
+ 	/* REVISIT:  take a few more samples, and compare ... */
+ 
+-	/* maybe off internal vREF */
+-	if (use_internal) {
+-		req->ref_off = REF_OFF;
+-		req->xfer[4].tx_buf = &req->ref_off;
+-		req->xfer[4].len = 1;
+-		spi_message_add_tail(&req->xfer[4], &req->msg);
+-
+-		req->xfer[5].rx_buf = &req->scratch;
+-		req->xfer[5].len = 2;
+-		CS_CHANGE(req->xfer[5]);
+-		spi_message_add_tail(&req->xfer[5], &req->msg);
+-	}
++	/* converter in low power mode & enable PENIRQ */
++	req->ref_off = PWRDOWN;
++	req->xfer[4].tx_buf = &req->ref_off;
++	req->xfer[4].len = 1;
++	spi_message_add_tail(&req->xfer[4], &req->msg);
++
++	req->xfer[5].rx_buf = &req->scratch;
++	req->xfer[5].len = 2;
++	CS_CHANGE(req->xfer[5]);
++	spi_message_add_tail(&req->xfer[5], &req->msg);
+ 
+ 	ts->irq_disabled = 1;
+ 	disable_irq(spi->irq);
+@@ -536,6 +535,9 @@
+ 	} else
+ 		Rt = 0;
+ 
++	if (ts->model == 7843)
++		Rt = ts->pressure_max / 2;
++
+ 	/* Sample found inconsistent by debouncing or pressure is beyond
+ 	 * the maximum. Don't report it to user space, repeat at least
+ 	 * once more the measurement
+diff -urN -x CVS linux-2.6.21/drivers/leds/Kconfig linux-2.6-stable/drivers/leds/Kconfig
+--- linux-2.6.21/drivers/leds/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/leds/Kconfig	Tue May  8 12:13:31 2007
+@@ -76,6 +76,13 @@
+ 	  This option enables support for the Soekris net4801 and net4826 error
+ 	  LED.
+ 
++config LEDS_AT91
++	tristate "LED support using AT91 GPIOs"
++	depends on LEDS_CLASS && ARCH_AT91 && !LEDS
++	help
++	  This option enables support for LEDs connected to GPIO lines
++	  on AT91-based boards.
++
+ config LEDS_WRAP
+ 	tristate "LED Support for the WRAP series LEDs"
+ 	depends on LEDS_CLASS && SCx200_GPIO
+diff -urN -x CVS linux-2.6.21/drivers/leds/Makefile linux-2.6-stable/drivers/leds/Makefile
+--- linux-2.6.21/drivers/leds/Makefile	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/leds/Makefile	Tue May  8 12:13:31 2007
+@@ -16,6 +16,7 @@
+ obj-$(CONFIG_LEDS_WRAP)			+= leds-wrap.o
+ obj-$(CONFIG_LEDS_H1940)		+= leds-h1940.o
+ obj-$(CONFIG_LEDS_COBALT)		+= leds-cobalt.o
++obj-$(CONFIG_LEDS_AT91)			+= leds-at91.o
+ 
+ # LED Triggers
+ obj-$(CONFIG_LEDS_TRIGGER_TIMER)	+= ledtrig-timer.o
+diff -urN -x CVS linux-2.6.21/drivers/leds/leds-at91.c linux-2.6-stable/drivers/leds/leds-at91.c
+--- linux-2.6.21/drivers/leds/leds-at91.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/leds/leds-at91.c	Tue May  8 12:13:31 2007
+@@ -0,0 +1,140 @@
++/*
++ * AT91 GPIO based LED driver
++ *
++ * Copyright (C) 2006 David Brownell
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/leds.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++
++static LIST_HEAD(at91_led_list);	/* list of AT91 LEDs */
++
++struct at91_led {
++	struct led_classdev	cdev;
++	struct list_head	list;
++	struct at91_gpio_led	*led_data;
++};
++
++/*
++ * Change the state of the LED.
++ */
++static void at91_led_set(struct led_classdev *cdev, enum led_brightness value)
++{
++	struct at91_led	*led = container_of(cdev, struct at91_led, cdev);
++	short		active = (value == LED_OFF);
++
++	if (led->led_data->flags & 1)	/* active high/low? */
++		active = !active;
++	at91_set_gpio_value(led->led_data->gpio, active);
++}
++
++static int __devexit at91_led_remove(struct platform_device *pdev)
++{
++	struct at91_led		*led;
++
++	list_for_each_entry (led, &at91_led_list, list)
++		led_classdev_unregister(&led->cdev);
++
++#warning "Free allocated memory"
++	// TODO: Free memory.	kfree(led);
++
++	return 0;
++}
++
++static int __init at91_led_probe(struct platform_device *pdev)
++{
++	int			status = 0;
++	struct at91_gpio_led	*pdata = pdev->dev.platform_data;
++	unsigned		nr_leds;
++	struct at91_led		*led;
++
++	if (!pdata)
++		return -ENODEV;
++
++	nr_leds = pdata->index;		/* first index stores number of LEDs */
++
++	while (nr_leds--) {
++		led = kzalloc(sizeof(struct at91_led), GFP_KERNEL);
++		if (!led) {
++			dev_err(&pdev->dev, "No memory for device\n");
++			status = -ENOMEM;
++			goto cleanup;
++		}
++		led->led_data = pdata;
++		led->cdev.name = pdata->name;
++		led->cdev.brightness_set = at91_led_set,
++		led->cdev.default_trigger = pdata->trigger;
++
++		status = led_classdev_register(&pdev->dev, &led->cdev);
++		if (status < 0) {
++			dev_err(&pdev->dev, "led_classdev_register failed - %d\n", status);
++cleanup:
++			at91_led_remove(pdev);
++			break;
++		}
++		list_add(&led->list, &at91_led_list);
++		pdata++;
++	}
++	return status;
++}
++
++#ifdef CONFIG_PM
++static int at91_led_suspend(struct platform_device *dev, pm_message_t state)
++{
++	struct at91_led	*led;
++
++	list_for_each_entry (led, &at91_led_list, list)
++		led_classdev_suspend(&led->cdev);
++
++	return 0;
++}
++
++static int at91_led_resume(struct platform_device *dev)
++{
++	struct at91_led	*led;
++
++	list_for_each_entry (led, &at91_led_list, list)
++		led_classdev_resume(&led->cdev);
++
++	return 0;
++}
++#else
++#define	at91_led_suspend	NULL
++#define	at91_led_resume		NULL
++#endif
++
++static struct platform_driver at91_led_driver = {
++	.probe		= at91_led_probe,
++	.remove		= __devexit_p(at91_led_remove),
++	.suspend	= at91_led_suspend,
++	.resume		= at91_led_resume,
++	.driver		= {
++		.name	= "at91_leds",
++		.owner	= THIS_MODULE,
++	},
++};
++
++static int __init at91_led_init(void)
++{
++	return platform_driver_register(&at91_led_driver);
++}
++module_init(at91_led_init);
++
++static void __exit at91_led_exit(void)
++{
++	platform_driver_unregister(&at91_led_driver);
++}
++module_exit(at91_led_exit);
++
++MODULE_DESCRIPTION("AT91 GPIO LED driver");
++MODULE_AUTHOR("David Brownell");
++MODULE_LICENSE("GPL");
+diff -urN -x CVS linux-2.6.21/drivers/mmc/at91_mci.c linux-2.6-stable/drivers/mmc/at91_mci.c
+--- linux-2.6.21/drivers/mmc/at91_mci.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/mmc/at91_mci.c	Fri May 11 17:13:13 2007
+@@ -86,7 +86,7 @@
+ 
+ #define AT91_MCI_ERRORS	(AT91_MCI_RINDE | AT91_MCI_RDIRE | AT91_MCI_RCRCE	\
+ 		| AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE		\
+-		| AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)			
++		| AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)
+ 
+ #define at91_mci_read(host, reg)	__raw_readl((host)->baseaddr + (reg))
+ #define at91_mci_write(host, reg, val)	__raw_writel((val), (host)->baseaddr + (reg))
+@@ -561,9 +561,7 @@
+ 	pr_debug("Status = %08X [%08X %08X %08X %08X]\n",
+ 		 status, cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]);
+ 
+-	if (status & (AT91_MCI_RINDE | AT91_MCI_RDIRE | AT91_MCI_RCRCE |
+-			AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE |
+-			AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)) {
++	if (status & AT91_MCI_ERRORS) {
+ 		if ((status & AT91_MCI_RCRCE) &&
+ 			((cmd->opcode == MMC_SEND_OP_COND) || (cmd->opcode == SD_APP_OP_COND))) {
+ 			cmd->error = MMC_ERR_NONE;
+@@ -665,15 +663,15 @@
+ 
+ 	int_status = at91_mci_read(host, AT91_MCI_SR);
+ 	int_mask = at91_mci_read(host, AT91_MCI_IMR);
+-	
++
+ 	pr_debug("MCI irq: status = %08X, %08X, %08X\n", int_status, int_mask,
+ 		int_status & int_mask);
+-	
++
+ 	int_status = int_status & int_mask;
+ 
+ 	if (int_status & AT91_MCI_ERRORS) {
+ 		completed = 1;
+-		
++
+ 		if (int_status & AT91_MCI_UNRE)
+ 			pr_debug("MMC: Underrun error\n");
+ 		if (int_status & AT91_MCI_OVRE)
+@@ -821,7 +819,7 @@
+ 	mmc->f_min = 375000;
+ 	mmc->f_max = 25000000;
+ 	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+-	mmc->caps = MMC_CAP_BYTEBLOCK;
++	mmc->caps = MMC_CAP_BYTEBLOCK | MMC_CAP_MULTIWRITE;
+ 
+ 	mmc->max_blk_size = 4095;
+ 	mmc->max_blk_count = mmc->max_req_size;
+@@ -895,6 +893,8 @@
+ 
+ 	mmc_add_host(mmc);
+ 
++	device_init_wakeup(&pdev->dev, 1);
++
+ 	/*
+ 	 * monitor card insertion/removal if we can
+ 	 */
+@@ -924,6 +924,8 @@
+ 
+ 	host = mmc_priv(mmc);
+ 
++	device_init_wakeup(&pdev->dev, 0);
++
+ 	if (host->present != -1) {
+ 		free_irq(host->board->det_pin, host);
+ 		cancel_delayed_work(&host->mmc->detect);
+@@ -951,8 +953,12 @@
+ static int at91_mci_suspend(struct platform_device *pdev, pm_message_t state)
+ {
+ 	struct mmc_host *mmc = platform_get_drvdata(pdev);
++	struct at91mci_host *host = mmc_priv(mmc);
+ 	int ret = 0;
+ 
++	if (device_may_wakeup(&pdev->dev))
++		enable_irq_wake(host->board->det_pin);
++
+ 	if (mmc)
+ 		ret = mmc_suspend_host(mmc, state);
+ 
+@@ -962,8 +968,12 @@
+ static int at91_mci_resume(struct platform_device *pdev)
+ {
+ 	struct mmc_host *mmc = platform_get_drvdata(pdev);
++	struct at91mci_host *host = mmc_priv(mmc);
+ 	int ret = 0;
+ 
++	if (device_may_wakeup(&pdev->dev))
++		disable_irq_wake(host->board->det_pin);
++
+ 	if (mmc)
+ 		ret = mmc_resume_host(mmc);
+ 
+diff -urN -x CVS linux-2.6.21/drivers/mtd/devices/Kconfig linux-2.6-stable/drivers/mtd/devices/Kconfig
+--- linux-2.6.21/drivers/mtd/devices/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/mtd/devices/Kconfig	Tue May  8 14:31:24 2007
+@@ -267,5 +267,11 @@
+ 	  LinuxBIOS or if you need to recover a DiskOnChip Millennium on which
+ 	  you have managed to wipe the first block.
+ 
+-endmenu
++config MTD_AT91_DATAFLASH
++	tristate "AT91RM9200 DataFlash AT45DBxxx (legacy driver)"
++	depends on MTD && ARCH_AT91RM9200 && AT91_SPI
++	help
++	  This enables access to the DataFlash (AT45DBxxx) on the AT91RM9200.
++	  If you have such a board, say 'Y'.
+ 
++endmenu
+diff -urN -x CVS linux-2.6.21/drivers/mtd/devices/Makefile linux-2.6-stable/drivers/mtd/devices/Makefile
+--- linux-2.6.21/drivers/mtd/devices/Makefile	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/mtd/devices/Makefile	Tue May  8 14:31:24 2007
+@@ -17,3 +17,4 @@
+ obj-$(CONFIG_MTD_BLOCK2MTD)	+= block2mtd.o
+ obj-$(CONFIG_MTD_DATAFLASH)	+= mtd_dataflash.o
+ obj-$(CONFIG_MTD_M25P80)	+= m25p80.o
++obj-$(CONFIG_MTD_AT91_DATAFLASH)+= at91_dataflash.o
+diff -urN -x CVS linux-2.6.21/drivers/mtd/devices/at91_dataflash.c linux-2.6-stable/drivers/mtd/devices/at91_dataflash.c
+--- linux-2.6.21/drivers/mtd/devices/at91_dataflash.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/mtd/devices/at91_dataflash.c	Tue May  8 14:31:24 2007
+@@ -0,0 +1,667 @@
++/*
++ * Atmel DataFlash driver for Atmel AT91RM9200 (Thunder)
++ *
++ *  Copyright (C) SAN People (Pty) Ltd
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version
++ * 2 of the License, or (at your option) any later version.
++*/
++
++#include <linux/module.h>
++#include <linux/init.h>
++#include <linux/slab.h>
++#include <linux/pci.h>
++#include <linux/mtd/mtd.h>
++#include <linux/mtd/partitions.h>
++
++#include <asm/arch/spi.h>
++
++#undef DEBUG_DATAFLASH
++
++#define DATAFLASH_MAX_DEVICES	4	/* max number of dataflash devices */
++#undef	DATAFLASH_ALWAYS_ADD_DEVICE	/* always add whole device when using partitions? */
++
++#define OP_READ_CONTINUOUS	0xE8
++#define OP_READ_PAGE		0xD2
++#define OP_READ_BUFFER1		0xD4
++#define OP_READ_BUFFER2		0xD6
++#define OP_READ_STATUS		0xD7
++
++#define OP_ERASE_PAGE		0x81
++#define OP_ERASE_BLOCK		0x50
++
++#define OP_TRANSFER_BUF1	0x53
++#define OP_TRANSFER_BUF2	0x55
++#define OP_COMPARE_BUF1		0x60
++#define OP_COMPARE_BUF2		0x61
++
++#define OP_PROGRAM_VIA_BUF1	0x82
++#define OP_PROGRAM_VIA_BUF2	0x85
++
++struct dataflash_local
++{
++	int spi;			/* SPI chip-select number */
++
++	unsigned int page_size;		/* number of bytes per page */
++	unsigned short page_offset;	/* page offset in flash address */
++};
++
++
++/* Detected DataFlash devices */
++static struct mtd_info* mtd_devices[DATAFLASH_MAX_DEVICES];
++static int nr_devices = 0;
++
++/* ......................................................................... */
++
++#ifdef CONFIG_MTD_PARTITIONS
++
++static struct mtd_partition static_partitions_2M[] =
++{
++	{
++		.name		= "bootloader",
++		.offset		= 0,
++		.size		= 1 * 32 * 8 * 528,	/* 1st sector = 32 blocks * 8 pages * 528 bytes */
++		.mask_flags	= MTD_WRITEABLE,	/* read-only */
++	},
++	{
++		.name		= "kernel",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= 6 * 32 * 8 * 528,	/* 6 sectors */
++	},
++	{
++		.name		= "filesystem",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= MTDPART_SIZ_FULL,	/* rest = 9 sectors */
++	}
++};
++
++static struct mtd_partition static_partitions_4M[] =
++{
++	{
++		.name		= "bootloader",
++		.offset		= 0,
++		.size		= 1 * 64 * 8 * 528,	/* 1st sector = 64 blocks * 8 pages * 528 bytes */
++		.mask_flags	= MTD_WRITEABLE,	/* read-only */
++	},
++	{
++		.name		= "kernel",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= 4 * 64 * 8 * 528,	/* 4 sectors */
++	},
++	{
++		.name		= "filesystem",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= MTDPART_SIZ_FULL,	/* rest = 11 sectors */
++	}
++};
++
++#if defined(CONFIG_MACH_KAFA)
++static struct mtd_partition static_partitions_8M[] =
++{
++	{
++		name:		"romboot",
++		offset:		0,
++		size:		16 * 1056,	/* 160 Kb */
++		mask_flags:	MTD_WRITEABLE,		/* read-only */
++	},
++	{
++		name:		"uboot",
++		offset:		MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */
++		size:		128 * 1056,		/* 1 MB */
++	},
++	{
++		name:		"kernel",
++		offset:		MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */
++		size:		1024 * 1056,		/* 1 MB */
++	},
++	{
++		name:		"filesystem",
++		offset:		MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */
++		size:		MTDPART_SIZ_FULL,
++	}
++};
++
++#elif defined(CONFIG_MACH_MULTMDP)
++
++static struct mtd_partition static_partitions_8M[] =
++{
++	{
++		.name		= "bootloader",
++		.offset		= 0,
++		.size		= 12 * 1056,		/* 1st sector = 32 blocks * 8 pages * 1056 bytes */
++		.mask_flags	= MTD_WRITEABLE,	/* read-only */
++	},
++	{
++		.name		= "configuration",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= 20 * 1056,
++	},
++	{
++		.name		= "kernel",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= 1520 * 1056,
++	},
++	{
++		.name		= "filesystem",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= MTDPART_SIZ_FULL,
++	}
++};
++
++#else
++
++static struct mtd_partition static_partitions_8M[] =
++{
++	{
++		.name		= "bootloader",
++		.offset		= 0,
++		.size		= 1 * 32 * 8 * 1056,	/* 1st sector = 32 blocks * 8 pages * 1056 bytes */
++		.mask_flags	= MTD_WRITEABLE,	/* read-only */
++	},
++	{
++		.name		= "kernel",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= 5 * 32 * 8 * 1056,	/* 5 sectors */
++	},
++	{
++		.name		= "filesystem",
++		.offset		= MTDPART_OFS_NXTBLK,
++		.size		= MTDPART_SIZ_FULL,	/* rest = 26 sectors */
++	}
++};
++#endif
++
++static const char *part_probes[] = { "cmdlinepart", NULL, };
++
++#endif
++
++/* ......................................................................... */
++
++/* Allocate a single SPI transfer descriptor.  We're assuming that if multiple
++   SPI transfers occur at the same time, spi_access_bus() will serialize them.
++   If this is not valid, then either (i) each dataflash 'priv' structure
++   needs it's own transfer descriptor, (ii) we lock this one, or (iii) use
++   another mechanism.   */
++static struct spi_transfer_list* spi_transfer_desc;
++
++/*
++ * Perform a SPI transfer to access the DataFlash device.
++ */
++static int do_spi_transfer(int nr, char* tx, int tx_len, char* rx, int rx_len,
++		char* txnext, int txnext_len, char* rxnext, int rxnext_len)
++{
++	struct spi_transfer_list* list = spi_transfer_desc;
++
++	list->tx[0] = tx;	list->txlen[0] = tx_len;
++	list->rx[0] = rx;	list->rxlen[0] = rx_len;
++
++	list->tx[1] = txnext;	list->txlen[1] = txnext_len;
++	list->rx[1] = rxnext;	list->rxlen[1] = rxnext_len;
++
++	list->nr_transfers = nr;
++
++	return spi_transfer(list);
++}
++
++/* ......................................................................... */
++
++/*
++ * Poll the DataFlash device until it is READY.
++ */
++static void at91_dataflash_waitready(void)
++{
++	char* command = kmalloc(2, GFP_KERNEL);
++
++	if (!command)
++		return;
++
++	do {
++		command[0] = OP_READ_STATUS;
++		command[1] = 0;
++
++		do_spi_transfer(1, command, 2, command, 2, NULL, 0, NULL, 0);
++	} while ((command[1] & 0x80) == 0);
++
++	kfree(command);
++}
++
++/*
++ * Return the status of the DataFlash device.
++ */
++static unsigned short at91_dataflash_status(void)
++{
++	unsigned short status;
++	char* command = kmalloc(2, GFP_KERNEL);
++
++	if (!command)
++		return 0;
++
++	command[0] = OP_READ_STATUS;
++	command[1] = 0;
++
++	do_spi_transfer(1, command, 2, command, 2, NULL, 0, NULL, 0);
++	status = command[1];
++
++	kfree(command);
++	return status;
++}
++
++/* ......................................................................... */
++
++/*
++ * Erase blocks of flash.
++ */
++static int at91_dataflash_erase(struct mtd_info *mtd, struct erase_info *instr)
++{
++	struct dataflash_local *priv = (struct dataflash_local *) mtd->priv;
++	unsigned int pageaddr;
++	char* command;
++
++#ifdef DEBUG_DATAFLASH
++	printk("dataflash_erase: addr=%i len=%i\n", instr->addr, instr->len);
++#endif
++
++	/* Sanity checks */
++	if (instr->addr + instr->len > mtd->size)
++		return -EINVAL;
++	if ((instr->len % mtd->erasesize != 0) || (instr->len % priv->page_size != 0))
++		return -EINVAL;
++	if ((instr->addr % priv->page_size) != 0)
++		return -EINVAL;
++
++	command = kmalloc(4, GFP_KERNEL);
++	if (!command)
++		return -ENOMEM;
++
++	while (instr->len > 0) {
++		/* Calculate flash page address */
++		pageaddr = (instr->addr / priv->page_size) << priv->page_offset;
++
++		command[0] = OP_ERASE_PAGE;
++		command[1] = (pageaddr & 0x00FF0000) >> 16;
++		command[2] = (pageaddr & 0x0000FF00) >> 8;
++		command[3] = 0;
++#ifdef DEBUG_DATAFLASH
++		printk("ERASE: (%x) %x %x %x [%i]\n", command[0], command[1], command[2], command[3], pageaddr);
++#endif
++
++		/* Send command to SPI device */
++		spi_access_bus(priv->spi);
++		do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0);
++
++		at91_dataflash_waitready();		/* poll status until ready */
++		spi_release_bus(priv->spi);
++
++		instr->addr += priv->page_size;		/* next page */
++		instr->len -= priv->page_size;
++	}
++
++	kfree(command);
++
++	/* Inform MTD subsystem that erase is complete */
++	instr->state = MTD_ERASE_DONE;
++	if (instr->callback)
++		instr->callback(instr);
++
++	return 0;
++}
++
++/*
++ * Read from the DataFlash device.
++ *   from   : Start offset in flash device
++ *   len    : Amount to read
++ *   retlen : About of data actually read
++ *   buf    : Buffer containing the data
++ */
++static int at91_dataflash_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf)
++{
++	struct dataflash_local *priv = (struct dataflash_local *) mtd->priv;
++	unsigned int addr;
++	char* command;
++
++#ifdef DEBUG_DATAFLASH
++	printk("dataflash_read: %lli .. %lli\n", from, from+len);
++#endif
++
++	*retlen = 0;
++
++	/* Sanity checks */
++	if (!len)
++		return 0;
++	if (from + len > mtd->size)
++		return -EINVAL;
++
++	/* Calculate flash page/byte address */
++	addr = (((unsigned)from / priv->page_size) << priv->page_offset) + ((unsigned)from % priv->page_size);
++
++	command = kmalloc(8, GFP_KERNEL);
++	if (!command)
++		return -ENOMEM;
++
++	command[0] = OP_READ_CONTINUOUS;
++	command[1] = (addr & 0x00FF0000) >> 16;
++	command[2] = (addr & 0x0000FF00) >> 8;
++	command[3] = (addr & 0x000000FF);
++#ifdef DEBUG_DATAFLASH
++	printk("READ: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]);
++#endif
++
++	/* Send command to SPI device */
++	spi_access_bus(priv->spi);
++	do_spi_transfer(2, command, 8, command, 8, buf, len, buf, len);
++	spi_release_bus(priv->spi);
++
++	*retlen = len;
++	kfree(command);
++	return 0;
++}
++
++/*
++ * Write to the DataFlash device.
++ *   to     : Start offset in flash device
++ *   len    : Amount to write
++ *   retlen : Amount of data actually written
++ *   buf    : Buffer containing the data
++ */
++static int at91_dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, const u_char *buf)
++{
++	struct dataflash_local *priv = (struct dataflash_local *) mtd->priv;
++	unsigned int pageaddr, addr, offset, writelen;
++	size_t remaining;
++	u_char *writebuf;
++	unsigned short status;
++	int res = 0;
++	char* command;
++	char* tmpbuf = NULL;
++
++#ifdef DEBUG_DATAFLASH
++	printk("dataflash_write: %lli .. %lli\n", to, to+len);
++#endif
++
++	*retlen = 0;
++
++	/* Sanity checks */
++	if (!len)
++		return 0;
++	if (to + len > mtd->size)
++		return -EINVAL;
++
++	command = kmalloc(4, GFP_KERNEL);
++	if (!command)
++		return -ENOMEM;
++
++	pageaddr = ((unsigned)to / priv->page_size);
++	offset = ((unsigned)to % priv->page_size);
++	if (offset + len > priv->page_size)
++		writelen = priv->page_size - offset;
++	else
++		writelen = len;
++	writebuf = (u_char *)buf;
++	remaining = len;
++
++	/* Allocate temporary buffer */
++	tmpbuf = kmalloc(priv->page_size, GFP_KERNEL);
++	if (!tmpbuf) {
++		kfree(command);
++		return -ENOMEM;
++	}
++
++	/* Gain access to the SPI bus */
++	spi_access_bus(priv->spi);
++
++	while (remaining > 0) {
++#ifdef DEBUG_DATAFLASH
++		printk("write @ %i:%i len=%i\n", pageaddr, offset, writelen);
++#endif
++
++		/* (1) Transfer to Buffer1 */
++		if (writelen != priv->page_size) {
++			addr = pageaddr << priv->page_offset;
++			command[0] = OP_TRANSFER_BUF1;
++			command[1] = (addr & 0x00FF0000) >> 16;
++			command[2] = (addr & 0x0000FF00) >> 8;
++			command[3] = 0;
++#ifdef DEBUG_DATAFLASH
++			printk("TRANSFER: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]);
++#endif
++			do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0);
++			at91_dataflash_waitready();
++		}
++
++		/* (2) Program via Buffer1 */
++		addr = (pageaddr << priv->page_offset) + offset;
++		command[0] = OP_PROGRAM_VIA_BUF1;
++		command[1] = (addr & 0x00FF0000) >> 16;
++		command[2] = (addr & 0x0000FF00) >> 8;
++		command[3] = (addr & 0x000000FF);
++#ifdef DEBUG_DATAFLASH
++		printk("PROGRAM: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]);
++#endif
++		do_spi_transfer(2, command, 4, command, 4, writebuf, writelen, tmpbuf, writelen);
++		at91_dataflash_waitready();
++
++		/* (3) Compare to Buffer1 */
++		addr = pageaddr << priv->page_offset;
++		command[0] = OP_COMPARE_BUF1;
++		command[1] = (addr & 0x00FF0000) >> 16;
++		command[2] = (addr & 0x0000FF00) >> 8;
++		command[3] = 0;
++#ifdef DEBUG_DATAFLASH
++		printk("COMPARE: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]);
++#endif
++		do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0);
++		at91_dataflash_waitready();
++
++		/* Get result of the compare operation */
++		status = at91_dataflash_status();
++		if ((status & 0x40) == 1) {
++			printk("at91_dataflash: Write error on page %i\n", pageaddr);
++			remaining = 0;
++			res = -EIO;
++		}
++
++		remaining = remaining - writelen;
++		pageaddr++;
++		offset = 0;
++		writebuf += writelen;
++		*retlen += writelen;
++
++		if (remaining > priv->page_size)
++			writelen = priv->page_size;
++		else
++			writelen = remaining;
++	}
++
++	/* Release SPI bus */
++	spi_release_bus(priv->spi);
++
++	kfree(tmpbuf);
++	kfree(command);
++	return res;
++}
++
++/* ......................................................................... */
++
++/*
++ * Initialize and register DataFlash device with MTD subsystem.
++ */
++static int __init add_dataflash(int channel, char *name, int IDsize,
++		int nr_pages, int pagesize, int pageoffset)
++{
++	struct mtd_info *device;
++	struct dataflash_local *priv;
++#ifdef CONFIG_MTD_PARTITIONS
++	struct mtd_partition *mtd_parts = 0;
++	int mtd_parts_nr = 0;
++#endif
++
++	if (nr_devices >= DATAFLASH_MAX_DEVICES) {
++		printk(KERN_ERR "at91_dataflash: Too many devices detected\n");
++		return 0;
++	}
++
++	device = kmalloc(sizeof(struct mtd_info) + strlen(name) + 8, GFP_KERNEL);
++	if (!device)
++		return -ENOMEM;
++	memset(device, 0, sizeof(struct mtd_info));
++
++	device->name = (char *)&device[1];
++	sprintf(device->name, "%s.spi%d", name, channel);
++	device->size = nr_pages * pagesize;
++	device->erasesize = pagesize;
++	device->writesize = pagesize;
++	device->owner = THIS_MODULE;
++	device->type = MTD_DATAFLASH;
++	device->flags = MTD_WRITEABLE;
++	device->erase = at91_dataflash_erase;
++	device->read = at91_dataflash_read;
++	device->write = at91_dataflash_write;
++
++	priv = (struct dataflash_local *) kmalloc(sizeof(struct dataflash_local), GFP_KERNEL);
++	if (!priv) {
++		kfree(device);
++		return -ENOMEM;
++	}
++	memset(priv, 0, sizeof(struct dataflash_local));
++
++	priv->spi = channel;
++	priv->page_size = pagesize;
++	priv->page_offset = pageoffset;
++	device->priv = priv;
++
++	mtd_devices[nr_devices] = device;
++	nr_devices++;
++	printk("at91_dataflash: %s detected [spi%i] (%i bytes)\n", name, channel, device->size);
++
++#ifdef CONFIG_MTD_PARTITIONS
++#ifdef CONFIG_MTD_CMDLINE_PARTS
++	mtd_parts_nr = parse_mtd_partitions(device, part_probes, &mtd_parts, 0);
++#endif
++	if (mtd_parts_nr <= 0) {
++		switch (IDsize) {
++			case SZ_2M:
++				mtd_parts = static_partitions_2M;
++				mtd_parts_nr = ARRAY_SIZE(static_partitions_2M);
++				break;
++			case SZ_4M:
++				mtd_parts = static_partitions_4M;
++				mtd_parts_nr = ARRAY_SIZE(static_partitions_4M);
++				break;
++			case SZ_8M:
++				mtd_parts = static_partitions_8M;
++				mtd_parts_nr = ARRAY_SIZE(static_partitions_8M);
++				break;
++		}
++	}
++
++	if (mtd_parts_nr > 0) {
++#ifdef DATAFLASH_ALWAYS_ADD_DEVICE
++		add_mtd_device(device);
++#endif
++		return add_mtd_partitions(device, mtd_parts, mtd_parts_nr);
++	}
++#endif
++	return add_mtd_device(device);		/* add whole device */
++}
++
++/*
++ * Detect and initialize DataFlash device connected to specified SPI channel.
++ *
++ *   Device            Density         ID code                 Nr Pages        Page Size       Page offset
++ *   AT45DB011B        1Mbit   (128K)  xx0011xx (0x0c)         512             264             9
++ *   AT45DB021B        2Mbit   (256K)  xx0101xx (0x14)         1025            264             9
++ *   AT45DB041B        4Mbit   (512K)  xx0111xx (0x1c)         2048            264             9
++ *   AT45DB081B        8Mbit   (1M)    xx1001xx (0x24)         4096            264             9
++ *   AT45DB0161B       16Mbit  (2M)    xx1011xx (0x2c)         4096            528             10
++ *   AT45DB0321B       32Mbit  (4M)    xx1101xx (0x34)         8192            528             10
++ *   AT45DB0642        64Mbit  (8M)    xx1111xx (0x3c)         8192            1056            11
++ *   AT45DB1282        128Mbit (16M)   xx0100xx (0x10)         16384           1056            11
++ */
++static int __init at91_dataflash_detect(int channel)
++{
++	int res = 0;
++	unsigned short status;
++
++	spi_access_bus(channel);
++	status = at91_dataflash_status();
++	spi_release_bus(channel);
++	if (status != 0xff) {			/* no dataflash device there */
++		switch (status & 0x3c) {
++			case 0x0c:	/* 0 0 1 1 */
++				res = add_dataflash(channel, "AT45DB011B", SZ_128K, 512, 264, 9);
++				break;
++			case 0x14:	/* 0 1 0 1 */
++				res = add_dataflash(channel, "AT45DB021B", SZ_256K, 1025, 264, 9);
++				break;
++			case 0x1c:	/* 0 1 1 1 */
++				res = add_dataflash(channel, "AT45DB041B", SZ_512K, 2048, 264, 9);
++				break;
++			case 0x24:	/* 1 0 0 1 */
++				res = add_dataflash(channel, "AT45DB081B", SZ_1M, 4096, 264, 9);
++				break;
++			case 0x2c:	/* 1 0 1 1 */
++				res = add_dataflash(channel, "AT45DB161B", SZ_2M, 4096, 528, 10);
++				break;
++			case 0x34:	/* 1 1 0 1 */
++				res = add_dataflash(channel, "AT45DB321B", SZ_4M, 8192, 528, 10);
++				break;
++			case 0x3c:	/* 1 1 1 1 */
++				res = add_dataflash(channel, "AT45DB642", SZ_8M, 8192, 1056, 11);
++				break;
++// Currently unsupported since Atmel removed the "Main Memory Program via Buffer" commands.
++//			case 0x10:	/* 0 1 0 0 */
++//				res = add_dataflash(channel, "AT45DB1282", SZ_16M, 16384, 1056, 11);
++//				break;
++			default:
++				printk(KERN_ERR "at91_dataflash: Unknown device (%x)\n", status & 0x3c);
++		}
++	}
++
++	return res;
++}
++
++static int __init at91_dataflash_init(void)
++{
++	spi_transfer_desc = kmalloc(sizeof(struct spi_transfer_list), GFP_KERNEL);
++	if (!spi_transfer_desc)
++		return -ENOMEM;
++
++	/* DataFlash (SPI chip select 0) */
++	at91_dataflash_detect(0);
++
++#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
++	/* DataFlash card (SPI chip select 3) */
++	at91_dataflash_detect(3);
++#endif
++
++	return 0;
++}
++
++static void __exit at91_dataflash_exit(void)
++{
++	int i;
++
++	for (i = 0; i < DATAFLASH_MAX_DEVICES; i++) {
++		if (mtd_devices[i]) {
++#ifdef CONFIG_MTD_PARTITIONS
++			del_mtd_partitions(mtd_devices[i]);
++#else
++			del_mtd_device(mtd_devices[i]);
++#endif
++			kfree(mtd_devices[i]->priv);
++			kfree(mtd_devices[i]);
++		}
++	}
++	nr_devices = 0;
++	kfree(spi_transfer_desc);
++}
++
++
++module_init(at91_dataflash_init);
++module_exit(at91_dataflash_exit);
++
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("Andrew Victor");
++MODULE_DESCRIPTION("DataFlash driver for Atmel AT91RM9200");
+diff -urN -x CVS linux-2.6.21/drivers/mtd/nand/at91_nand.c linux-2.6-stable/drivers/mtd/nand/at91_nand.c
+--- linux-2.6.21/drivers/mtd/nand/at91_nand.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/mtd/nand/at91_nand.c	Tue May  8 12:13:31 2007
+@@ -82,6 +82,10 @@
+ 		at91_set_gpio_value(host->board->enable_pin, 1);
+ }
+ 
++#ifdef CONFIG_MTD_PARTITIONS
++const char *part_probes[] = { "cmdlinepart", NULL };
++#endif
++
+ /*
+  * Probe for the NAND device.
+  */
+@@ -151,6 +155,12 @@
+ #ifdef CONFIG_MTD_PARTITIONS
+ 	if (host->board->partition_info)
+ 		partitions = host->board->partition_info(mtd->size, &num_partitions);
++#ifdef CONFIG_MTD_CMDLINE_PARTS
++	else {
++		mtd->name = "at91_nand";
++		num_partitions = parse_mtd_partitions(mtd, part_probes, &partitions, 0);
++	}
++#endif
+ 
+ 	if ((!partitions) || (num_partitions == 0)) {
+ 		printk(KERN_ERR "at91_nand: No parititions defined, or unsupported device.\n");
+diff -urN -x CVS linux-2.6.21/drivers/net/arm/at91_ether.c linux-2.6-stable/drivers/net/arm/at91_ether.c
+--- linux-2.6.21/drivers/net/arm/at91_ether.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/net/arm/at91_ether.c	Tue May  8 12:13:31 2007
+@@ -225,6 +225,16 @@
+ 		if (!(phy & ((1 << 2) | 1)))
+ 			goto done;
+ 	}
++	else if (lp->phy_type == MII_T78Q21x3_ID) {			/* ack interrupt in Teridian PHY */
++		read_phy(lp->phy_address, MII_T78Q21INT_REG, &phy);
++		if (!(phy & ((1 << 2) | 1)))
++			goto done;
++	}
++	else if (lp->phy_type == MII_DP83848_ID) {
++		read_phy(lp->phy_address, MII_DPPHYSTS_REG, &phy);	/* ack interrupt in DP83848 PHY */
++		if (!(phy & (1 << 7)))
++			goto done;
++	}
+ 
+ 	update_linkspeed(dev, 0);
+ 
+@@ -280,6 +290,19 @@
+ 		dsintr = (1 << 10) | ( 1 << 8);
+ 		write_phy(lp->phy_address, MII_TPISTATUS, dsintr);
+ 	}
++	else if (lp->phy_type == MII_T78Q21x3_ID) {	/* for Teridian PHY */
++		read_phy(lp->phy_address, MII_T78Q21INT_REG, &dsintr);
++		dsintr = dsintr | 0x500;		/* set bits 8, 10 */
++		write_phy(lp->phy_address, MII_T78Q21INT_REG, dsintr);
++	}
++	else if (lp->phy_type == MII_DP83848_ID) {	/* National Semiconductor DP83848 PHY */
++		read_phy(lp->phy_address, MII_DPMISR_REG, &dsintr);
++		dsintr = dsintr | 0x3c;			/* set bits 2..5 */
++		write_phy(lp->phy_address, MII_DPMISR_REG, dsintr);
++		read_phy(lp->phy_address, MII_DPMICR_REG, &dsintr);
++		dsintr = dsintr | 0x3;			/* set bits 0,1 */
++		write_phy(lp->phy_address, MII_DPMICR_REG, dsintr);
++	}
+ 
+ 	disable_mdi();
+ 	spin_unlock_irq(&lp->lock);
+@@ -323,6 +346,19 @@
+ 		dsintr = ~((1 << 10) | (1 << 8));
+ 		write_phy(lp->phy_address, MII_TPISTATUS, dsintr);
+ 	}
++	else if (lp->phy_type == MII_T78Q21x3_ID) {	/* for Teridian PHY */
++		read_phy(lp->phy_address, MII_T78Q21INT_REG, &dsintr);
++		dsintr = dsintr & ~0x500;			/* clear bits 8, 10 */
++		write_phy(lp->phy_address, MII_T78Q21INT_REG, dsintr);
++	}
++	else if (lp->phy_type == MII_DP83848_ID) {	/* National Semiconductor DP83848 PHY */
++		read_phy(lp->phy_address, MII_DPMICR_REG, &dsintr);
++		dsintr = dsintr & ~0x3;				/* clear bits 0, 1 */
++		write_phy(lp->phy_address, MII_DPMICR_REG, dsintr);
++		read_phy(lp->phy_address, MII_DPMISR_REG, &dsintr);
++		dsintr = dsintr & ~0x3c;			/* clear bits 2..5 */
++		write_phy(lp->phy_address, MII_DPMISR_REG, dsintr);
++	}
+ 
+ 	disable_mdi();
+ 	spin_unlock_irq(&lp->lock);
+@@ -535,8 +571,8 @@
+ 		mc_filter[bitnr >> 5] |= 1 << (bitnr & 31);
+ 	}
+ 
+-	at91_emac_write(AT91_EMAC_HSH, mc_filter[0]);
+-	at91_emac_write(AT91_EMAC_HSL, mc_filter[1]);
++	at91_emac_write(AT91_EMAC_HSL, mc_filter[0]);
++	at91_emac_write(AT91_EMAC_HSH, mc_filter[1]);
+ }
+ 
+ /*
+@@ -943,14 +979,22 @@
+ 	struct net_device *dev;
+ 	struct at91_private *lp;
+ 	unsigned int val;
+-	int res;
++	struct resource *res;
++	int ret;
+ 
+ 	dev = alloc_etherdev(sizeof(struct at91_private));
+ 	if (!dev)
+ 		return -ENOMEM;
+ 
+-	dev->base_addr = AT91_VA_BASE_EMAC;
+-	dev->irq = AT91RM9200_ID_EMAC;
++	/* Get I/O base address and IRQ */
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	if (!res) {
++		free_netdev(dev);
++		return -ENODEV;
++	}
++	dev->base_addr = res->start;
++	dev->irq = platform_get_irq(pdev, 0);
++
+ 	SET_MODULE_OWNER(dev);
+ 
+ 	/* Install the interrupt handler */
+@@ -1023,12 +1067,12 @@
+ 	lp->phy_address = phy_address;	/* MDI address of PHY */
+ 
+ 	/* Register the network interface */
+-	res = register_netdev(dev);
+-	if (res) {
++	ret = register_netdev(dev);
++	if (ret) {
+ 		free_irq(dev->irq, dev);
+ 		free_netdev(dev);
+ 		dma_free_coherent(NULL, sizeof(struct recv_desc_bufs), lp->dlist, (dma_addr_t)lp->dlist_phys);
+-		return res;
++		return ret;
+ 	}
+ 
+ 	/* Determine current link speed */
+@@ -1063,10 +1107,16 @@
+ 		printk(KERN_INFO "%s: Broadcom BCM5221 PHY\n", dev->name);
+ 	else if (phy_type == MII_DP83847_ID)
+ 		printk(KERN_INFO "%s: National Semiconductor DP83847 PHY\n", dev->name);
++	else if (phy_type == MII_DP83848_ID)
++		printk(KERN_INFO "%s: National Semiconductor DP83848 PHY\n", dev->name);
+ 	else if (phy_type == MII_AC101L_ID)
+ 		printk(KERN_INFO "%s: Altima AC101L PHY\n", dev->name);
+ 	else if (phy_type == MII_KS8721_ID)
+ 		printk(KERN_INFO "%s: Micrel KS8721 PHY\n", dev->name);
++	else if (phy_type == MII_T78Q21x3_ID)
++		printk(KERN_INFO "%s: Teridian 78Q21x3 PHY\n", dev->name);
++	else if (phy_type == MII_LAN83C185_ID)
++		printk(KERN_INFO "%s: SMSC LAN83C185 PHY\n", dev->name);
+ 
+ 	return 0;
+ }
+@@ -1104,8 +1154,11 @@
+ 			case MII_RTL8201_ID:		/* Realtek RTL8201: PHY_ID1 = 0, PHY_ID2 = 0x8201 */
+ 			case MII_BCM5221_ID:		/* Broadcom BCM5221: PHY_ID1 = 0x40, PHY_ID2 = 0x61e0 */
+ 			case MII_DP83847_ID:		/* National Semiconductor DP83847:  */
++			case MII_DP83848_ID:		/* National Semiconductor DP83848:  */
+ 			case MII_AC101L_ID:		/* Altima AC101L: PHY_ID1 = 0x22, PHY_ID2 = 0x5520 */
+ 			case MII_KS8721_ID:		/* Micrel KS8721: PHY_ID1 = 0x22, PHY_ID2 = 0x1610 */
++			case MII_T78Q21x3_ID:		/* Teridian 78Q21x3: PHY_ID1 = 0x0E, PHY_ID2 = 7237 */
++			case MII_LAN83C185_ID:		/* SMSC LAN83C185: PHY_ID1 = 0x0007, PHY_ID2 = 0xC0A1 */
+ 				detected = at91ether_setup(phy_id, phy_address, pdev, ether_clk);
+ 				break;
+ 		}
+diff -urN -x CVS linux-2.6.21/drivers/net/arm/at91_ether.h linux-2.6-stable/drivers/net/arm/at91_ether.h
+--- linux-2.6.21/drivers/net/arm/at91_ether.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/net/arm/at91_ether.h	Tue May  8 12:13:31 2007
+@@ -17,39 +17,46 @@
+ 
+ 
+ /* Davicom 9161 PHY */
+-#define MII_DM9161_ID	0x0181b880
+-#define MII_DM9161A_ID	0x0181b8a0
+-
+-/* Davicom specific registers */
+-#define MII_DSCR_REG	16
+-#define MII_DSCSR_REG	17
+-#define MII_DSINTR_REG	21
++#define MII_DM9161_ID		0x0181b880
++#define MII_DM9161A_ID		0x0181b8a0
++#define MII_DSCR_REG		16
++#define MII_DSCSR_REG		17
++#define MII_DSINTR_REG		21
+ 
+ /* Intel LXT971A PHY */
+-#define MII_LXT971A_ID	0x001378E0
+-
+-/* Intel specific registers */
+-#define MII_ISINTE_REG	18
+-#define MII_ISINTS_REG	19
+-#define MII_LEDCTRL_REG	20
++#define MII_LXT971A_ID		0x001378E0
++#define MII_ISINTE_REG		18
++#define MII_ISINTS_REG		19
++#define MII_LEDCTRL_REG		20
+ 
+ /* Realtek RTL8201 PHY */
+-#define MII_RTL8201_ID	0x00008200
++#define MII_RTL8201_ID		0x00008200
+ 
+ /* Broadcom BCM5221 PHY */
+-#define MII_BCM5221_ID	0x004061e0
+-
+-/* Broadcom specific registers */
+-#define MII_BCMINTR_REG	26
++#define MII_BCM5221_ID		0x004061e0
++#define MII_BCMINTR_REG		26
+ 
+ /* National Semiconductor DP83847 */
+-#define MII_DP83847_ID	0x20005c30
++#define MII_DP83847_ID		0x20005c30
++
++/* National Semiconductor DP83848 */
++#define MII_DP83848_ID		0x20005c90
++#define MII_DPPHYSTS_REG	16
++#define MII_DPMICR_REG		17
++#define MII_DPMISR_REG		18
+ 
+ /* Altima AC101L PHY */
+-#define MII_AC101L_ID	0x00225520
++#define MII_AC101L_ID		0x00225520
+ 
+ /* Micrel KS8721 PHY */
+-#define MII_KS8721_ID	0x00221610
++#define MII_KS8721_ID		0x00221610
++
++/* Teridian 78Q2123/78Q2133 */
++#define MII_T78Q21x3_ID		0x000e7230
++#define MII_T78Q21INT_REG	17
++
++/* SMSC LAN83C185 */
++#define MII_LAN83C185_ID	0x0007C0A0
+ 
+ /* ........................................................................ */
+ 
+diff -urN -x CVS linux-2.6.21/drivers/pcmcia/at91_cf.c linux-2.6-stable/drivers/pcmcia/at91_cf.c
+--- linux-2.6.21/drivers/pcmcia/at91_cf.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/pcmcia/at91_cf.c	Tue May  8 12:13:31 2007
+@@ -332,20 +332,27 @@
+ 	struct at91_cf_data	*board = cf->board;
+ 
+ 	pcmcia_socket_dev_suspend(&pdev->dev, mesg);
++
+ 	if (device_may_wakeup(&pdev->dev)) {
+ 		enable_irq_wake(board->det_pin);
+ 		if (board->irq_pin)
+ 			enable_irq_wake(board->irq_pin);
+-	} else {
+-		disable_irq_wake(board->det_pin);
+-		if (board->irq_pin)
+-			disable_irq_wake(board->irq_pin);
+ 	}
++
+ 	return 0;
+ }
+ 
+ static int at91_cf_resume(struct platform_device *pdev)
+ {
++	struct at91_cf_socket	*cf = platform_get_drvdata(pdev);
++	struct at91_cf_data	*board = cf->board;
++
++	if (device_may_wakeup(&pdev->dev)) {
++		disable_irq_wake(board->det_pin);
++		if (board->irq_pin)
++			disable_irq_wake(board->irq_pin);
++	}
++
+ 	pcmcia_socket_dev_resume(&pdev->dev);
+ 	return 0;
+ }
+@@ -360,7 +367,6 @@
+ 		.name		= (char *) driver_name,
+ 		.owner		= THIS_MODULE,
+ 	},
+-	.probe		= at91_cf_probe,
+ 	.remove		= __exit_p(at91_cf_remove),
+ 	.suspend	= at91_cf_suspend,
+ 	.resume		= at91_cf_resume,
+@@ -370,7 +376,7 @@
+ 
+ static int __init at91_cf_init(void)
+ {
+-	return platform_driver_register(&at91_cf_driver);
++	return platform_driver_probe(&at91_cf_driver, at91_cf_probe);
+ }
+ module_init(at91_cf_init);
+ 
+diff -urN -x CVS linux-2.6.21/drivers/serial/atmel_serial.c linux-2.6-stable/drivers/serial/atmel_serial.c
+--- linux-2.6.21/drivers/serial/atmel_serial.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/serial/atmel_serial.c	Tue May  8 12:13:31 2007
+@@ -7,6 +7,8 @@
+  *  Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
+  *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+  *
++ *  DMA support added by Chip Coldwell.
++ *
+  * This program is free software; you can redistribute it and/or modify
+  * it under the terms of the GNU General Public License as published by
+  * the Free Software Foundation; either version 2 of the License, or
+@@ -33,6 +35,7 @@
+ #include <linux/sysrq.h>
+ #include <linux/tty_flip.h>
+ #include <linux/platform_device.h>
++#include <linux/dma-mapping.h>
+ #include <linux/atmel_pdc.h>
+ 
+ #include <asm/io.h>
+@@ -47,6 +50,11 @@
+ 
+ #include "atmel_serial.h"
+ 
++#define SUPPORT_PDC
++#define PDC_BUFFER_SIZE		(L1_CACHE_BYTES << 3)
++#warning "Revisit"
++#define PDC_RX_TIMEOUT		(3 * 10)		/* 3 bytes */
++
+ #if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+ #define SUPPORT_SYSRQ
+ #endif
+@@ -107,6 +115,13 @@
+ static int (*atmel_open_hook)(struct uart_port *);
+ static void (*atmel_close_hook)(struct uart_port *);
+ 
++struct atmel_dma_buffer {
++	unsigned char	*buf;
++	dma_addr_t	dma_addr;
++	size_t		dma_size;
++	unsigned int	ofs;
++};
++
+ /*
+  * We wrap our port structure around the generic uart_port.
+  */
+@@ -114,10 +129,20 @@
+ 	struct uart_port	uart;		/* uart */
+ 	struct clk		*clk;		/* uart clock */
+ 	unsigned short		suspended;	/* is port suspended? */
++
++	short			use_dma_rx;	/* enable PDC receiver */
++	short			pdc_rx_idx;	/* current PDC RX buffer */
++	struct atmel_dma_buffer	pdc_rx[2];	/* PDC receier */
++
++	short			use_dma_tx;	/* enable PDC transmitter */
++	struct atmel_dma_buffer	pdc_tx;		/* PDC transmitter */
+ };
+ 
+ static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
+ 
++#define PDC_RX_BUF(port)	&(port)->pdc_rx[(port)->pdc_rx_idx]
++#define PDC_RX_SWITCH(port)	(port)->pdc_rx_idx = !(port)->pdc_rx_idx
++
+ #ifdef SUPPORT_SYSRQ
+ static struct console atmel_console;
+ #endif
+@@ -205,7 +230,12 @@
+ {
+ 	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ 
+-	UART_PUT_IDR(port, ATMEL_US_TXRDY);
++	if (atmel_port->use_dma_tx) {
++		UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);		/* disable PDC transmit */
++		UART_PUT_IDR(port, ATMEL_US_ENDTX | ATMEL_US_TXBUFE);
++	}
++	else
++		UART_PUT_IDR(port, ATMEL_US_TXRDY);
+ }
+ 
+ /*
+@@ -215,7 +245,17 @@
+ {
+ 	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ 
+-	UART_PUT_IER(port, ATMEL_US_TXRDY);
++	if (atmel_port->use_dma_tx) {
++		if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN)
++			/* The transmitter is already running.  Yes, we
++			   really need this.*/
++			return;
++
++		UART_PUT_IER(port, ATMEL_US_ENDTX | ATMEL_US_TXBUFE);
++		UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);		/* re-enable PDC transmit */
++	}
++	else
++		UART_PUT_IER(port, ATMEL_US_TXRDY);
+ }
+ 
+ /*
+@@ -225,7 +265,12 @@
+ {
+ 	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ 
+-	UART_PUT_IDR(port, ATMEL_US_RXRDY);
++	if (atmel_port->use_dma_rx) {
++		UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS);		/* disable PDC receive */
++		UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
++	}
++	else
++		UART_PUT_IDR(port, ATMEL_US_RXRDY);
+ }
+ 
+ /*
+@@ -248,6 +293,134 @@
+ }
+ 
+ /*
++ * Receive data via the PDC.  A buffer has been fulled.
++ */
++static void atmel_pdc_endrx(struct uart_port *port)
++{
++	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
++	struct tty_struct *tty = port->info->tty;
++	struct atmel_dma_buffer *pdc = PDC_RX_BUF(atmel_port);
++	unsigned int count;
++
++	count = pdc->dma_size - pdc->ofs;
++	if (likely(count > 0)) {
++		dma_sync_single_for_cpu(port->dev, pdc->dma_addr, pdc->dma_size, DMA_FROM_DEVICE);
++		tty_insert_flip_string(tty, pdc->buf + pdc->ofs, count);
++		tty_flip_buffer_push(tty);
++
++		port->icount.rx += count;
++	}
++
++	/* Set this buffer as the next receive buffer */
++	pdc->ofs = 0;
++	UART_PUT_RNPR(port, pdc->dma_addr);
++	UART_PUT_RNCR(port, pdc->dma_size);
++
++	/* Switch to next buffer */
++	PDC_RX_SWITCH(atmel_port);		/* next PDC buffer */
++}
++
++/*
++ * Receive data via the PDC.  At least one byte was received, but the
++ * buffer was not full when the inter-character timeout expired.
++ */
++static void atmel_pdc_timeout(struct uart_port *port)
++{
++	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
++	struct tty_struct *tty = port->info->tty;
++	struct atmel_dma_buffer *pdc = PDC_RX_BUF(atmel_port);
++	/* unsigned */ int ofs, count;
++
++	ofs = UART_GET_RPR(port) - pdc->dma_addr;	/* current DMA adress */
++	count = ofs - pdc->ofs;
++
++	if (likely(count > 0)) {
++		dma_sync_single_for_cpu(port->dev, pdc->dma_addr, pdc->dma_size, DMA_FROM_DEVICE);
++		tty_insert_flip_string(tty, pdc->buf + pdc->ofs, count);
++		tty_flip_buffer_push(tty);
++
++		pdc->ofs = ofs;
++		port->icount.rx += count;
++	}
++
++	/* reset the UART timeout */
++	UART_PUT_CR(port, ATMEL_US_STTTO);
++}
++
++/*
++ * Deal with parity, framing and overrun errors.
++ */
++static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
++{
++	/* clear error */
++	UART_PUT_CR(port, ATMEL_US_RSTSTA);
++
++	if (status & ATMEL_US_RXBRK) {
++		status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);	/* ignore side-effect */
++		port->icount.brk++;
++	}
++	if (status & ATMEL_US_PARE)
++		port->icount.parity++;
++	if (status & ATMEL_US_FRAME)
++		port->icount.frame++;
++	if (status & ATMEL_US_OVRE)
++		port->icount.overrun++;
++}
++
++/*
++ * A transmission via the PDC is complete.
++ */
++static void atmel_pdc_endtx(struct uart_port *port)
++{
++	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
++	struct circ_buf *xmit = &port->info->xmit;
++	struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
++
++	xmit->tail += pdc->ofs;
++	if (xmit->tail >= SERIAL_XMIT_SIZE)
++		xmit->tail -= SERIAL_XMIT_SIZE;
++
++	port->icount.tx += pdc->ofs;
++	pdc->ofs = 0;
++
++	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
++		uart_write_wakeup(port);
++}
++
++/*
++ * The PDC transmitter is idle, so either start the next transfer or
++ * disable the transmitter.
++ */
++static void atmel_pdc_txbufe(struct uart_port *port)
++{
++	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
++	struct circ_buf *xmit = &port->info->xmit;
++	struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
++	int count;
++
++	if (!uart_circ_empty(xmit)) {
++		/* more to transmit - setup next transfer */
++		UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);			/* disable PDC transmit */
++		dma_sync_single_for_device(port->dev, pdc->dma_addr, pdc->dma_size, DMA_TO_DEVICE);
++
++		if (xmit->tail < xmit->head)
++			count = xmit->head - xmit->tail;
++		else
++			count = SERIAL_XMIT_SIZE - xmit->tail;
++		pdc->ofs = count;
++
++		UART_PUT_TPR(port, pdc->dma_addr + xmit->tail);
++		UART_PUT_TCR(port, count);
++		UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);			/* re-enable PDC transmit */
++	}
++	else {
++		/* nothing left to transmit - disable the transmitter */
++		UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);			/* disable PDC transmit */
++		UART_PUT_IDR(port, ATMEL_US_ENDTX | ATMEL_US_TXBUFE);
++	}
++}
++
++/*
+  * Characters received (called from interrupt handler)
+  */
+ static void atmel_rx_chars(struct uart_port *port)
+@@ -349,6 +522,14 @@
+ 	status = UART_GET_CSR(port);
+ 	pending = status & UART_GET_IMR(port);
+ 	while (pending) {
++		/* PDC receive */
++		if (pending & ATMEL_US_ENDRX)
++			atmel_pdc_endrx(port);
++		if (pending & ATMEL_US_TIMEOUT)
++			atmel_pdc_timeout(port);
++		if (atmel_port->use_dma_rx && pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE | ATMEL_US_FRAME | ATMEL_US_PARE))
++			atmel_pdc_rxerr(port, pending);
++
+ 		/* Interrupt receive */
+ 		if (pending & ATMEL_US_RXRDY)
+ 			atmel_rx_chars(port);
+@@ -363,6 +544,12 @@
+ 		if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC | ATMEL_US_CTSIC))
+ 			wake_up_interruptible(&port->info->delta_msr_wait);
+ 
++		/* PDC transmit */
++		if (pending & ATMEL_US_ENDTX)
++			atmel_pdc_endtx(port);
++		if (pending & ATMEL_US_TXBUFE)
++			atmel_pdc_txbufe(port);
++
+ 		/* Interrupt transmit */
+ 		if (pending & ATMEL_US_TXRDY)
+ 			atmel_tx_chars(port);
+@@ -401,6 +588,47 @@
+ 	}
+ 
+ 	/*
++	 * Initialize DMA (if necessary)
++	 */
++	if (atmel_port->use_dma_rx) {
++		int i;
++
++		for (i = 0; i < 2; i++) {
++			struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
++
++			pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
++			if (pdc->buf == NULL) {
++				if (i != 0) {
++					dma_unmap_single(port->dev, atmel_port->pdc_rx[0].dma_addr, PDC_BUFFER_SIZE, DMA_FROM_DEVICE);
++					kfree(atmel_port->pdc_rx[0].buf);
++				}
++				free_irq(port->irq, port);
++				return -ENOMEM;
++			}
++			pdc->dma_addr = dma_map_single(port->dev, pdc->buf, PDC_BUFFER_SIZE, DMA_FROM_DEVICE);
++			pdc->dma_size = PDC_BUFFER_SIZE;
++			pdc->ofs = 0;
++		}
++
++		atmel_port->pdc_rx_idx = 0;
++
++		UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr);
++		UART_PUT_RCR(port, PDC_BUFFER_SIZE);
++
++		UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr);
++		UART_PUT_RNCR(port, PDC_BUFFER_SIZE);
++	}
++	if (atmel_port->use_dma_tx) {
++		struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
++		struct circ_buf *xmit = &port->info->xmit;
++
++		pdc->buf = xmit->buf;
++		pdc->dma_addr = dma_map_single(port->dev, pdc->buf, SERIAL_XMIT_SIZE, DMA_TO_DEVICE);
++		pdc->dma_size = SERIAL_XMIT_SIZE;
++		pdc->ofs = 0;
++	}
++
++	/*
+ 	 * If there is a specific "open" function (to register
+ 	 * control line interrupts)
+ 	 */
+@@ -418,7 +646,15 @@
+ 	UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
+ 	UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);		/* enable xmit & rcvr */
+ 
+-	UART_PUT_IER(port, ATMEL_US_RXRDY);		/* enable receive only */
++	if (atmel_port->use_dma_rx) {
++		UART_PUT_RTOR(port, PDC_RX_TIMEOUT);		/* set UART timeout */
++		UART_PUT_CR(port, ATMEL_US_STTTO);
++
++		UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
++		UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);		/* enable PDC controller */
++	}
++	else
++		UART_PUT_IER(port, ATMEL_US_RXRDY);		/* enable receive only */
+ 
+ 	return 0;
+ }
+@@ -431,6 +667,31 @@
+ 	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ 
+ 	/*
++	 * Ensure everything is stopped.
++	 */
++	atmel_stop_rx(port);
++	atmel_stop_tx(port);
++
++	/*
++	 * Shut-down the DMA.
++	 */
++	if (atmel_port->use_dma_rx) {
++		int i;
++
++		for (i = 0; i < 2; i++) {
++			struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
++
++			dma_unmap_single(port->dev, pdc->dma_addr, pdc->dma_size, DMA_FROM_DEVICE);
++			kfree(pdc->buf);
++		}
++	}
++	if (atmel_port->use_dma_tx) {
++		struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
++
++		dma_unmap_single(port->dev, pdc->dma_addr, pdc->dma_size, DMA_TO_DEVICE);
++	}
++
++	/*
+ 	 * Disable all interrupts, port and break condition.
+ 	 */
+ 	UART_PUT_CR(port, ATMEL_US_RSTSTA);
+@@ -481,14 +742,20 @@
+  */
+ static void atmel_set_termios(struct uart_port *port, struct ktermios * termios, struct ktermios * old)
+ {
++	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ 	unsigned long flags;
+ 	unsigned int mode, imr, quot, baud;
+ 
++	/* Get current mode register */
++	mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP | ATMEL_US_PAR);
++
+ 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ 	quot = uart_get_divisor(port, baud);
+ 
+-	/* Get current mode register */
+-	mode = UART_GET_MR(port) & ~(ATMEL_US_CHRL | ATMEL_US_NBSTOP | ATMEL_US_PAR);
++	if (quot > 65535) {	/* BRGR is 16-bit, so switch to slower clock */
++		quot /= 8;
++		mode |= ATMEL_US_USCLKS_MCK_DIV8;
++	}
+ 
+ 	/* byte size */
+ 	switch (termios->c_cflag & CSIZE) {
+@@ -534,6 +801,9 @@
+ 	if (termios->c_iflag & (BRKINT | PARMRK))
+ 		port->read_status_mask |= ATMEL_US_RXBRK;
+ 
++	if (atmel_port->use_dma_rx)	/* need to enable error interrupts */
++		UART_PUT_IER(port, port->read_status_mask);
++
+ 	/*
+ 	 * Characters to ignore
+ 	 */
+@@ -712,6 +982,13 @@
+ 		clk_enable(atmel_port->clk);
+ 		port->uartclk = clk_get_rate(atmel_port->clk);
+ 	}
++
++#ifdef SUPPORT_PDC
++	atmel_port->use_dma_rx = data->use_dma_rx;
++	atmel_port->use_dma_tx = data->use_dma_tx;
++	if (atmel_port->use_dma_tx)
++		port->fifosize = PDC_BUFFER_SIZE;
++#endif
+ }
+ 
+ /*
+@@ -888,7 +1165,8 @@
+ 	struct uart_port *port = platform_get_drvdata(pdev);
+ 	struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
+ 
+-	if (device_may_wakeup(&pdev->dev) && !at91_suspend_entering_slow_clock())
++	if (device_may_wakeup(&pdev->dev)
++			&& !clk_must_disable(atmel_port->clk))
+ 		enable_irq_wake(port->irq);
+ 	else {
+ 		uart_suspend_port(&atmel_uart, port);
+diff -urN -x CVS linux-2.6.21/drivers/serial/atmel_serial.h linux-2.6-stable/drivers/serial/atmel_serial.h
+--- linux-2.6.21/drivers/serial/atmel_serial.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/serial/atmel_serial.h	Tue May  8 12:13:31 2007
+@@ -46,6 +46,9 @@
+ #define			ATMEL_US_USMODE_ISO7816_T1	6
+ #define			ATMEL_US_USMODE_IRDA		8
+ #define		ATMEL_US_USCLKS		(3   <<  4)		/* Clock Selection */
++#define			ATMEL_US_USCLKS_MCK		(0 <<  4)
++#define			ATMEL_US_USCLKS_MCK_DIV8	(1 <<  4)
++#define			ATMEL_US_USCLKS_SCK		(3 <<  4)
+ #define		ATMEL_US_CHRL		(3   <<  6)		/* Character Length */
+ #define			ATMEL_US_CHRL_5			(0 <<  6)
+ #define			ATMEL_US_CHRL_6			(1 <<  6)
+diff -urN -x CVS linux-2.6.21/drivers/spi/Kconfig linux-2.6-stable/drivers/spi/Kconfig
+--- linux-2.6.21/drivers/spi/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/spi/Kconfig	Tue May  8 14:31:24 2007
+@@ -54,6 +54,7 @@
+ config SPI_ATMEL
+ 	tristate "Atmel SPI Controller"
+ 	depends on (ARCH_AT91 || AVR32) && SPI_MASTER
++	select SPI_AT91_MANUAL_CS if ARCH_AT91RM9200
+ 	help
+ 	  This selects a driver for the Atmel SPI Controller, present on
+ 	  many AT32 (AVR32) and AT91 (ARM) chips.
+@@ -82,6 +83,24 @@
+ 	  inexpensive battery powered microcontroller evaluation board.
+ 	  This same cable can be used to flash new firmware.
+ 
++config SPI_AT91
++	tristate "AT91RM9200 Bitbang SPI Master"
++	depends on SPI_MASTER && ARCH_AT91RM9200 && !SPI_ATMEL && EXPERIMENTAL
++	select SPI_BITBANG
++	select SPI_AT91_MANUAL_CS
++	help
++	  This is dumb PIO bitbanging driver for the Atmel AT91RM9200.
++	  The SPI_ATMEL driver will be its replacement, using the native
++	  SPI hardware and its DMA controller.
++
++config SPI_AT91_MANUAL_CS
++	bool
++	depends on ARCH_AT91RM9200
++	help
++	  Works around an AT91RM9200 problem whereby the SPI chip-select
++	  will be wrongly disabled.  The workaround uses those pins as
++	  GPIOs instead of letting the SPI controller manage them.
++
+ config SPI_IMX
+ 	tristate "Freescale iMX SPI controller"
+ 	depends on SPI_MASTER && ARCH_IMX && EXPERIMENTAL
+diff -urN -x CVS linux-2.6.21/drivers/spi/Makefile linux-2.6-stable/drivers/spi/Makefile
+--- linux-2.6.21/drivers/spi/Makefile	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/spi/Makefile	Tue May  8 14:31:24 2007
+@@ -20,6 +20,7 @@
+ obj-$(CONFIG_SPI_MPC83xx)		+= spi_mpc83xx.o
+ obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o
+ obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx.o
++obj-$(CONFIG_SPI_AT91)			+= spi_at91_bitbang.o
+ # 	... add above this line ...
+ 
+ # SPI protocol drivers (device/link on bus)
+diff -urN -x CVS linux-2.6.21/drivers/spi/spi_at91_bitbang.c linux-2.6-stable/drivers/spi/spi_at91_bitbang.c
+--- linux-2.6.21/drivers/spi/spi_at91_bitbang.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/spi/spi_at91_bitbang.c	Tue May  8 14:31:24 2007
+@@ -0,0 +1,207 @@
++/*
++ * at91_spi.c - at91 SPI driver (BOOTSTRAP/BITBANG VERSION)
++ *
++ * Copyright (C) 2006 David Brownell
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
++ */
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++
++#include <linux/spi/spi.h>
++#include <linux/spi/spi_bitbang.h>
++
++#include <asm/arch/gpio.h>
++
++
++/*
++ * FIXME this bitbanging version is just to help bootstrap systems until
++ * there's a native SPI+IRQ+DMA controller driver ... such a driver should
++ * be a drop-in replacement for this one, and much faster.
++ *
++ * remember:
++ *
++ *	- other at91 parts (like at91sam9) have multiple controllers
++ *	  and different pin muxing; this version is at91rm9200 specfic.
++ *
++ *	- at91sam9261 SPI0 pins are directly muxed with MMC/SD pins.
++ *
++ *	- rm9200 spi chipselects drop wrongly, so the native driver
++ *	  will need to use gpios much like this does.
++ *
++ *	- real hardware only allows 8..16 bits per word, while this
++ *	  bitbanger allows 1..32 (incompatible superset).
++ *
++ *	- this disregards clock parameters.  with inlined gpio calls,
++ *	  gcc 3.4.4 produces about 1.5 mbit/sec, more than 2x faster
++ *	  than using the subroutined veresion from txrx_word().
++ *
++ *	- suspend/resume and <linux/clk.h> support is missing ...
++ */
++
++#define	spi_miso_bit	AT91_PIN_PA0
++#define	spi_mosi_bit	AT91_PIN_PA1
++#define	spi_sck_bit	AT91_PIN_PA2
++
++struct at91_spi {
++	struct spi_bitbang	bitbang;
++	struct platform_device	*pdev;
++};
++
++/*----------------------------------------------------------------------*/
++
++static inline void setsck(struct spi_device *spi, int is_on)
++{
++	at91_set_gpio_value(spi_sck_bit, is_on);
++}
++
++static inline void setmosi(struct spi_device *spi, int is_on)
++{
++	at91_set_gpio_value(spi_mosi_bit, is_on);
++}
++
++static inline int getmiso(struct spi_device *spi)
++{
++	return at91_get_gpio_value(spi_miso_bit);
++}
++
++static void at91_spi_chipselect(struct spi_device *spi, int is_active)
++{
++	unsigned long cs = (unsigned long) spi->controller_data;
++
++	/* set default clock polarity */
++	if (is_active)
++		setsck(spi, spi->mode & SPI_CPOL);
++
++	/* only support active-low (default) */
++	at91_set_gpio_value(cs, !is_active);
++}
++
++/*
++ * NOTE:  this is "as fast as we can"; it should be a function of
++ * the device clock ...
++ */
++#define	spidelay(X)	do{} while(0)
++
++#define	EXPAND_BITBANG_TXRX
++#include <linux/spi/spi_bitbang.h>
++
++static u32 at91_spi_txrx_word_mode0(struct spi_device *spi,
++		unsigned nsecs, u32 word, u8 bits)
++{
++	return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, 8);
++}
++
++static u32 at91_spi_txrx_word_mode1(struct spi_device *spi,
++		unsigned nsecs, u32 word, u8 bits)
++{
++	return bitbang_txrx_be_cpha1(spi, nsecs, 0, word, 8);
++}
++
++static u32 at91_spi_txrx_word_mode2(struct spi_device *spi,
++		unsigned nsecs, u32 word, u8 bits)
++{
++	return bitbang_txrx_be_cpha0(spi, nsecs, 1, word, 8);
++}
++
++static u32 at91_spi_txrx_word_mode3(struct spi_device *spi,
++		unsigned nsecs, u32 word, u8 bits)
++{
++	return bitbang_txrx_be_cpha1(spi, nsecs, 1, word, 8);
++}
++
++/*----------------------------------------------------------------------*/
++
++static int __init at91_spi_probe(struct platform_device *pdev)
++{
++	int			status;
++	struct spi_master	*master;
++	struct at91_spi		*at91_spi;
++
++	if (pdev->id != 0)	/* SPI0 bus */
++		return -EINVAL;
++
++	master = spi_alloc_master(&pdev->dev, sizeof *at91_spi);
++	if (!master)
++		return -ENOMEM;
++
++	at91_spi = spi_master_get_devdata(master);
++	at91_spi->pdev = pdev;
++	platform_set_drvdata(pdev, at91_spi);
++
++	/* SPI and bitbang hookup */
++	master->bus_num = 0;
++	master->num_chipselect = 4;
++
++	at91_spi->bitbang.master = spi_master_get(master);
++	at91_spi->bitbang.chipselect = at91_spi_chipselect;
++	at91_spi->bitbang.txrx_word[SPI_MODE_0] = at91_spi_txrx_word_mode0;
++	at91_spi->bitbang.txrx_word[SPI_MODE_1] = at91_spi_txrx_word_mode1;
++	at91_spi->bitbang.txrx_word[SPI_MODE_2] = at91_spi_txrx_word_mode2;
++	at91_spi->bitbang.txrx_word[SPI_MODE_3] = at91_spi_txrx_word_mode3;
++
++	status = spi_bitbang_start(&at91_spi->bitbang);
++	if (status < 0)
++		(void) spi_master_put(at91_spi->bitbang.master);
++
++	return status;
++}
++
++static int __exit at91_spi_remove(struct platform_device *pdev)
++{
++	struct at91_spi	*at91_spi = platform_get_drvdata(pdev);
++	int status;
++
++	/* stop() unregisters child devices too */
++	status = spi_bitbang_stop(&at91_spi->bitbang);
++	(void) spi_master_put(at91_spi->bitbang.master);
++
++	platform_set_drvdata(pdev, NULL);
++	return status;
++}
++
++static struct platform_driver at91_spi_driver = {
++	.probe		= at91_spi_probe,
++	.remove		= __exit_p(at91_spi_remove),
++	.driver		= {
++		.name	= "at91_spi",
++		.owner	= THIS_MODULE,
++	},
++};
++
++static int __init at91_spi_init(void)
++{
++	at91_set_gpio_output(spi_sck_bit, 0);
++	at91_set_gpio_output(spi_mosi_bit, 0);
++	at91_set_gpio_input(spi_miso_bit, 1 /* pullup */);
++
++	/* register driver */
++	return platform_driver_register(&at91_spi_driver);
++}
++
++static void __exit at91_spi_exit(void)
++{
++	platform_driver_unregister(&at91_spi_driver);
++}
++
++device_initcall(at91_spi_init);
++module_exit(at91_spi_exit);
++
++MODULE_ALIAS("at91_spi.0");
++
++MODULE_DESCRIPTION("AT91 SPI support (BOOTSTRAP/BITBANG VERSION)");
++MODULE_AUTHOR("David Brownell");
++MODULE_LICENSE("GPL");
+diff -urN -x CVS linux-2.6.21/drivers/usb/gadget/Kconfig linux-2.6-stable/drivers/usb/gadget/Kconfig
+--- linux-2.6.21/drivers/usb/gadget/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/usb/gadget/Kconfig	Wed May  9 10:20:54 2007
+@@ -189,7 +189,7 @@
+ 
+ config USB_GADGET_AT91
+ 	boolean "AT91 USB Device Port"
+-	depends on ARCH_AT91
++	depends on ARCH_AT91 && !ARCH_AT91SAM9RL
+ 	select USB_GADGET_SELECTED
+ 	help
+ 	   Many Atmel AT91 processors (such as the AT91RM2000) have a
+diff -urN -x CVS linux-2.6.21/drivers/usb/gadget/at91_udc.c linux-2.6-stable/drivers/usb/gadget/at91_udc.c
+--- linux-2.6.21/drivers/usb/gadget/at91_udc.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/usb/gadget/at91_udc.c	Tue May  8 12:13:31 2007
+@@ -1804,7 +1804,7 @@
+ 	 */
+ 	if ((!udc->suspended && udc->addr)
+ 			|| !wake
+-			|| at91_suspend_entering_slow_clock()) {
++			|| clk_must_disable(udc->fclk)) {
+ 		pullup(udc, 0);
+ 		wake = 0;
+ 	} else
+diff -urN -x CVS linux-2.6.21/drivers/usb/host/ohci-at91.c linux-2.6-stable/drivers/usb/host/ohci-at91.c
+--- linux-2.6.21/drivers/usb/host/ohci-at91.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/usb/host/ohci-at91.c	Tue May  8 12:13:31 2007
+@@ -299,7 +299,7 @@
+ 	 *
+ 	 * REVISIT: some boards will be able to turn VBUS off...
+ 	 */
+-	if (at91_suspend_entering_slow_clock()) {
++	if (clk_must_disable(fclk)) {
+ 		ohci_usb_reset (ohci);
+ 		at91_stop_clock();
+ 	}
+diff -urN -x CVS linux-2.6.21/drivers/video/Kconfig linux-2.6-stable/drivers/video/Kconfig
+--- linux-2.6.21/drivers/video/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/video/Kconfig	Thu May 10 12:34:41 2007
+@@ -663,6 +663,17 @@
+ 	  framebuffer.  Product specs at
+ 	  <http://www.erd.epson.com/vdc/html/products.htm>.
+ 
++config FB_S1D15605
++	tristate "Epson S1D15605 framebuffer support"
++	depends on FB
++	default m if MACH_KB9200
++	select FB_CFB_FILLRECT
++	select FB_CFB_COPYAREA
++	select FB_CFB_IMAGEBLIT
++	help
++	  Build in support for the S1D15605 Epson Research 128x64
++	  LCD controller as a framebuffer.
++
+ config FB_S1D13XXX
+ 	tristate "Epson S1D13XXX framebuffer support"
+ 	depends on FB
+@@ -674,6 +685,22 @@
+ 	  working with S1D13806). Product specs at
+ 	  <http://www.erd.epson.com/vdc/html/legacy_13xxx.htm>
+ 
++config FB_ATMEL
++	tristate "AT91/AT32 LCD Controller support"
++	depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || AVR32)
++	select FB_CFB_FILLRECT
++	select FB_CFB_COPYAREA
++	select FB_CFB_IMAGEBLIT
++	help
++	  This enables support for the AT91/AT32 LCD Controller.
++
++config FB_INTSRAM
++	bool "Frame Buffer in internal SRAM"
++	depends on FB_ATMEL && ARCH_AT91SAM9261
++	help
++	  Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
++	  to let frame buffer in external SDRAM.
++
+ config FB_NVIDIA
+ 	tristate "nVidia Framebuffer Support"
+ 	depends on FB && PCI
+diff -urN -x CVS linux-2.6.21/drivers/video/Makefile linux-2.6-stable/drivers/video/Makefile
+--- linux-2.6.21/drivers/video/Makefile	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/video/Makefile	Thu May 10 12:34:01 2007
+@@ -75,6 +75,8 @@
+ obj-$(CONFIG_FB_SA1100)           += sa1100fb.o
+ obj-$(CONFIG_FB_HIT)              += hitfb.o
+ obj-$(CONFIG_FB_EPSON1355)	  += epson1355fb.o
++obj-$(CONFIG_FB_S1D15605)	  += s1d15605fb.o
++obj-$(CONFIG_FB_ATMEL)            += atmel_lcdfb.o
+ obj-$(CONFIG_FB_PVR2)             += pvr2fb.o
+ obj-$(CONFIG_FB_VOODOO1)          += sstfb.o
+ obj-$(CONFIG_FB_ARMCLCD)	  += amba-clcd.o
+diff -urN -x CVS linux-2.6.21/drivers/video/atmel_lcdfb.c linux-2.6-stable/drivers/video/atmel_lcdfb.c
+--- linux-2.6.21/drivers/video/atmel_lcdfb.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/video/atmel_lcdfb.c	Thu May 10 12:34:01 2007
+@@ -0,0 +1,752 @@
++/*
++ *  Driver for AT91/AT32 LCD Controller
++ *
++ *  Copyright (C) 2007 Atmel Corporation
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file COPYING in the main directory of this archive for
++ * more details.
++ */
++
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++#include <linux/dma-mapping.h>
++#include <linux/interrupt.h>
++#include <linux/clk.h>
++#include <linux/fb.h>
++#include <linux/init.h>
++#include <linux/delay.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/cpu.h>
++#include <asm/arch/gpio.h>
++
++#include <video/atmel_lcdc.h>
++
++#define lcdc_readl(sinfo, reg)		__raw_readl((sinfo)->mmio+(reg))
++#define lcdc_writel(sinfo, reg, val)	__raw_writel((val), (sinfo)->mmio+(reg))
++
++/* configurable parameters */
++#define ATMEL_LCDC_CVAL_DEFAULT		0xc8
++#define ATMEL_LCDC_DMA_BURST_LEN	8
++
++#if defined(CONFIG_ARCH_AT91SAM9263)
++#define ATMEL_LCDC_FIFO_SIZE		2048
++#else
++#define ATMEL_LCDC_FIFO_SIZE		512
++#endif
++
++#if defined(CONFIG_ARCH_AT91)
++#define	ATMEL_LCDFB_FBINFO_DEFAULT	FBINFO_DEFAULT
++
++static inline void atmel_lcdfb_update_dma2d(struct atmel_lcdfb_info *sinfo,
++					struct fb_var_screeninfo *var)
++{
++
++}
++#elif defined(CONFIG_AVR32)
++#define	ATMEL_LCDFB_FBINFO_DEFAULT	(FBINFO_DEFAULT \
++					| FBINFO_PARTIAL_PAN_OK \
++					| FBINFO_HWACCEL_XPAN \
++					| FBINFO_HWACCEL_YPAN)
++
++static void atmel_lcdfb_update_dma2d(struct atmel_lcdfb_info *sinfo,
++				     struct fb_var_screeninfo *var)
++{
++	u32 dma2dcfg;
++	u32 pixeloff;
++
++	pixeloff = (var->xoffset * var->bits_per_pixel) & 0x1f;
++
++	dma2dcfg = ((var->xres_virtual - var->xres) * var->bits_per_pixel) / 8;
++	dma2dcfg |= pixeloff << ATMEL_LCDC_PIXELOFF_OFFSET;
++	lcdc_writel(sinfo, ATMEL_LCDC_DMA2DCFG, dma2dcfg);
++
++	/* Update configuration */
++	lcdc_writel(sinfo, ATMEL_LCDC_DMACON,
++		    lcdc_readl(sinfo, ATMEL_LCDC_DMACON)
++		    | ATMEL_LCDC_DMAUPDT);
++}
++#endif
++
++
++static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
++	.type		= FB_TYPE_PACKED_PIXELS,
++	.visual		= FB_VISUAL_TRUECOLOR,
++	.xpanstep	= 0,
++	.ypanstep	= 0,
++	.ywrapstep	= 0,
++	.accel		= FB_ACCEL_NONE,
++};
++
++
++static void atmel_lcdfb_update_dma(struct fb_info *info,
++			       struct fb_var_screeninfo *var)
++{
++	struct atmel_lcdfb_info *sinfo = info->par;
++	struct fb_fix_screeninfo *fix = &info->fix;
++	unsigned long dma_addr;
++
++	dma_addr = (fix->smem_start + var->yoffset * fix->line_length
++		    + var->xoffset * var->bits_per_pixel / 8);
++
++	dma_addr &= ~3UL;
++
++	/* Set framebuffer DMA base address and pixel offset */
++	lcdc_writel(sinfo, ATMEL_LCDC_DMABADDR1, dma_addr);
++
++	atmel_lcdfb_update_dma2d(sinfo, var);
++}
++
++static inline void atmel_lcdfb_free_video_memory(struct atmel_lcdfb_info *sinfo)
++{
++	struct fb_info *info = sinfo->info;
++
++	dma_free_writecombine(info->device, info->fix.smem_len,
++				info->screen_base, info->fix.smem_start);
++}
++
++/**
++ *	atmel_lcdfb_alloc_video_memory - Allocate framebuffer memory
++ *	@sinfo: the frame buffer to allocate memory for
++ */
++static int atmel_lcdfb_alloc_video_memory(struct atmel_lcdfb_info *sinfo)
++{
++	struct fb_info *info = sinfo->info;
++	struct fb_var_screeninfo *var = &info->var;
++
++	info->fix.smem_len = (var->xres_virtual * var->yres_virtual
++			    * ((var->bits_per_pixel + 7) / 8));
++
++	info->screen_base = dma_alloc_writecombine(info->device, info->fix.smem_len,
++					(dma_addr_t *)&info->fix.smem_start, GFP_KERNEL);
++
++	if (!info->screen_base) {
++		return -ENOMEM;
++	}
++
++	return 0;
++}
++
++/**
++ *      atmel_lcdfb_check_var - Validates a var passed in.
++ *      @var: frame buffer variable screen structure
++ *      @info: frame buffer structure that represents a single frame buffer
++ *
++ *	Checks to see if the hardware supports the state requested by
++ *	var passed in. This function does not alter the hardware
++ *	state!!!  This means the data stored in struct fb_info and
++ *	struct atmel_lcdfb_info do not change. This includes the var
++ *	inside of struct fb_info.  Do NOT change these. This function
++ *	can be called on its own if we intent to only test a mode and
++ *	not actually set it. The stuff in modedb.c is a example of
++ *	this. If the var passed in is slightly off by what the
++ *	hardware can support then we alter the var PASSED in to what
++ *	we can do. If the hardware doesn't support mode change a
++ *	-EINVAL will be returned by the upper layers. You don't need
++ *	to implement this function then. If you hardware doesn't
++ *	support changing the resolution then this function is not
++ *	needed. In this case the driver would just provide a var that
++ *	represents the static state the screen is in.
++ *
++ *	Returns negative errno on error, or zero on success.
++ */
++static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
++			     struct fb_info *info)
++{
++	struct device *dev = info->device;
++	struct atmel_lcdfb_info *sinfo = info->par;
++	unsigned long clk_value_khz;
++
++	clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
++
++	dev_dbg(dev, "%s:\n", __func__);
++	dev_dbg(dev, "  resolution: %ux%u\n", var->xres, var->yres);
++	dev_dbg(dev, "  pixclk:     %lu KHz\n", PICOS2KHZ(var->pixclock));
++	dev_dbg(dev, "  bpp:        %u\n", var->bits_per_pixel);
++	dev_dbg(dev, "  clk:        %lu KHz\n", clk_value_khz);
++
++	if ((PICOS2KHZ(var->pixclock) * var->bits_per_pixel / 8) > clk_value_khz) {
++		dev_err(dev, "%lu KHz pixel clock is too fast\n", PICOS2KHZ(var->pixclock));
++		return -EINVAL;
++	}
++
++	/* Force same alignment for each line */
++	var->xres = (var->xres + 3) & ~3UL;
++	var->xres_virtual = (var->xres_virtual + 3) & ~3UL;
++
++	var->red.msb_right = var->green.msb_right = var->blue.msb_right = 0;
++	var->transp.msb_right = 0;
++	var->transp.offset = var->transp.length = 0;
++	var->xoffset = var->yoffset = 0;
++
++	switch (var->bits_per_pixel) {
++	case 2:
++	case 4:
++	case 8:
++		var->red.offset = var->green.offset = var->blue.offset = 0;
++		var->red.length = var->green.length = var->blue.length
++			= var->bits_per_pixel;
++		break;
++	case 15:
++	case 16:
++		var->red.offset = 0;
++		var->green.offset = 5;
++		var->blue.offset = 10;
++		var->red.length = var->green.length = var->blue.length = 5;
++		break;
++	case 24:
++	case 32:
++		var->red.offset = 0;
++		var->green.offset = 8;
++		var->blue.offset = 16;
++		var->red.length = var->green.length = var->blue.length = 8;
++		break;
++	default:
++		dev_err(dev, "color depth %d not supported\n",
++					var->bits_per_pixel);
++		return -EINVAL;
++	}
++
++	return 0;
++}
++
++/**
++ *      atmel_lcdfb_set_par - Alters the hardware state.
++ *      @info: frame buffer structure that represents a single frame buffer
++ *
++ *	Using the fb_var_screeninfo in fb_info we set the resolution
++ *	of the this particular framebuffer. This function alters the
++ *	par AND the fb_fix_screeninfo stored in fb_info. It doesn't
++ *	not alter var in fb_info since we are using that data. This
++ *	means we depend on the data in var inside fb_info to be
++ *	supported by the hardware.  atmel_lcdfb_check_var is always called
++ *	before atmel_lcdfb_set_par to ensure this.  Again if you can't
++ *	change the resolution you don't need this function.
++ *
++ */
++static int atmel_lcdfb_set_par(struct fb_info *info)
++{
++	struct atmel_lcdfb_info *sinfo = info->par;
++	unsigned long value;
++	unsigned long clk_value_khz;
++
++	dev_dbg(info->device, "%s:\n", __func__);
++	dev_dbg(info->device, "  * resolution: %ux%u (%ux%u virtual)\n",
++		 info->var.xres, info->var.yres,
++		 info->var.xres_virtual, info->var.yres_virtual);
++
++	/* Turn off the LCD controller and the DMA controller */
++	lcdc_writel(sinfo, ATMEL_LCDC_PWRCON, sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
++
++	lcdc_writel(sinfo, ATMEL_LCDC_DMACON, 0);
++
++	if (info->var.bits_per_pixel <= 8)
++		info->fix.visual = FB_VISUAL_PSEUDOCOLOR;
++	else
++		info->fix.visual = FB_VISUAL_TRUECOLOR;
++
++	info->fix.line_length = info->var.xres_virtual * (info->var.bits_per_pixel / 8);
++
++	/* Re-initialize the DMA engine... */
++	dev_dbg(info->device, "  * update DMA engine\n");
++	atmel_lcdfb_update_dma(info, &info->var);
++
++	/* ...set frame size and burst length = 8 words (?) */
++	value = (info->var.yres * info->var.xres * info->var.bits_per_pixel) / 32;
++	value |= ((ATMEL_LCDC_DMA_BURST_LEN - 1) << ATMEL_LCDC_BLENGTH_OFFSET);
++	lcdc_writel(sinfo, ATMEL_LCDC_DMAFRMCFG, value);
++
++	/* Now, the LCDC core... */
++
++	/* Set pixel clock */
++	clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
++
++	value = clk_value_khz / PICOS2KHZ(info->var.pixclock);
++
++	if (clk_value_khz % PICOS2KHZ(info->var.pixclock))
++		value++;
++
++	value = (value / 2) - 1;
++
++	if (value <= 0) {
++		dev_notice(info->device, "Bypassing pixel clock divider\n");
++		lcdc_writel(sinfo, ATMEL_LCDC_LCDCON1, ATMEL_LCDC_BYPASS);
++	} else
++		lcdc_writel(sinfo, ATMEL_LCDC_LCDCON1, value << ATMEL_LCDC_CLKVAL_OFFSET);
++
++	/* Initialize control register 2 */
++	value = sinfo->default_lcdcon2;
++
++	if (!(info->var.sync & FB_SYNC_HOR_HIGH_ACT))
++		value |= ATMEL_LCDC_INVLINE_INVERTED;
++	if (!(info->var.sync & FB_SYNC_VERT_HIGH_ACT))
++		value |= ATMEL_LCDC_INVFRAME_INVERTED;
++
++	switch (info->var.bits_per_pixel) {
++		case 1:	value |= ATMEL_LCDC_PIXELSIZE_1; break;
++		case 2: value |= ATMEL_LCDC_PIXELSIZE_2; break;
++		case 4: value |= ATMEL_LCDC_PIXELSIZE_4; break;
++		case 8: value |= ATMEL_LCDC_PIXELSIZE_8; break;
++		case 15: /* fall through */
++		case 16: value |= ATMEL_LCDC_PIXELSIZE_16; break;
++		case 24: value |= ATMEL_LCDC_PIXELSIZE_24; break;
++		case 32: value |= ATMEL_LCDC_PIXELSIZE_32; break;
++		default: BUG(); break;
++	}
++	dev_dbg(info->device, "  * LCDCON2 = %08lx\n", value);
++	lcdc_writel(sinfo, ATMEL_LCDC_LCDCON2, value);
++
++	/* Vertical timing */
++	value = (info->var.vsync_len - 1) << ATMEL_LCDC_VPW_OFFSET;
++	value |= info->var.upper_margin << ATMEL_LCDC_VBP_OFFSET;
++	value |= info->var.lower_margin;
++	dev_dbg(info->device, "  * LCDTIM1 = %08lx\n", value);
++	lcdc_writel(sinfo, ATMEL_LCDC_TIM1, value);
++
++	/* Horizontal timing */
++	value = (info->var.right_margin - 1) << ATMEL_LCDC_HFP_OFFSET;
++	value |= (info->var.hsync_len - 1) << ATMEL_LCDC_HPW_OFFSET;
++	value |= (info->var.left_margin - 1);
++	dev_dbg(info->device, "  * LCDTIM2 = %08lx\n", value);
++	lcdc_writel(sinfo, ATMEL_LCDC_TIM2, value);
++
++	/* Display size */
++	value = (info->var.xres - 1) << ATMEL_LCDC_HOZVAL_OFFSET;
++	value |= info->var.yres - 1;
++	lcdc_writel(sinfo, ATMEL_LCDC_LCDFRMCFG, value);
++
++	/* FIFO Threshold: Use formula from data sheet */
++	value = ATMEL_LCDC_FIFO_SIZE - (2 * ATMEL_LCDC_DMA_BURST_LEN + 3);
++	lcdc_writel(sinfo, ATMEL_LCDC_FIFO, value);
++
++	/* Toggle LCD_MODE every frame */
++	lcdc_writel(sinfo, ATMEL_LCDC_MVAL, 0);
++
++	/* Disable all interrupts */
++	lcdc_writel(sinfo, ATMEL_LCDC_IDR, ~0UL);
++
++	/* Set contrast */
++	value = ATMEL_LCDC_PS_DIV8 | ATMEL_LCDC_POL_POSITIVE | ATMEL_LCDC_ENA_PWMENABLE;
++	lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, value);
++	lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
++	/* ...wait for DMA engine to become idle... */
++	while (lcdc_readl(sinfo, ATMEL_LCDC_DMACON) & ATMEL_LCDC_DMABUSY)
++		msleep(10);
++
++	dev_dbg(info->device, "  * re-enable DMA engine\n");
++	/* ...and enable it with updated configuration */
++	lcdc_writel(sinfo, ATMEL_LCDC_DMACON, sinfo->default_dmacon);
++
++	dev_dbg(info->device, "  * re-enable LCDC core\n");
++	lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
++		(sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET) | ATMEL_LCDC_PWR);
++
++	dev_dbg(info->device, "  * DONE\n");
++
++	return 0;
++}
++
++static inline unsigned int chan_to_field(unsigned int chan, const struct fb_bitfield *bf)
++{
++	chan &= 0xffff;
++	chan >>= 16 - bf->length;
++	return chan << bf->offset;
++}
++
++/**
++ *  	atmel_lcdfb_setcolreg - Optional function. Sets a color register.
++ *      @regno: Which register in the CLUT we are programming
++ *      @red: The red value which can be up to 16 bits wide
++ *	@green: The green value which can be up to 16 bits wide
++ *	@blue:  The blue value which can be up to 16 bits wide.
++ *	@transp: If supported the alpha value which can be up to 16 bits wide.
++ *      @info: frame buffer info structure
++ *
++ *  	Set a single color register. The values supplied have a 16 bit
++ *  	magnitude which needs to be scaled in this function for the hardware.
++ *	Things to take into consideration are how many color registers, if
++ *	any, are supported with the current color visual. With truecolor mode
++ *	no color palettes are supported. Here a psuedo palette is created
++ *	which we store the value in pseudo_palette in struct fb_info. For
++ *	pseudocolor mode we have a limited color palette. To deal with this
++ *	we can program what color is displayed for a particular pixel value.
++ *	DirectColor is similar in that we can program each color field. If
++ *	we have a static colormap we don't need to implement this function.
++ *
++ *	Returns negative errno on error, or zero on success. In an
++ *	ideal world, this would have been the case, but as it turns
++ *	out, the other drivers return 1 on failure, so that's what
++ *	we're going to do.
++ */
++static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
++			     unsigned int green, unsigned int blue,
++			     unsigned int transp, struct fb_info *info)
++{
++	struct atmel_lcdfb_info *sinfo = info->par;
++	unsigned int val;
++	u32 *pal;
++	int ret = 1;
++
++	if (info->var.grayscale)
++		red = green = blue = (19595 * red + 38470 * green
++				      + 7471 * blue) >> 16;
++
++	switch (info->fix.visual) {
++	case FB_VISUAL_TRUECOLOR:
++		if (regno < 16) {
++			pal = info->pseudo_palette;
++
++			val  = chan_to_field(red, &info->var.red);
++			val |= chan_to_field(green, &info->var.green);
++			val |= chan_to_field(blue, &info->var.blue);
++
++			pal[regno] = val;
++			ret = 0;
++		}
++		break;
++
++	case FB_VISUAL_PSEUDOCOLOR:
++		if (regno < 256) {
++			val  = ((red   >> 11) & 0x001f);
++			val |= ((green >>  6) & 0x03e0);
++			val |= ((blue  >>  1) & 0x7c00);
++
++			/*
++			 * TODO: intensity bit. Maybe something like
++			 *   ~(red[10] ^ green[10] ^ blue[10]) & 1
++			 */
++
++			lcdc_writel(sinfo, ATMEL_LCDC_LUT(regno), val);
++			ret = 0;
++		}
++		break;
++	}
++
++	return ret;
++}
++
++static int atmel_lcdfb_pan_display(struct fb_var_screeninfo *var,
++			       struct fb_info *info)
++{
++	dev_dbg(info->device, "%s\n", __func__);
++
++	atmel_lcdfb_update_dma(info, var);
++
++	return 0;
++}
++
++static struct fb_ops atmel_lcdfb_ops = {
++	.owner		= THIS_MODULE,
++	.fb_check_var	= atmel_lcdfb_check_var,
++	.fb_set_par	= atmel_lcdfb_set_par,
++	.fb_setcolreg	= atmel_lcdfb_setcolreg,
++	.fb_pan_display	= atmel_lcdfb_pan_display,
++	.fb_fillrect	= cfb_fillrect,
++	.fb_copyarea	= cfb_copyarea,
++	.fb_imageblit	= cfb_imageblit,
++};
++
++static irqreturn_t atmel_lcdfb_interrupt(int irq, void *dev_id)
++{
++	struct fb_info *info = dev_id;
++	struct atmel_lcdfb_info *sinfo = info->par;
++	u32 status;
++
++	status = lcdc_readl(sinfo, ATMEL_LCDC_ISR);
++	lcdc_writel(sinfo, ATMEL_LCDC_IDR, status);
++	return IRQ_HANDLED;
++}
++
++static int __init atmel_lcdfb_init_fbinfo(struct atmel_lcdfb_info *sinfo)
++{
++	struct fb_info *info = sinfo->info;
++	int ret = 0;
++
++	memset_io(info->screen_base, 0, info->fix.smem_len);
++	info->var.activate |= FB_ACTIVATE_FORCE | FB_ACTIVATE_NOW;
++
++	dev_info(info->device,
++	       "%luKiB frame buffer at %08lx (mapped at %p)\n",
++	       (unsigned long)info->fix.smem_len / 1024,
++	       (unsigned long)info->fix.smem_start,
++	       info->screen_base);
++
++	/* Allocate colormap */
++	ret = fb_alloc_cmap(&info->cmap, 256, 0);
++	if (ret < 0)
++		dev_err(info->device, "Alloc color map failed\n");
++
++	return ret;
++}
++
++static void atmel_lcdfb_start_clock(struct atmel_lcdfb_info *sinfo)
++{
++	if (sinfo->bus_clk)
++		clk_enable(sinfo->bus_clk);
++	clk_enable(sinfo->lcdc_clk);
++}
++
++static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
++{
++	if (sinfo->bus_clk)
++		clk_disable(sinfo->bus_clk);
++	clk_disable(sinfo->lcdc_clk);
++}
++
++
++static int __init atmel_lcdfb_probe(struct platform_device *pdev)
++{
++	struct device *dev = &pdev->dev;
++	struct fb_info *info;
++	struct atmel_lcdfb_info *sinfo;
++	struct atmel_lcdfb_info *pdata_sinfo;
++	struct resource *regs = NULL;
++	struct resource *map = NULL;
++	int ret;
++
++	dev_dbg(dev, "%s BEGIN\n", __func__);
++
++	ret = -ENOMEM;
++	info = framebuffer_alloc(sizeof(struct atmel_lcdfb_info), dev);
++	if (!info) {
++		dev_err(dev, "cannot allocate memory\n");
++		goto out;
++	}
++
++	sinfo = info->par;
++
++	if (dev->platform_data) {
++		pdata_sinfo = (struct atmel_lcdfb_info *)dev->platform_data;
++		sinfo->default_bpp = pdata_sinfo->default_bpp;
++		sinfo->default_dmacon = pdata_sinfo->default_dmacon;
++		sinfo->default_lcdcon2 = pdata_sinfo->default_lcdcon2;
++		sinfo->default_monspecs = pdata_sinfo->default_monspecs;
++		sinfo->atmel_lcdfb_power_control = pdata_sinfo->atmel_lcdfb_power_control;
++		sinfo->guard_time = pdata_sinfo->guard_time;
++	} else {
++		dev_err(dev, "cannot get default configuration\n");
++		goto free_info;
++	}
++	sinfo->info = info;
++	sinfo->pdev = pdev;
++
++	strcpy(info->fix.id, sinfo->pdev->name);
++	info->flags = ATMEL_LCDFB_FBINFO_DEFAULT;
++	info->pseudo_palette = sinfo->pseudo_palette;
++	info->fbops = &atmel_lcdfb_ops;
++
++	memcpy(&info->monspecs, sinfo->default_monspecs, sizeof(info->monspecs));
++	info->fix = atmel_lcdfb_fix;
++
++	/* Enable LCDC Clocks */
++	if (cpu_is_at91sam9261()) {
++		sinfo->bus_clk = clk_get(dev, "hck1");
++		if (IS_ERR(sinfo->bus_clk)) {
++			ret = PTR_ERR(sinfo->bus_clk);
++			goto free_info;
++		}
++	}
++	sinfo->lcdc_clk = clk_get(dev, "lcdc_clk");
++	if (IS_ERR(sinfo->lcdc_clk)) {
++		ret = PTR_ERR(sinfo->lcdc_clk);
++		goto put_bus_clk;
++	}
++	atmel_lcdfb_start_clock(sinfo);
++
++	ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
++			info->monspecs.modedb_len, info->monspecs.modedb,
++			sinfo->default_bpp);
++	if (!ret) {
++		dev_err(dev, "no suitable video mode found\n");
++		goto stop_clk;
++	}
++
++
++	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	if (!regs) {
++		dev_err(dev, "resources unusable\n");
++		ret = -ENXIO;
++		goto stop_clk;
++	}
++
++	sinfo->irq_base = platform_get_irq(pdev, 0);
++	if (sinfo->irq_base < 0) {
++		dev_err(dev, "unable to get irq\n");
++		ret = sinfo->irq_base;
++		goto stop_clk;
++	}
++
++	/* Initialize video memory */
++	map = platform_get_resource(pdev, IORESOURCE_MEM, 1);
++	if (map) {
++		/* use a pre-allocated memory buffer */
++		info->fix.smem_start = map->start;
++		info->fix.smem_len = map->end - map->start + 1;
++		if (!request_mem_region(info->fix.smem_start,
++					info->fix.smem_len, pdev->name)) {
++			ret = -EBUSY;
++			goto stop_clk;
++		}
++
++		info->screen_base = ioremap(info->fix.smem_start, info->fix.smem_len);
++		if (!info->screen_base)
++			goto release_intmem;
++	} else {
++		/* alocate memory buffer */
++		ret = atmel_lcdfb_alloc_video_memory(sinfo);
++		if (ret < 0) {
++			dev_err(dev, "cannot allocate framebuffer: %d\n", ret);
++			goto stop_clk;
++		}
++	}
++
++	/* LCDC registers */
++	info->fix.mmio_start = regs->start;
++	info->fix.mmio_len = regs->end - regs->start + 1;
++
++	if (!request_mem_region(info->fix.mmio_start,
++				info->fix.mmio_len, pdev->name)) {
++		ret = -EBUSY;
++		goto free_fb;
++	}
++
++	sinfo->mmio = ioremap(info->fix.mmio_start, info->fix.mmio_len);
++	if (!sinfo->mmio) {
++		dev_err(dev, "cannot map LCDC registers\n");
++		goto release_mem;
++	}
++
++	/* interrupt */
++	ret = request_irq(sinfo->irq_base, atmel_lcdfb_interrupt, 0, pdev->name, info);
++	if (ret) {
++		dev_err(dev, "request_irq failed: %d\n", ret);
++		goto unmap_mmio;
++	}
++
++	ret = atmel_lcdfb_init_fbinfo(sinfo);
++	if (ret < 0) {
++		dev_err(dev, "init fbinfo failed: %d\n", ret);
++		goto unregister_irqs;
++	}
++
++	/*
++	 * This makes sure that our colour bitfield
++	 * descriptors are correctly initialised.
++	 */
++	atmel_lcdfb_check_var(&info->var, info);
++
++	ret = fb_set_var(info, &info->var);
++	if (ret) {
++		dev_warn(dev, "unable to set display parameters\n");
++		goto free_cmap;
++	}
++
++	dev_set_drvdata(dev, info);
++
++	/*
++	 * Tell the world that we're ready to go
++	 */
++	ret = register_framebuffer(info);
++	if (ret < 0) {
++		dev_err(dev, "failed to register framebuffer device: %d\n", ret);
++		goto free_cmap;
++	}
++
++	/* Power up the LCDC screen */
++	if (sinfo->atmel_lcdfb_power_control)
++		sinfo->atmel_lcdfb_power_control(1);
++
++	dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %lu\n",
++		       info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
++
++	return 0;
++
++
++free_cmap:
++	fb_dealloc_cmap(&info->cmap);
++unregister_irqs:
++	free_irq(sinfo->irq_base, info);
++unmap_mmio:
++	iounmap(sinfo->mmio);
++release_mem:
++ 	release_mem_region(info->fix.mmio_start, info->fix.mmio_len);
++free_fb:
++	if (map)
++		iounmap(info->screen_base);
++	else
++		atmel_lcdfb_free_video_memory(sinfo);
++
++release_intmem:
++	if (map)
++		release_mem_region(info->fix.smem_start, info->fix.smem_len);
++stop_clk:
++	atmel_lcdfb_stop_clock(sinfo);
++	clk_put(sinfo->lcdc_clk);
++put_bus_clk:
++	if (sinfo->bus_clk)
++		clk_put(sinfo->bus_clk);
++free_info:
++	framebuffer_release(info);
++out:
++	dev_dbg(dev, "%s FAILED\n", __func__);
++	return ret;
++}
++
++static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
++{
++	struct device *dev = &pdev->dev;
++	struct fb_info *info = dev_get_drvdata(dev);
++	struct atmel_lcdfb_info *sinfo = info->par;
++
++	if (!sinfo)
++		return 0;
++
++	if (sinfo->atmel_lcdfb_power_control)
++		sinfo->atmel_lcdfb_power_control(0);
++	unregister_framebuffer(info);
++	atmel_lcdfb_stop_clock(sinfo);
++	clk_put(sinfo->lcdc_clk);
++	if (sinfo->bus_clk)
++		clk_put(sinfo->bus_clk);
++	fb_dealloc_cmap(&info->cmap);
++	free_irq(sinfo->irq_base, info);
++	iounmap(sinfo->mmio);
++ 	release_mem_region(info->fix.mmio_start, info->fix.mmio_len);
++	if (platform_get_resource(pdev, IORESOURCE_MEM, 1)) {
++		iounmap(info->screen_base);
++		release_mem_region(info->fix.smem_start, info->fix.smem_len);
++	} else {
++		atmel_lcdfb_free_video_memory(sinfo);
++	}
++
++	dev_set_drvdata(dev, NULL);
++	framebuffer_release(info);
++
++	return 0;
++}
++
++static struct platform_driver atmel_lcdfb_driver = {
++	.remove		= __exit_p(atmel_lcdfb_remove),
++	.driver		= {
++		.name	= "atmel_lcdfb",
++		.owner	= THIS_MODULE,
++	},
++};
++
++static int __init atmel_lcdfb_init(void)
++{
++	return platform_driver_probe(&atmel_lcdfb_driver, atmel_lcdfb_probe);
++}
++
++static void __exit atmel_lcdfb_exit(void)
++{
++	platform_driver_unregister(&atmel_lcdfb_driver);
++}
++
++module_init(atmel_lcdfb_init);
++module_exit(atmel_lcdfb_exit);
++
++MODULE_DESCRIPTION("AT91/AT32 LCD Controller framebuffer driver");
++MODULE_AUTHOR("Nicolas Ferre <nicolas.ferre@rfo.atmel.com>");
++MODULE_LICENSE("GPL");
+diff -urN -x CVS linux-2.6.21/drivers/video/backlight/Kconfig linux-2.6-stable/drivers/video/backlight/Kconfig
+--- linux-2.6.21/drivers/video/backlight/Kconfig	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/video/backlight/Kconfig	Tue May  8 12:13:31 2007
+@@ -63,3 +63,11 @@
+ 	help
+ 	  If you have a Frontpath ProGear say Y to enable the
+ 	  backlight driver.
++
++config BACKLIGHT_KB920x
++	tristate "KwikByte KB9202 Backlight Driver"
++	depends on BACKLIGHT_CLASS_DEVICE && MACH_KB9200
++	default y
++	help
++	  If you have a KwikByte KB9202 board, say Y to enable the
++	  backlight driver.
+diff -urN -x CVS linux-2.6.21/drivers/video/backlight/Makefile linux-2.6-stable/drivers/video/backlight/Makefile
+--- linux-2.6.21/drivers/video/backlight/Makefile	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/drivers/video/backlight/Makefile	Tue May  8 12:13:31 2007
+@@ -6,3 +6,4 @@
+ obj-$(CONFIG_BACKLIGHT_HP680)	+= hp680_bl.o
+ obj-$(CONFIG_BACKLIGHT_LOCOMO)	+= locomolcd.o
+ obj-$(CONFIG_BACKLIGHT_PROGEAR) += progear_bl.o
++obj-$(CONFIG_BACKLIGHT_KB920x)	+= kb920x_bl.o
+diff -urN -x CVS linux-2.6.21/drivers/video/backlight/kb920x_bl.c linux-2.6-stable/drivers/video/backlight/kb920x_bl.c
+--- linux-2.6.21/drivers/video/backlight/kb920x_bl.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/video/backlight/kb920x_bl.c	Tue May  8 12:13:31 2007
+@@ -0,0 +1,164 @@
++/*
++ * Backlight Driver for KB9202
++ *
++ * Copyright (c) 2006 KwikByte
++ *
++ * Based on Sharp's Corgi Backlight Driver
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ */
++
++#include <linux/module.h>
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/spinlock.h>
++#include <linux/fb.h>
++#include <linux/backlight.h>
++
++#include <asm/arch/gpio.h>
++
++/* The backlight is on(1)/off(0) */
++#define	KB9202_DEFAULT_INTENSITY	1
++#define	KB9202_MAX_INTENSITY		1
++
++static int kb9202bl_suspended;
++static int current_intensity = 0;
++static DEFINE_SPINLOCK(bl_lock);
++
++static int kb9202bl_set_intensity(struct backlight_device *bd)
++{
++	unsigned long flags;
++	int intensity = bd->props.brightness;
++
++	if (bd->props.power != FB_BLANK_UNBLANK)
++		intensity = 0;
++	if (bd->props.fb_blank != FB_BLANK_UNBLANK)
++		intensity = 0;
++	if (kb9202bl_suspended)
++		intensity = 0;
++
++	if ((!current_intensity) && (bd->props.power == FB_BLANK_UNBLANK))
++		intensity = 1;
++
++	spin_lock_irqsave(&bl_lock, flags);
++	if (intensity)
++		gpio_set_value(AT91_PIN_PC23, 1);
++	else
++		gpio_set_value(AT91_PIN_PC23, 0);
++	spin_unlock_irqrestore(&bl_lock, flags);
++
++	current_intensity = intensity;
++
++	return 0;
++}
++
++static int kb9202bl_get_intensity(struct backlight_device *bd)
++{
++	return current_intensity;
++}
++
++static struct backlight_ops kb9202bl_ops = {
++	.get_brightness	= kb9202bl_get_intensity,
++	.update_status	= kb9202bl_set_intensity,
++};
++
++static int __init kb9202bl_probe(struct platform_device *pdev)
++{
++	struct backlight_device *bd;
++
++	bd = backlight_device_register ("kb9202-bl", &pdev->dev, NULL, &kb9202bl_ops);
++	if (IS_ERR(bd))
++		return PTR_ERR(bd);
++
++	platform_set_drvdata(pdev, bd);
++
++	bd->props.max_brightness = KB9202_MAX_INTENSITY;
++	bd->props.brightness = KB9202_DEFAULT_INTENSITY;
++	(void) kb9202bl_set_intensity(bd);
++
++	return 0;
++}
++
++static int kb9202bl_remove(struct platform_device *pdev)
++{
++	struct backlight_device *bd = platform_get_drvdata(pdev);
++
++	bd->props.brightness = 0;
++	bd->props.power = 0;
++	(void) kb9202bl_set_intensity(bd);
++
++	backlight_device_unregister(bd);
++
++	return 0;
++}
++
++#ifdef CONFIG_PM
++static int kb9202bl_suspend(struct platform_device *dev, pm_message_t state)
++{
++	struct backlight_device *bd = platform_get_drvdata(pdev);
++
++	kb9202bl_suspended = 1;
++	(void) kb9202bl_set_intensity(bd);
++	return 0;
++}
++
++static int kb9202bl_resume(struct platform_device *dev)
++{
++	struct backlight_device *bd = platform_get_drvdata(pdev);
++
++	kb9202bl_suspended = 0;
++	(void) kb9202bl_set_intensity(bd);
++	return 0;
++}
++#else
++#define kb9202bl_suspend	NULL
++#define kb9202bl_resume		NULL
++#endif
++
++static struct platform_driver kb9202bl_driver = {
++	.probe		= kb9202bl_probe,
++	.remove		= kb9202bl_remove,
++	.suspend	= kb9202bl_suspend,
++	.resume		= kb9202bl_resume,
++	.driver		= {
++		.name	= "kb9202-bl",
++		.owner	= THIS_MODULE,
++	},
++};
++
++static struct platform_device *kb9202bl_device;
++
++static int __init kb9202bl_init(void)
++{
++	int ret;
++
++	ret = platform_driver_register(&kb9202bl_driver);
++	if (!ret) {
++		kb9202bl_device = platform_device_alloc("kb9202-bl", -1);
++		if (!kb9202bl_device)
++			return -ENOMEM;
++
++		ret = platform_device_add(kb9202bl_device);
++		if (ret) {
++			platform_device_put(kb9202bl_device);
++			platform_driver_unregister(&kb9202bl_driver);
++		}
++	}
++	return ret;
++}
++
++static void __exit kb9202bl_exit(void)
++{
++	platform_device_unregister(kb9202bl_device);
++	platform_driver_unregister(&kb9202bl_driver);
++}
++
++module_init(kb9202bl_init);
++module_exit(kb9202bl_exit);
++
++MODULE_AUTHOR("KwikByte <kb9200_dev@kwikbyte.com>");
++MODULE_DESCRIPTION("KB9202 Backlight Driver");
++MODULE_LICENSE("GPL");
+diff -urN -x CVS linux-2.6.21/drivers/video/s1d15605fb.c linux-2.6-stable/drivers/video/s1d15605fb.c
+--- linux-2.6.21/drivers/video/s1d15605fb.c	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/drivers/video/s1d15605fb.c	Tue May  8 12:13:31 2007
+@@ -0,0 +1,659 @@
++/*
++ *  drivers/video/s1d15605.c
++ *
++ * Adapted from several sources including:
++ * 1) Driver for AT91 LCD Controller
++ *    Copyright (C) 2006 Atmel
++ *
++ * 2) Copyright (C) 2005 S. Kevin Hester
++ *
++ *   This file is subject to the terms and conditions of the GNU General Public
++ *   License. See the file COPYING in the main directory of this archive for
++ *   more details.
++ *
++ *   This is a basic framebuffer driver for the Optrex F-51320 128x64 mono LCD
++ *   display.  This display uses a clone of the common Epson SED 1531 display
++ *   controller.
++ *
++ *   I've heavily borrowed code from the vfb.c driver.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++
++#ifdef DEBUG
++#define MSG(string, args...) printk("s1d15605fb:" string, ##args)
++#else
++#define MSG(string, args...)
++#endif
++
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++#include <linux/dma-mapping.h>
++#include <linux/interrupt.h>
++#include <linux/clk.h>
++#include <linux/fb.h>
++#include <linux/init.h>
++#include <linux/delay.h>
++
++#include <asm/uaccess.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++
++#ifdef CONFIG_PMAC_BACKLIGHT
++#include <asm/backlight.h>
++#endif
++
++#define VIDEOWIDTH		128
++#define VIDEOHEIGHT		64
++#define VIDEODEPTH		1	/* bits/pixel */
++#define VIDEOWIDTH_BYTES	((VIDEOWIDTH * VIDEODEPTH) / 8)
++
++/* The number of bytes that actually go to the device */
++#define ACTUALVIDEOMEMSIZE	(VIDEOWIDTH_BYTES * VIDEOHEIGHT)
++#define VIDEOMEMSIZE		PAGE_SIZE
++
++static struct fb_var_screeninfo s1d15605_default __initdata = {
++	.xres		= VIDEOWIDTH,
++	.yres		= VIDEOHEIGHT,
++	.xres_virtual	= VIDEOWIDTH,
++	.yres_virtual	= VIDEOHEIGHT,
++	.bits_per_pixel	= VIDEODEPTH,
++	.red		= { 0, 1, 0 },
++	.green		= { 0, 1, 0 },
++	.blue		= { 0, 1, 0 },
++	.activate	= FB_ACTIVATE_NOW,
++	.pixclock	= 20000,
++	.vmode		= FB_VMODE_NONINTERLACED,
++};
++
++static struct fb_fix_screeninfo s1d15605_fix __initdata = {
++	.id		= "s1d15605",
++	.type		= FB_TYPE_PACKED_PIXELS,
++	.visual		= FB_VISUAL_MONO10,
++	.xpanstep	= 0,
++	.ypanstep	= 0,
++	.ywrapstep	= 0,
++	.accel		= FB_ACCEL_NONE,
++};
++
++struct s1d15605fb_info {
++	struct fb_info		*info;
++	char			*mmio;
++	unsigned long		reset_pin;
++	struct platform_device	*pdev;
++};
++
++/*
++ * LCD device interface
++ */
++#define	RESET_DISPLAY		0xE2
++#define	LCD_BIAS_1_9		0xA2
++#define	ADC_SELECT_REVERSE	0xA1
++#define	COMMON_OUTPUT_NORMAL	0xC0
++#define	V5_RESISTOR_RATIO	0x26
++#define	ELECTRONIC_VOLUME_SET	0x81
++#define	ELECTRONIC_VOLUME_INIT	0x20
++#define	POWER_CONTROL_SET	0x28
++#define	VOLTAGE_REGULATOR	0x02
++#define	VOLTAGE_FOLLOWER	0x01
++#define	BOOSTER_CIRCUIT		0x04
++#define	DISPLAY_ON		0xAF
++#define	START_LINE_SET		0x40
++#define	PAGE_ADDRESS_SET	0xB0
++#define	COLUMN_ADDRESS_HIGH	0x10
++#define	COLUMN_ADDRESS_LOW	0x00
++#define	RESISTOR_RATIO_START	0x20
++
++#define	NUM_OF_PAGES		8
++#define	NUM_OF_COLUMNS		128
++
++#define	WRITE_COMMAND(x)	__raw_writeb((x), (sinfo)->mmio)
++#define	READ_COMMAND		__raw_readb((sinfo)->mmio)
++#define	WRITE_DATA(x)		__raw_writeb((x), (sinfo)->mmio + (0x10000))
++#define	READ_DATA		__raw_readb((sinfo)->mmio + (0x10000))
++
++
++/*
++ *	s1d15605fb_resize_framebuffer
++ *
++ *	Free allocated space if different.  Allocate on new of changed.
++ *	Returns -ENOMEM if the new framebuffer can not be allocated,
++ *	zero on success.
++ */
++static int s1d15605fb_resize_framebuffer(struct s1d15605fb_info *sinfo)
++{
++	struct fb_info			*info = sinfo->info;
++	struct fb_fix_screeninfo	*fix = &info->fix;
++	struct fb_var_screeninfo	*var = &info->var;
++	unsigned int			new_size;
++	void				*new_vaddr;
++
++	new_size = ((var->xres_virtual * var->yres_virtual * var->bits_per_pixel) / 8);
++
++	MSG("%s: x (%d) y (%d) bpp (%d): new size 0x%08x\n", __FUNCTION__,
++		var->xres_virtual, var->yres_virtual, var->bits_per_pixel, new_size);
++
++	if (new_size == fix->smem_len)
++		return 0;
++
++	if (fix->smem_len) {
++		kfree(info->screen_base);
++	}
++
++	new_vaddr = kmalloc(new_size, GFP_KERNEL);
++
++	if (!new_vaddr) {
++		fix->smem_len = 0;
++		return -ENOMEM;
++	}
++
++	info->screen_base = new_vaddr;
++	fix->smem_start = (unsigned)new_vaddr;
++	fix->smem_len = new_size;
++	fix->line_length = (var->xres_virtual * var->bits_per_pixel) / 8;
++
++	dev_info(info->device,
++		"%luKiB frame buffer at %08lx (mapped at %p)\n",
++		(unsigned long)info->fix.smem_len / 1024,
++		(unsigned long)info->fix.smem_start,
++		info->screen_base);
++
++	return 0;
++}
++
++
++/*
++ * The s1d15605 seems to be divided into eight 128 pixel wide pages (from top to
++ * bottom) each page seems to be eight pixels high, where these eight pixels are
++ * one byte
++ */
++static void s1d15605_update(struct fb_info *info)
++{
++	struct s1d15605fb_info	*sinfo = info->par;
++	int			page, i, row, colmask;
++	u8			retVal, *rowPtr;
++
++	WRITE_COMMAND(START_LINE_SET);
++	for (page = 0; page < NUM_OF_PAGES; ++page) {
++		WRITE_COMMAND(PAGE_ADDRESS_SET + page);
++		WRITE_COMMAND(COLUMN_ADDRESS_HIGH);
++		WRITE_COMMAND(COLUMN_ADDRESS_LOW);
++
++		for (i = 0; i < NUM_OF_COLUMNS; ++i)
++		{
++			/* point of opportunity: optimization */
++			colmask = (1 << (i & 0x7));
++			rowPtr = (u8*)(info->screen_base);
++			rowPtr += (VIDEOWIDTH_BYTES * 8 * page);
++			rowPtr += (i >> 3);
++			retVal = 0;
++			for (row = 0; row < 8; ++row)
++			{
++				retVal = (retVal >> 1) | (((*rowPtr) & colmask) ? 0x80 : 0);
++				rowPtr += VIDEOWIDTH_BYTES;
++			}
++			WRITE_DATA(retVal);
++		}
++	}
++
++	WRITE_COMMAND(DISPLAY_ON);
++}
++
++
++/*
++ * Setting the video mode has been split into two parts.
++ * First part, xxxfb_check_var, must not write anything
++ * to hardware, it should only verify and adjust var.
++ * This means it doesn't alter par but it does use hardware
++ * data from it to check this var.
++ */
++static int s1d15605_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
++{
++	/*
++	 * Some very basic checks
++	 */
++	if (!var->xres)
++		var->xres = 1;
++	if (!var->yres)
++		var->yres = 1;
++	if (var->xres > var->xres_virtual)
++		var->xres_virtual = var->xres;
++	if (var->yres > var->yres_virtual)
++		var->yres_virtual = var->yres;
++
++	if(var->bits_per_pixel > VIDEODEPTH)
++		return -EINVAL;
++
++	/*
++	 * Memory limit
++	 */
++	if (((var->yres_virtual * var->bits_per_pixel * var->yres_virtual) >> 3) >
++			ACTUALVIDEOMEMSIZE)
++		return -ENOMEM;
++
++	/*
++	 * Now that we checked it we alter var. The reason being is that the video
++	 * mode passed in might not work but slight changes to it might make it
++	 * work. This way we let the user know what is acceptable.
++	 */
++	switch (var->bits_per_pixel) {
++	case 1:
++		var->red.offset = var->green.offset = var->blue.offset = 0;
++		var->red.length = var->green.length = var->blue.length
++			= var->bits_per_pixel;
++		break;
++	default:
++		return -EINVAL;
++	}
++
++	var->xoffset = var->yoffset = 0;
++	var->red.msb_right = var->green.msb_right = var->blue.msb_right =
++		var->transp.msb_right = 0;
++
++	return 0;
++}
++
++
++/*
++ * This routine actually sets the video mode. It's in here where we
++ * the hardware state info->par and fix which can be affected by the
++ * change in par. For this driver it doesn't do much.
++ */
++static int s1d15605_set_par(struct fb_info *info)
++{
++	int	ret;
++
++	MSG("%s:\n", __func__);
++	MSG("  * resolution: %ux%u (%ux%u virtual)\n",
++		 info->var.xres, info->var.yres,
++		 info->var.xres_virtual, info->var.yres_virtual);
++
++	ret = s1d15605fb_resize_framebuffer(info->par);
++
++	info->fix.visual = FB_VISUAL_MONO10;
++	return ret;
++}
++
++
++/*
++ * Set a single color register. The values supplied are already
++ * rounded down to the hardware's capabilities (according to the
++ * entries in the var structure). Return != 0 for invalid regno.
++ */
++static int s1d15605_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
++			u_int transp, struct fb_info *info)
++{
++	if (regno > 1)	/* no. of hw registers - we only do mono now */
++		return 1;
++
++	return 0;
++}
++
++
++/*
++ * Currently, the routine will simply shut-off the backlight and prevent
++ * updates/refreshes.  Modify according to application.
++ *
++ * 0 unblank, 1 blank, 2 no vsync, 3 no hsync, 4 off
++ */
++static int s1d15605_blank(int blank, struct fb_info *info)
++{
++#ifdef CONFIG_PMAC_BACKLIGHT
++	if (blank)
++		pmac_backlight->props.power = FB_BLANK_POWERDOWN;
++	else
++		pmac_backlight->props.power = FB_BLANK_UNBLANK;
++	backlight_update_status(pmac_backlight);
++#endif
++	return 1;
++}
++
++
++/*
++ * Pan or Wrap the Display
++ *
++ * This call looks only at xoffset, yoffset and the FB_VMODE_YWRAP flag
++ */
++/*
++static int s1d15605_pan_display(struct fb_var_screeninfo *var,
++			struct fb_info *info)
++{
++	if (var->vmode & FB_VMODE_YWRAP) {
++		if (var->yoffset < 0
++		    || var->yoffset >= info->var.yres_virtual
++		    || var->xoffset)
++			return -EINVAL;
++	} else {
++		if (var->xoffset + var->xres > info->var.xres_virtual ||
++		    var->yoffset + var->yres > info->var.yres_virtual)
++			return -EINVAL;
++	}
++	info->var.xoffset = var->xoffset;
++	info->var.yoffset = var->yoffset;
++	if (var->vmode & FB_VMODE_YWRAP)
++		info->var.vmode |= FB_VMODE_YWRAP;
++	else
++		info->var.vmode &= ~FB_VMODE_YWRAP;
++	return 0;
++}
++*/
++
++
++static void s1d15605_copyarea(struct fb_info *info, const struct fb_copyarea *region)
++{
++	cfb_copyarea(info, region);
++	s1d15605_update(info);
++}
++
++
++static void s1d15605_fillrect (struct fb_info *info, const struct fb_fillrect *rect)
++{
++	cfb_fillrect(info, rect);
++	s1d15605_update(info);
++}
++
++
++static void s1d15605_imageblit(struct fb_info *p, const struct fb_image *image)
++{
++	cfb_imageblit(p, image);
++	s1d15605_update(p);
++}
++
++
++/*
++ * Write the users data to our framebuffer, and then trigger a psuedo DMA
++ */
++static ssize_t s1d15605_write(struct file *file, const char *buf,
++			size_t count, loff_t *ppos)
++{
++	unsigned long p = *ppos;
++	struct inode *inode = file->f_dentry->d_inode;
++	int fbidx = iminor(inode);
++	struct fb_info *info = registered_fb[fbidx];
++	int err;
++
++	if (p > info->fix.smem_len)
++		return -ENOSPC;
++	if (count >= info->fix.smem_len)
++		count = info->fix.smem_len;
++	err = 0;
++	if (count + p > info->fix.smem_len) {
++		count = info->fix.smem_len - p;
++		err = -ENOSPC;
++	}
++	if (count) {
++		char *base_addr;
++
++		base_addr = info->screen_base;
++		count -= copy_from_user(base_addr+p, buf, count);
++		*ppos += count;
++		err = -EFAULT;
++	}
++
++	s1d15605_update(info);
++
++	if (count)
++		return count;
++
++	return err;
++}
++
++#ifdef	USE_PRIVATE_VMA_FXS
++static void s1d15605_vma_open(struct vm_area_struct *vma)
++{
++	// FIXME - store stats in the device data via vm_private_data
++}
++
++
++static void s1d15605_vma_close(struct vm_area_struct *vma)
++{
++	// FIXME - store stats in the device data via vm_private_data
++}
++
++
++static struct page *s1d15605_vma_nopage(struct vm_area_struct *vma,
++				unsigned long address, int *type)
++{
++	struct page *page;
++	struct fb_info *info = vma->vm_private_data;
++
++	page = virt_to_page(info->screen_base);
++	get_page(page);
++
++	// FIXME - now someone has a link to our page, start periodically blitting
++	// latest updates to the actual device.
++
++	return page;
++}
++
++
++static struct vm_operations_struct s1d15605_vm_ops = {
++	.open	= s1d15605_vma_open,
++	.close	= s1d15605_vma_close,
++	.nopage	= s1d15605_vma_nopage
++};
++
++
++/* We don't do much here - because we have special vm_ops */
++static int s1d15605_mmap(struct fb_info *info, struct vm_area_struct *vma)
++{
++	vma->vm_ops = &s1d15605_vm_ops;
++	vma->vm_flags |= VM_RESERVED;
++	vma->vm_private_data = info;
++	s1d15605_vma_open(vma);
++
++	return 0;
++}
++#endif /* USE_PRIVATE_VMA_FXS */
++
++
++static struct fb_ops s1d15605fb_ops = {
++	.owner		= THIS_MODULE,
++	.fb_check_var	= s1d15605_check_var,
++	.fb_set_par	= s1d15605_set_par,
++	.fb_setcolreg	= s1d15605_setcolreg,
++	.fb_blank	= s1d15605_blank,
++//	.fb_pan_display	= s1d15605_pan_display,
++	.fb_fillrect	= s1d15605_fillrect,
++	.fb_copyarea	= s1d15605_copyarea,
++	.fb_imageblit	= s1d15605_imageblit,
++	.fb_write	= s1d15605_write,
++#ifdef	USE_PRIVATE_VMA_FXS
++	.fb_mmap	= s1d15605_mmap,
++#endif
++};
++
++
++static void s1d15605_device_init(struct s1d15605fb_info *sinfo) {
++
++	char	value;
++
++	/* release the reset line by reading the device - proto hardware */
++	value = READ_COMMAND;
++	value = READ_COMMAND;
++
++#ifdef CONFIG_MACH_KB9200
++	/* new boards have dedicated reset line */
++	gpio_set_value(sinfo->reset_pin, 1);
++#endif
++
++	/* initialize the device within 5ms */
++	WRITE_COMMAND(RESET_DISPLAY);
++	WRITE_COMMAND(LCD_BIAS_1_9);
++	WRITE_COMMAND(ADC_SELECT_REVERSE);
++	WRITE_COMMAND(COMMON_OUTPUT_NORMAL);
++	WRITE_COMMAND(V5_RESISTOR_RATIO);
++	WRITE_COMMAND(ELECTRONIC_VOLUME_SET);
++	WRITE_COMMAND(ELECTRONIC_VOLUME_INIT);
++	WRITE_COMMAND(POWER_CONTROL_SET | VOLTAGE_REGULATOR | VOLTAGE_FOLLOWER | BOOSTER_CIRCUIT);
++	WRITE_COMMAND(DISPLAY_ON);
++
++	WRITE_COMMAND(RESISTOR_RATIO_START + 4);
++	WRITE_COMMAND(ELECTRONIC_VOLUME_SET);
++	WRITE_COMMAND(0x33);
++}
++
++
++static int s1d15605fb_probe(struct platform_device *pdev)
++{
++	struct device *dev = &pdev->dev;
++	struct fb_info *info;
++	struct s1d15605fb_info *sinfo;
++	int ret;
++
++	MSG("%s\n", __func__);
++
++	if (!(info = framebuffer_alloc(sizeof(struct s1d15605fb_info), dev))) {
++		dev_err(dev, "Cannot allocate framebuffer struct\n");
++		return -ENOMEM;
++	}
++
++	sinfo = info->par;
++	sinfo->info = info;
++	sinfo->pdev = pdev;
++
++	if (pdev->num_resources < 2) {
++		dev_err(dev, "Resources unusable\n");
++		ret = -ENODEV;
++		goto free_info;
++	}
++
++	info->fbops = &s1d15605fb_ops;
++	strcpy(info->fix.id, pdev->name);
++
++	info->fix.mmio_start = pdev->resource[0].start;
++	info->fix.mmio_len = pdev->resource[0].end - pdev->resource[0].start + 1;
++	sinfo->reset_pin = pdev->resource[1].start;
++
++	ret = s1d15605fb_resize_framebuffer(sinfo);
++	if (ret < 0) {
++		dev_err(dev, "Cannot resize framebuffer: %d\n", ret);
++		goto free_fb;
++	}
++
++	if (!request_mem_region(info->fix.mmio_start,
++				info->fix.mmio_len, pdev->name)) {
++		ret = -EBUSY;
++		goto free_fb;
++	}
++
++	sinfo->mmio = ioremap(info->fix.mmio_start, info->fix.mmio_len);
++	if (!sinfo->mmio) {
++		dev_err(dev, "Cannot map LCD memory region\n");
++		goto release_mem;
++	}
++
++	s1d15605_device_init(sinfo);
++
++	ret = fb_find_mode(&info->var, info, NULL, NULL, 0, NULL, 1);
++
++	if (!ret || (ret == 4))
++		info->var = s1d15605_default;
++
++	info->fix = s1d15605_fix;
++	info->flags = FBINFO_FLAG_DEFAULT |
++/*		FBINFO_HWACCEL_YPAN | */
++		FBINFO_HWACCEL_FILLRECT | FBINFO_HWACCEL_COPYAREA;
++
++	ret = register_framebuffer(info);
++	if (ret < 0) {
++		dev_err(dev, "Failed to register framebuffer device: %d\n", ret);
++		goto unmap_mmio;
++	}
++
++	dev_set_drvdata(dev, info);
++
++	memset(info->screen_base, 0, info->fix.smem_len);
++	info->var.activate |= FB_ACTIVATE_NOW;
++	ret = fb_set_var(info, &info->var);
++	if (ret) {
++		dev_warn(dev, "Unable to set display parameters\n");
++	}
++
++	info->var.activate &= ~(FB_ACTIVATE_FORCE | FB_ACTIVATE_NOW);
++
++	dev_dbg(dev, "%s SUCCESS\n", __func__);
++
++	dev_info(dev, "Driver $Revision: 1.1 $\n");
++
++	return 0;
++
++unmap_mmio:
++	iounmap(sinfo->mmio);
++release_mem:
++	release_mem_region(info->fix.mmio_start, info->fix.mmio_len);
++free_fb:
++	kfree(info->screen_base);
++
++free_info:
++	framebuffer_release(info);
++
++	dev_dbg(dev, "%s FAILED\n", __func__);
++	return ret;
++}
++
++
++static int s1d15605fb_remove(struct platform_device *pdev)
++{
++	struct device *dev = &pdev->dev;
++	struct fb_info *info = dev_get_drvdata(dev);
++	struct s1d15605fb_info *sinfo = info->par;
++
++	if (!sinfo)
++		return 0;
++
++	unregister_framebuffer(info);
++
++	iounmap(sinfo->mmio);
++	release_mem_region(info->fix.mmio_start, info->fix.mmio_len);
++
++	kfree(info->screen_base);
++
++	dev_set_drvdata(dev, NULL);
++	framebuffer_release(info);
++	return 0;
++}
++
++
++static struct platform_driver s1d15605fb_driver = {
++	.probe		= s1d15605fb_probe,
++	.remove		= s1d15605fb_remove,
++	.driver		= {
++		.name	= "s1d15605fb",
++		.owner	= THIS_MODULE,
++	},
++};
++
++
++static int __init s1d15605fb_init(void)
++{
++	return platform_driver_register(&s1d15605fb_driver);
++}
++
++
++static void __exit s1d15605fb_exit(void)
++{
++	platform_driver_unregister(&s1d15605fb_driver);
++}
++
++
++module_init(s1d15605fb_init);
++module_exit(s1d15605fb_exit);
++
++
++MODULE_AUTHOR("KwikByte");
++MODULE_DESCRIPTION("Epson S1D15605 LCD Controller framebuffer driver");
++MODULE_LICENSE("GPL");
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91_adc.h linux-2.6-stable/include/asm-arm/arch-at91/at91_adc.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91_adc.h	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91_adc.h	Tue May  8 12:13:31 2007
+@@ -0,0 +1,61 @@
++/*
++ * include/asm-arm/arch-at91/at91_adc.h
++ *
++ * Copyright (C) SAN People
++ *
++ * Analog-to-Digital Converter (ADC) registers.
++ * Based on AT91SAM9260 datasheet revision D.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ */
++
++#ifndef AT91_ADC_H
++#define AT91_ADC_H
++
++#define AT91_ADC_CR		0x00		/* Control Register */
++#define		AT91_ADC_SWRST		(1 << 0)	/* Software Reset */
++#define		AT91_ADC_START		(1 << 1)	/* Start Conversion */
++
++#define AT91_ADC_MR		0x04		/* Mode Register */
++#define		AT91_ADC_TRGEN		(1 << 0)	/* Trigger Enable */
++#define		AT91_ADC_TRGSEL		(7 << 1)	/* Trigger Selection */
++#define			AT91_ADC_TRGSEL_TC0		(0 << 1)
++#define			AT91_ADC_TRGSEL_TC1		(1 << 1)
++#define			AT91_ADC_TRGSEL_TC2		(2 << 1)
++#define			AT91_ADC_TRGSEL_EXTERNAL	(6 << 1)
++#define		AT91_ADC_LOWRES		(1 << 4)	/* Low Resolution */
++#define		AT91_ADC_SLEEP		(1 << 5)	/* Sleep Mode */
++#define		AT91_ADC_PRESCAL	(0x3f << 8)	/* Prescalar Rate Selection */
++#define			AT91_ADC_PRESCAL_(x)	((x) << 8)
++#define		AT91_ADC_STARTUP	(0x1f << 16)	/* Startup Up Time */
++#define			AT91_ADC_STARTUP_(x)	((x) << 16)
++#define		AT91_ADC_SHTIM		(0xf  << 24)	/* Sample & Hold Time */
++#define			AT91_ADC_SHTIM_(x)	((x) << 24)
++
++#define AT91_ADC_CHER		0x10		/* Channel Enable Register */
++#define AT91_ADC_CHDR		0x14		/* Channel Disable Register */
++#define AT91_ADC_CHSR		0x18		/* Channel Status Register */
++#define		AT91_ADC_CH(n)		(1 << (n))	/* Channel Number */
++
++#define AT91_ADC_SR		0x1C		/* Status Register */
++#define		AT91_ADC_EOC(n)		(1 << (n))	/* End of Conversion on Channel N */
++#define		AT91_ADC_OVRE(n)	(1 << ((n) + 8))/* Overrun Error on Channel N */
++#define		AT91_ADC_DRDY		(1 << 16)	/* Data Ready */
++#define		AT91_ADC_GOVRE		(1 << 17)	/* General Overrun Error */
++#define		AT91_ADC_ENDRX		(1 << 18)	/* End of RX Buffer */
++#define		AT91_ADC_RXFUFF		(1 << 19)	/* RX Buffer Full */
++
++#define AT91_ADC_LCDR		0x20		/* Last Converted Data Register */
++#define		AT91_ADC_LDATA		(0x3ff)
++
++#define AT91_ADC_IER		0x24		/* Interrupt Enable Register */
++#define AT91_ADC_IDR		0x28		/* Interrupt Disable Register */
++#define AT91_ADC_IMR		0x2C		/* Interrupt Mask Register */
++
++#define AT91_ADC_CHR(n)		(0x30 + ((n) * 4)	/* Channel Data Register N */
++#define		AT91_ADC_DATA		(0x3ff)
++
++#endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91_mci.h linux-2.6-stable/include/asm-arm/arch-at91/at91_mci.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91_mci.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91_mci.h	Tue May  8 12:13:31 2007
+@@ -26,6 +26,9 @@
+ #define AT91_MCI_MR		0x04		/* Mode Register */
+ #define		AT91_MCI_CLKDIV		(0xff  <<  0)	/* Clock Divider */
+ #define		AT91_MCI_PWSDIV		(7     <<  8)	/* Power Saving Divider */
++#define		AT91_MCI_RDPROOF	(1     << 11)	/* Read Proof Enable [SAM926[03] only] */
++#define		AT91_MCI_WRPROOF	(1     << 12)	/* Write Proof Enable [SAM926[03] only] */
++#define		AT91_MCI_PDCFBYTE	(1     << 13)	/* PDC Force Byte Transfer [SAM926[03] only] */
+ #define		AT91_MCI_PDCPADV	(1     << 14)	/* PDC Padding Value */
+ #define		AT91_MCI_PDCMODE	(1     << 15)	/* PDC-orientated Mode */
+ #define		AT91_MCI_BLKLEN		(0xfff << 18)	/* Data Block Length */
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91_pmc.h linux-2.6-stable/include/asm-arm/arch-at91/at91_pmc.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91_pmc.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91_pmc.h	Fri May 11 16:45:00 2007
+@@ -37,7 +37,9 @@
+ #define	AT91_PMC_PCDR		(AT91_PMC + 0x14)	/* Peripheral Clock Disable Register */
+ #define	AT91_PMC_PCSR		(AT91_PMC + 0x18)	/* Peripheral Clock Status Register */
+ 
+-#define	AT91_CKGR_MOR		(AT91_PMC + 0x20)	/* Main Oscillator Register */
++#define AT91_CKGR_UCKR		(AT91_PMC + 0x1C)	/* UTMI Clock Register [SAM9RL only] */
++
++#define	AT91_CKGR_MOR		(AT91_PMC + 0x20)	/* Main Oscillator Register [not on SAM9RL] */
+ #define		AT91_PMC_MOSCEN		(1    << 0)		/* Main Oscillator Enable */
+ #define		AT91_PMC_OSCBYPASS	(1    << 1)		/* Oscillator Bypass [AT91SAM926x only] */
+ #define		AT91_PMC_OSCOUNT	(0xff << 8)		/* Main Oscillator Start-up Time */
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91rm9200.h linux-2.6-stable/include/asm-arm/arch-at91/at91rm9200.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91rm9200.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91rm9200.h	Tue May  8 12:56:33 2007
+@@ -107,185 +107,4 @@
+ #define AT91RM9200_UHP_BASE	0x00300000	/* USB Host controller */
+ 
+ 
+-#if 0
+-/*
+- * PIO pin definitions (peripheral A/B multiplexing).
+- */
+-#define AT91_PA0_MISO		(1 <<  0)	/* A: SPI Master-In Slave-Out */
+-#define AT91_PA0_PCK3		(1 <<  0)	/* B: PMC Programmable Clock Output 3 */
+-#define AT91_PA1_MOSI		(1 <<  1)	/* A: SPI Master-Out Slave-In */
+-#define AT91_PA1_PCK0		(1 <<  1)	/* B: PMC Programmable Clock Output 0 */
+-#define AT91_PA2_SPCK		(1 <<  2)	/* A: SPI Serial Clock */
+-#define AT91_PA2_IRQ4		(1 <<  2)	/* B: External Interrupt 4 */
+-#define AT91_PA3_NPCS0		(1 <<  3)	/* A: SPI Peripheral Chip Select 0 */
+-#define AT91_PA3_IRQ5		(1 <<  3)	/* B: External Interrupt 5 */
+-#define AT91_PA4_NPCS1		(1 <<  4)	/* A: SPI Peripheral Chip Select 1 */
+-#define AT91_PA4_PCK1		(1 <<  4)	/* B: PMC Programmable Clock Output 1 */
+-#define AT91_PA5_NPCS2		(1 <<  5)	/* A: SPI Peripheral Chip Select 2 */
+-#define AT91_PA5_TXD3		(1 <<  5)	/* B: USART Transmit Data 3 */
+-#define AT91_PA6_NPCS3		(1 <<  6)	/* A: SPI Peripheral Chip Select 3 */
+-#define AT91_PA6_RXD3		(1 <<  6)	/* B: USART Receive Data 3 */
+-#define AT91_PA7_ETXCK_EREFCK	(1 <<  7)	/* A: Ethernet Reference Clock / Transmit Clock */
+-#define AT91_PA7_PCK2		(1 <<  7)	/* B: PMC Programmable Clock Output 2 */
+-#define AT91_PA8_ETXEN		(1 <<  8)	/* A: Ethernet Transmit Enable */
+-#define AT91_PA8_MCCDB		(1 <<  8)	/* B: MMC Multimedia Card B Command */
+-#define AT91_PA9_ETX0		(1 <<  9)	/* A: Ethernet Transmit Data 0 */
+-#define AT91_PA9_MCDB0		(1 <<  9)	/* B: MMC Multimedia Card B Data 0 */
+-#define AT91_PA10_ETX1		(1 << 10)	/* A: Ethernet Transmit Data 1 */
+-#define AT91_PA10_MCDB1		(1 << 10)	/* B: MMC Multimedia Card B Data 1 */
+-#define AT91_PA11_ECRS_ECRSDV	(1 << 11)	/* A: Ethernet Carrier Sense / Data Valid */
+-#define AT91_PA11_MCDB2		(1 << 11)	/* B: MMC Multimedia Card B Data 2 */
+-#define AT91_PA12_ERX0		(1 << 12)	/* A: Ethernet Receive Data 0 */
+-#define AT91_PA12_MCDB3		(1 << 12)	/* B: MMC Multimedia Card B Data 3 */
+-#define AT91_PA13_ERX1		(1 << 13)	/* A: Ethernet Receive Data 1 */
+-#define AT91_PA13_TCLK0		(1 << 13)	/* B: TC External Clock Input 0 */
+-#define AT91_PA14_ERXER		(1 << 14)	/* A: Ethernet Receive Error */
+-#define AT91_PA14_TCLK1		(1 << 14)	/* B: TC External Clock Input 1 */
+-#define AT91_PA15_EMDC		(1 << 15)	/* A: Ethernet Management Data Clock */
+-#define AT91_PA15_TCLK2		(1 << 15)	/* B: TC External Clock Input 2 */
+-#define AT91_PA16_EMDIO		(1 << 16)	/* A: Ethernet Management Data I/O */
+-#define AT91_PA16_IRQ6		(1 << 16)	/* B: External Interrupt 6 */
+-#define AT91_PA17_TXD0		(1 << 17)	/* A: USART Transmit Data 0 */
+-#define AT91_PA17_TIOA0		(1 << 17)	/* B: TC I/O Line A 0 */
+-#define AT91_PA18_RXD0		(1 << 18)	/* A: USART Receive Data 0 */
+-#define AT91_PA18_TIOB0		(1 << 18)	/* B: TC I/O Line B 0 */
+-#define AT91_PA19_SCK0		(1 << 19)	/* A: USART Serial Clock 0 */
+-#define AT91_PA19_TIOA1		(1 << 19)	/* B: TC I/O Line A 1 */
+-#define AT91_PA20_CTS0		(1 << 20)	/* A: USART Clear To Send 0 */
+-#define AT91_PA20_TIOB1		(1 << 20)	/* B: TC I/O Line B 1 */
+-#define AT91_PA21_RTS0		(1 << 21)	/* A: USART Ready To Send 0 */
+-#define AT91_PA21_TIOA2		(1 << 21)	/* B: TC I/O Line A 2 */
+-#define AT91_PA22_RXD2		(1 << 22)	/* A: USART Receive Data 2 */
+-#define AT91_PA22_TIOB2		(1 << 22)	/* B: TC I/O Line B 2 */
+-#define AT91_PA23_TXD2		(1 << 23)	/* A: USART Transmit Data 2 */
+-#define AT91_PA23_IRQ3		(1 << 23)	/* B: External Interrupt 3 */
+-#define AT91_PA24_SCK2		(1 << 24)	/* A: USART Serial Clock 2 */
+-#define AT91_PA24_PCK1		(1 << 24)	/* B: PMC Programmable Clock Output 1 */
+-#define AT91_PA25_TWD		(1 << 25)	/* A: TWI Two-wire Serial Data */
+-#define AT91_PA25_IRQ2		(1 << 25)	/* B: External Interrupt 2 */
+-#define AT91_PA26_TWCK		(1 << 26)	/* A: TWI Two-wire Serial Clock */
+-#define AT91_PA26_IRQ1		(1 << 26)	/* B: External Interrupt 1 */
+-#define AT91_PA27_MCCK		(1 << 27)	/* A: MMC Multimedia Card Clock */
+-#define AT91_PA27_TCLK3		(1 << 27)	/* B: TC External Clock Input 3 */
+-#define AT91_PA28_MCCDA		(1 << 28)	/* A: MMC Multimedia Card A Command */
+-#define AT91_PA28_TCLK4		(1 << 28)	/* B: TC External Clock Input 4 */
+-#define AT91_PA29_MCDA0		(1 << 29)	/* A: MMC Multimedia Card A Data 0 */
+-#define AT91_PA29_TCLK5		(1 << 29)	/* B: TC External Clock Input 5 */
+-#define AT91_PA30_DRXD		(1 << 30)	/* A: DBGU Receive Data */
+-#define AT91_PA30_CTS2		(1 << 30)	/* B: USART Clear To Send 2 */
+-#define AT91_PA31_DTXD		(1 << 31)	/* A: DBGU Transmit Data */
+-#define AT91_PA31_RTS2		(1 << 31)	/* B: USART Ready To Send 2 */
+-
+-#define AT91_PB0_TF0		(1 <<  0)	/* A: SSC Transmit Frame Sync 0 */
+-#define AT91_PB0_RTS3		(1 <<  0)	/* B: USART Ready To Send 3 */
+-#define AT91_PB1_TK0		(1 <<  1)	/* A: SSC Transmit Clock 0 */
+-#define AT91_PB1_CTS3		(1 <<  1)	/* B: USART Clear To Send 3 */
+-#define AT91_PB2_TD0		(1 <<  2)	/* A: SSC Transmit Data 0 */
+-#define AT91_PB2_SCK3		(1 <<  2)	/* B: USART Serial Clock 3 */
+-#define AT91_PB3_RD0		(1 <<  3)	/* A: SSC Receive Data 0 */
+-#define AT91_PB3_MCDA1		(1 <<  3)	/* B: MMC Multimedia Card A Data 1 */
+-#define AT91_PB4_RK0		(1 <<  4)	/* A: SSC Receive Clock 0 */
+-#define AT91_PB4_MCDA2		(1 <<  4)	/* B: MMC Multimedia Card A Data 2 */
+-#define AT91_PB5_RF0		(1 <<  5)	/* A: SSC Receive Frame Sync 0 */
+-#define AT91_PB5_MCDA3		(1 <<  5)	/* B: MMC Multimedia Card A Data 3 */
+-#define AT91_PB6_TF1		(1 <<  6)	/* A: SSC Transmit Frame Sync 1 */
+-#define AT91_PB6_TIOA3		(1 <<  6)	/* B: TC I/O Line A 3 */
+-#define AT91_PB7_TK1		(1 <<  7)	/* A: SSC Transmit Clock 1 */
+-#define AT91_PB7_TIOB3		(1 <<  7)	/* B: TC I/O Line B 3 */
+-#define AT91_PB8_TD1		(1 <<  8)	/* A: SSC Transmit Data 1 */
+-#define AT91_PB8_TIOA4		(1 <<  8)	/* B: TC I/O Line A 4 */
+-#define AT91_PB9_RD1		(1 <<  9)	/* A: SSC Receive Data 1 */
+-#define AT91_PB9_TIOB4		(1 <<  9)	/* B: TC I/O Line B 4 */
+-#define AT91_PB10_RK1		(1 << 10)	/* A: SSC Receive Clock 1 */
+-#define AT91_PB10_TIOA5		(1 << 10)	/* B: TC I/O Line A 5 */
+-#define AT91_PB11_RF1		(1 << 11)	/* A: SSC Receive Frame Sync 1 */
+-#define AT91_PB11_TIOB5		(1 << 11)	/* B: TC I/O Line B 5 */
+-#define AT91_PB12_TF2		(1 << 12)	/* A: SSC Transmit Frame Sync 2 */
+-#define AT91_PB12_ETX2		(1 << 12)	/* B: Ethernet Transmit Data 2 */
+-#define AT91_PB13_TK2		(1 << 13)	/* A: SSC Transmit Clock 3 */
+-#define AT91_PB13_ETX3		(1 << 13)	/* B: Ethernet Transmit Data 3 */
+-#define AT91_PB14_TD2		(1 << 14)	/* A: SSC Transmit Data 2 */
+-#define AT91_PB14_ETXER		(1 << 14)	/* B: Ethernet Transmit Coding Error */
+-#define AT91_PB15_RD2		(1 << 15)	/* A: SSC Receive Data 2 */
+-#define AT91_PB15_ERX2		(1 << 15)	/* B: Ethernet Receive Data 2 */
+-#define AT91_PB16_RK2		(1 << 16)	/* A: SSC Receive Clock 2 */
+-#define AT91_PB16_ERX3		(1 << 16)	/* B: Ethernet Receive Data 3 */
+-#define AT91_PB17_RF2		(1 << 17)	/* A: SSC Receive Frame Sync 2 */
+-#define AT91_PB17_ERXDV		(1 << 17)	/* B: Ethernet Receive Data Valid */
+-#define AT91_PB18_RI1		(1 << 18)	/* A: USART Ring Indicator 1 */
+-#define AT91_PB18_ECOL		(1 << 18)	/* B: Ethernet Collision Detected */
+-#define AT91_PB19_DTR1		(1 << 19)	/* A: USART Data Terminal Ready 1 */
+-#define AT91_PB19_ERXCK		(1 << 19)	/* B: Ethernet Receive Clock */
+-#define AT91_PB20_TXD1		(1 << 20)	/* A: USART Transmit Data 1 */
+-#define AT91_PB21_RXD1		(1 << 21)	/* A: USART Receive Data 1 */
+-#define AT91_PB22_SCK1		(1 << 22)	/* A: USART Serial Clock 1 */
+-#define AT91_PB23_DCD1		(1 << 23)	/* A: USART Data Carrier Detect 1 */
+-#define AT91_PB24_CTS1		(1 << 24)	/* A: USART Clear To Send 1 */
+-#define AT91_PB25_DSR1		(1 << 25)	/* A: USART Data Set Ready 1 */
+-#define AT91_PB25_EF100		(1 << 25)	/* B: Ethernet Force 100 Mbit */
+-#define AT91_PB26_RTS1		(1 << 26)	/* A: USART Ready To Send 1 */
+-#define AT91_PB27_PCK0		(1 << 27)	/* B: PMC Programmable Clock Output 0 */
+-#define AT91_PB28_FIQ		(1 << 28)	/* A: Fast Interrupt */
+-#define AT91_PB29_IRQ0		(1 << 29)	/* A: External Interrupt 0 */
+-
+-#define AT91_PC0_BFCK		(1 <<  0)	/* A: Burst Flash Clock */
+-#define AT91_PC1_BFRDY_SMOE	(1 <<  1)	/* A: Burst Flash Ready / SmartMedia Output Enable */
+-#define AT91_PC2_BFAVD		(1 <<  2)	/* A: Burst Flash Address Valid */
+-#define AT91_PC3_BFBAA_SMWE	(1 <<  3)	/* A: Burst Flash Address Advance / SmartMedia Write Enable */
+-#define AT91_PC4_BFOE		(1 <<  4)	/* A: Burst Flash Output Enable */
+-#define AT91_PC5_BFWE		(1 <<  5)	/* A: Burst Flash Write Enable */
+-#define AT91_PC6_NWAIT		(1 <<  6)	/* A: SMC Wait Signal */
+-#define AT91_PC7_A23		(1 <<  7)	/* A: Address Bus 23 */
+-#define AT91_PC8_A24		(1 <<  8)	/* A: Address Bus 24 */
+-#define AT91_PC9_A25_CFRNW	(1 <<  9)	/* A: Address Bus 25 / Compact Flash Read Not Write */
+-#define AT91_PC10_NCS4_CFCS	(1 << 10)	/* A: SMC Chip Select 4 / Compact Flash Chip Select */
+-#define AT91_PC11_NCS5_CFCE1	(1 << 11)	/* A: SMC Chip Select 5 / Compact Flash Chip Enable 1 */
+-#define AT91_PC12_NCS6_CFCE2	(1 << 12)	/* A: SMC Chip Select 6 / Compact Flash Chip Enable 2 */
+-#define AT91_PC13_NCS7		(1 << 13)	/* A: Chip Select 7 */
+-
+-#define AT91_PD0_ETX0		(1 <<  0)	/* A: Ethernet Transmit Data 0 */
+-#define AT91_PD1_ETX1		(1 <<  1)	/* A: Ethernet Transmit Data 1 */
+-#define AT91_PD2_ETX2		(1 <<  2)	/* A: Ethernet Transmit Data 2 */
+-#define AT91_PD3_ETX3		(1 <<  3)	/* A: Ethernet Transmit Data 3 */
+-#define AT91_PD4_ETXEN		(1 <<  4)	/* A: Ethernet Transmit Enable */
+-#define AT91_PD5_ETXER		(1 <<  5)	/* A: Ethernet Transmit Coding Error */
+-#define AT91_PD6_DTXD		(1 <<  6)	/* A: DBGU Transmit Data */
+-#define AT91_PD7_PCK0		(1 <<  7)	/* A: PMC Programmable Clock Output 0 */
+-#define AT91_PD7_TSYNC		(1 <<  7)	/* B: ETM Trace Synchronization Signal */
+-#define AT91_PD8_PCK1		(1 <<  8)	/* A: PMC Programmable Clock Output 1 */
+-#define AT91_PD8_TCLK		(1 <<  8)	/* B: ETM Trace Clock */
+-#define AT91_PD9_PCK2		(1 <<  9)	/* A: PMC Programmable Clock Output 2 */
+-#define AT91_PD9_TPS0		(1 <<  9)	/* B: ETM Trace ARM Pipeline Status 0 */
+-#define AT91_PD10_PCK3		(1 << 10)	/* A: PMC Programmable Clock Output 3 */
+-#define AT91_PD10_TPS1		(1 << 10)	/* B: ETM Trace ARM Pipeline Status 1 */
+-#define AT91_PD11_TPS2		(1 << 11)	/* B: ETM Trace ARM Pipeline Status 2 */
+-#define AT91_PD12_TPK0		(1 << 12)	/* B: ETM Trace Packet Port 0 */
+-#define AT91_PD13_TPK1		(1 << 13)	/* B: ETM Trace Packet Port 1 */
+-#define AT91_PD14_TPK2		(1 << 14)	/* B: ETM Trace Packet Port 2 */
+-#define AT91_PD15_TD0		(1 << 15)	/* A: SSC Transmit Data 0 */
+-#define AT91_PD15_TPK3		(1 << 15)	/* B: ETM Trace Packet Port 3 */
+-#define AT91_PD16_TD1		(1 << 16)	/* A: SSC Transmit Data 1 */
+-#define AT91_PD16_TPK4		(1 << 16)	/* B: ETM Trace Packet Port 4 */
+-#define AT91_PD17_TD2		(1 << 17)	/* A: SSC Transmit Data 2 */
+-#define AT91_PD17_TPK5		(1 << 17)	/* B: ETM Trace Packet Port 5 */
+-#define AT91_PD18_NPCS1		(1 << 18)	/* A: SPI Peripheral Chip Select 1 */
+-#define AT91_PD18_TPK6		(1 << 18)	/* B: ETM Trace Packet Port 6 */
+-#define AT91_PD19_NPCS2		(1 << 19)	/* A: SPI Peripheral Chip Select 2 */
+-#define AT91_PD19_TPK7		(1 << 19)	/* B: ETM Trace Packet Port 7 */
+-#define AT91_PD20_NPCS3		(1 << 20)	/* A: SPI Peripheral Chip Select 3 */
+-#define AT91_PD20_TPK8		(1 << 20)	/* B: ETM Trace Packet Port 8 */
+-#define AT91_PD21_RTS0		(1 << 21)	/* A: USART Ready To Send 0 */
+-#define AT91_PD21_TPK9		(1 << 21)	/* B: ETM Trace Packet Port 9 */
+-#define AT91_PD22_RTS1		(1 << 22)	/* A: USART Ready To Send 1 */
+-#define AT91_PD22_TPK10		(1 << 22)	/* B: ETM Trace Packet Port 10 */
+-#define AT91_PD23_RTS2		(1 << 23)	/* A: USART Ready To Send 2 */
+-#define AT91_PD23_TPK11		(1 << 23)	/* B: ETM Trace Packet Port 11 */
+-#define AT91_PD24_RTS3		(1 << 24)	/* A: USART Ready To Send 3 */
+-#define AT91_PD24_TPK12		(1 << 24)	/* B: ETM Trace Packet Port 12 */
+-#define AT91_PD25_DTR1		(1 << 25)	/* A: USART Data Terminal Ready 1 */
+-#define AT91_PD25_TPK13		(1 << 25)	/* B: ETM Trace Packet Port 13 */
+-#define AT91_PD26_TPK14		(1 << 26)	/* B: ETM Trace Packet Port 14 */
+-#define AT91_PD27_TPK15		(1 << 27)	/* B: ETM Trace Packet Port 15 */
+-#endif
+-
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91sam9260.h linux-2.6-stable/include/asm-arm/arch-at91/at91sam9260.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91sam9260.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91sam9260.h	Tue May  8 12:56:33 2007
+@@ -117,13 +117,4 @@
+ #define AT91SAM9XE_SRAM_BASE	0x00300000	/* Internal SRAM base address */
+ 
+ 
+-#if 0
+-/*
+- * PIO pin definitions (peripheral A/B multiplexing).
+- */
+-
+-// TODO: Add
+-
+-#endif
+-
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91sam9260_matrix.h linux-2.6-stable/include/asm-arm/arch-at91/at91sam9260_matrix.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91sam9260_matrix.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91sam9260_matrix.h	Fri May 11 16:20:33 2007
+@@ -67,7 +67,7 @@
+ #define		AT91_MATRIX_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
+ #define			AT91_MATRIX_CS4A_SMC		(0 << 4)
+ #define			AT91_MATRIX_CS4A_SMC_CF1	(1 << 4)
+-#define		AT91_MATRIX_CS5A		(1 << 5 )	/* Chip Select 5 Assignment */
++#define		AT91_MATRIX_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
+ #define			AT91_MATRIX_CS5A_SMC		(0 << 5)
+ #define			AT91_MATRIX_CS5A_SMC_CF2	(1 << 5)
+ #define		AT91_MATRIX_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91sam9261.h linux-2.6-stable/include/asm-arm/arch-at91/at91sam9261.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91sam9261.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91sam9261.h	Tue May  8 12:56:33 2007
+@@ -98,195 +98,4 @@
+ #define AT91SAM9261_LCDC_BASE	0x00600000	/* LDC controller */
+ 
+ 
+-#if 0
+-/*
+- * PIO pin definitions (peripheral A/B multiplexing).
+- */
+-#define AT91_PA0_SPI0_MISO	(1 <<  0)	/* A: SPI0 Master In Slave */
+-#define AT91_PA0_MCDA0		(1 <<  0)	/* B: Multimedia Card A Data 0 */
+-#define AT91_PA1_SPI0_MOSI	(1 <<  1)	/* A: SPI0 Master Out Slave */
+-#define AT91_PA1_MCCDA		(1 <<  1)	/* B: Multimedia Card A Command */
+-#define AT91_PA2_SPI0_SPCK	(1 <<  2)	/* A: SPI0 Serial Clock */
+-#define AT91_PA2_MCCK		(1 <<  2)	/* B: Multimedia Card Clock */
+-#define AT91_PA3_SPI0_NPCS0	(1 <<  3)	/* A: SPI0 Peripheral Chip Select 0 */
+-#define AT91_PA4_SPI0_NPCS1	(1 <<  4)	/* A: SPI0 Peripheral Chip Select 1 */
+-#define AT91_PA4_MCDA1		(1 <<  4)	/* B: Multimedia Card A Data 1 */
+-#define AT91_PA5_SPI0_NPCS2	(1 <<  5)	/* A: SPI0 Peripheral Chip Select 2 */
+-#define AT91_PA5_MCDA2		(1 <<  5)	/* B: Multimedia Card A Data 2 */
+-#define AT91_PA6_SPI0_NPCS3	(1 <<  6)	/* A: SPI0 Peripheral Chip Select 3 */
+-#define AT91_PA6_MCDA3		(1 <<  6)	/* B: Multimedia Card A Data 3 */
+-#define AT91_PA7_TWD		(1 <<  7)	/* A: TWI Two-wire Serial Data */
+-#define AT91_PA7_PCK0		(1 <<  7)	/* B: PMC Programmable clock Output 0 */
+-#define AT91_PA8_TWCK		(1 <<  8)	/* A: TWI Two-wire Serial Clock */
+-#define AT91_PA8_PCK1		(1 <<  8)	/* B: PMC Programmable clock Output 1 */
+-#define AT91_PA9_DRXD		(1 <<  9)	/* A: DBGU Debug Receive Data */
+-#define AT91_PA9_PCK2		(1 <<  9)	/* B: PMC Programmable clock Output 2 */
+-#define AT91_PA10_DTXD		(1 << 10)	/* A: DBGU Debug Transmit Data */
+-#define AT91_PA10_PCK3		(1 << 10)	/* B: PMC Programmable clock Output 3 */
+-#define AT91_PA11_TSYNC		(1 << 11)	/* A: Trace Synchronization Signal */
+-#define AT91_PA11_SCK1		(1 << 11)	/* B: USART1 Serial Clock */
+-#define AT91_PA12_TCLK		(1 << 12)	/* A: Trace Clock */
+-#define AT91_PA12_RTS1		(1 << 12)	/* B: USART1 Ready To Send */
+-#define AT91_PA13_TPS0		(1 << 13)	/* A: Trace ARM Pipeline Status 0 */
+-#define AT91_PA13_CTS1		(1 << 13)	/* B: USART1 Clear To Send */
+-#define AT91_PA14_TPS1		(1 << 14)	/* A: Trace ARM Pipeline Status 1 */
+-#define AT91_PA14_SCK2		(1 << 14)	/* B: USART2 Serial Clock */
+-#define AT91_PA15_TPS2		(1 << 15)	/* A: Trace ARM Pipeline Status 2 */
+-#define AT91_PA15_RTS2		(1 << 15)	/* B: USART2 Ready To Send */
+-#define AT91_PA16_TPK0		(1 << 16)	/* A: Trace Packet Port 0 */
+-#define AT91_PA16_CTS2		(1 << 16)	/* B: USART2 Clear To Send */
+-#define AT91_PA17_TPK1		(1 << 17)	/* A: Trace Packet Port 1 */
+-#define AT91_PA17_TF1		(1 << 17)	/* B: SSC1 Transmit Frame Sync */
+-#define AT91_PA18_TPK2		(1 << 18)	/* A: Trace Packet Port 2 */
+-#define AT91_PA18_TK1		(1 << 18)	/* B: SSC1 Transmit Clock */
+-#define AT91_PA19_TPK3		(1 << 19)	/* A: Trace Packet Port 3 */
+-#define AT91_PA19_TD1		(1 << 19)	/* B: SSC1 Transmit Data */
+-#define AT91_PA20_TPK4		(1 << 20)	/* A: Trace Packet Port 4 */
+-#define AT91_PA20_RD1		(1 << 20)	/* B: SSC1 Receive Data */
+-#define AT91_PA21_TPK5		(1 << 21)	/* A: Trace Packet Port 5 */
+-#define AT91_PA21_RK1		(1 << 21)	/* B: SSC1 Receive Clock */
+-#define AT91_PA22_TPK6		(1 << 22)	/* A: Trace Packet Port 6 */
+-#define AT91_PA22_RF1		(1 << 22)	/* B: SSC1 Receive Frame Sync */
+-#define AT91_PA23_TPK7		(1 << 23)	/* A: Trace Packet Port 7 */
+-#define AT91_PA23_RTS0		(1 << 23)	/* B: USART0 Ready To Send */
+-#define AT91_PA24_TPK8		(1 << 24)	/* A: Trace Packet Port 8 */
+-#define AT91_PA24_SPI1_NPCS1	(1 << 24)	/* B: SPI1 Peripheral Chip Select 1 */
+-#define AT91_PA25_TPK9		(1 << 25)	/* A: Trace Packet Port 9 */
+-#define AT91_PA25_SPI1_NPCS2	(1 << 25)	/* B: SPI1 Peripheral Chip Select 2 */
+-#define AT91_PA26_TPK10		(1 << 26)	/* A: Trace Packet Port 10 */
+-#define AT91_PA26_SPI1_NPCS3	(1 << 26)	/* B: SPI1 Peripheral Chip Select 3 */
+-#define AT91_PA27_TPK11		(1 << 27)	/* A: Trace Packet Port 11 */
+-#define AT91_PA27_SPI0_NPCS1	(1 << 27)	/* B: SPI0 Peripheral Chip Select 1 */
+-#define AT91_PA28_TPK12		(1 << 28)	/* A: Trace Packet Port 12 */
+-#define AT91_PA28_SPI0_NPCS2	(1 << 28)	/* B: SPI0 Peripheral Chip Select 2 */
+-#define AT91_PA29_TPK13		(1 << 29)	/* A: Trace Packet Port 13 */
+-#define AT91_PA29_SPI0_NPCS3	(1 << 29)	/* B: SPI0 Peripheral Chip Select 3 */
+-#define AT91_PA30_TPK14		(1 << 30)	/* A: Trace Packet Port 14 */
+-#define AT91_PA30_A23		(1 << 30)	/* B: Address Bus bit 23 */
+-#define AT91_PA31_TPK15		(1 << 31)	/* A: Trace Packet Port 15 */
+-#define AT91_PA31_A24		(1 << 31)	/* B: Address Bus bit 24 */
+-
+-#define AT91_PB0_LCDVSYNC	(1 <<  0)	/* A: LCD Vertical Synchronization */
+-#define AT91_PB1_LCDHSYNC	(1 <<  1)	/* A: LCD Horizontal Synchronization */
+-#define AT91_PB2_LCDDOTCK	(1 <<  2)	/* A: LCD Dot Clock */
+-#define AT91_PB2_PCK0		(1 <<  2)	/* B: PMC Programmable clock Output 0 */
+-#define AT91_PB3_LCDDEN		(1 <<  3)	/* A: LCD Data Enable */
+-#define AT91_PB4_LCDCC		(1 <<  4)	/* A: LCD Contrast Control */
+-#define AT91_PB4_LCDD2		(1 <<  4)	/* B: LCD Data Bus Bit 2 */
+-#define AT91_PB5_LCDD0		(1 <<  5)	/* A: LCD Data Bus Bit 0 */
+-#define AT91_PB5_LCDD3		(1 <<  5)	/* B: LCD Data Bus Bit 3 */
+-#define AT91_PB6_LCDD1		(1 <<  6)	/* A: LCD Data Bus Bit 1 */
+-#define AT91_PB6_LCDD4		(1 <<  6)	/* B: LCD Data Bus Bit 4 */
+-#define AT91_PB7_LCDD2		(1 <<  7)	/* A: LCD Data Bus Bit 2 */
+-#define AT91_PB7_LCDD5		(1 <<  7)	/* B: LCD Data Bus Bit 5 */
+-#define AT91_PB8_LCDD3		(1 <<  8)	/* A: LCD Data Bus Bit 3 */
+-#define AT91_PB8_LCDD6		(1 <<  8)	/* B: LCD Data Bus Bit 6 */
+-#define AT91_PB9_LCDD4		(1 <<  9)	/* A: LCD Data Bus Bit 4 */
+-#define AT91_PB9_LCDD7		(1 <<  9)	/* B: LCD Data Bus Bit 7 */
+-#define AT91_PB10_LCDD5		(1 << 10)	/* A: LCD Data Bus Bit 5 */
+-#define AT91_PB10_LCDD10	(1 << 10)	/* B: LCD Data Bus Bit 10 */
+-#define AT91_PB11_LCDD6		(1 << 11)	/* A: LCD Data Bus Bit 6 */
+-#define AT91_PB11_LCDD11	(1 << 11)	/* B: LCD Data Bus Bit 11 */
+-#define AT91_PB12_LCDD7		(1 << 12)	/* A: LCD Data Bus Bit 7 */
+-#define AT91_PB12_LCDD12	(1 << 12)	/* B: LCD Data Bus Bit 12 */
+-#define AT91_PB13_LCDD8		(1 << 13)	/* A: LCD Data Bus Bit 8 */
+-#define AT91_PB13_LCDD13	(1 << 13)	/* B: LCD Data Bus Bit 13 */
+-#define AT91_PB14_LCDD9		(1 << 14)	/* A: LCD Data Bus Bit 9 */
+-#define AT91_PB14_LCDD14	(1 << 14)	/* B: LCD Data Bus Bit 14 */
+-#define AT91_PB15_LCDD10	(1 << 15)	/* A: LCD Data Bus Bit 10 */
+-#define AT91_PB15_LCDD15	(1 << 15)	/* B: LCD Data Bus Bit 15 */
+-#define AT91_PB16_LCDD11	(1 << 16)	/* A: LCD Data Bus Bit 11 */
+-#define AT91_PB16_LCDD19	(1 << 16)	/* B: LCD Data Bus Bit 19 */
+-#define AT91_PB17_LCDD12	(1 << 17)	/* A: LCD Data Bus Bit 12 */
+-#define AT91_PB17_LCDD20	(1 << 17)	/* B: LCD Data Bus Bit 20 */
+-#define AT91_PB18_LCDD13	(1 << 18)	/* A: LCD Data Bus Bit 13 */
+-#define AT91_PB18_LCDD21	(1 << 18)	/* B: LCD Data Bus Bit 21 */
+-#define AT91_PB19_LCDD14	(1 << 19)	/* A: LCD Data Bus Bit 14 */
+-#define AT91_PB19_LCDD22	(1 << 19)	/* B: LCD Data Bus Bit 22 */
+-#define AT91_PB20_LCDD15	(1 << 20)	/* A: LCD Data Bus Bit 15 */
+-#define AT91_PB20_LCDD23	(1 << 20)	/* B: LCD Data Bus Bit 23 */
+-#define AT91_PB21_TF0		(1 << 21)	/* A: SSC0 Transmit Frame Sync */
+-#define AT91_PB21_LCDD16	(1 << 21)	/* B: LCD Data Bus Bit 16 */
+-#define AT91_PB22_TK0		(1 << 22)	/* A: SSC0 Transmit Clock */
+-#define AT91_PB22_LCDD17	(1 << 22)	/* B: LCD Data Bus Bit 17 */
+-#define AT91_PB23_TD0		(1 << 23)	/* A: SSC0 Transmit Data */
+-#define AT91_PB23_LCDD18	(1 << 23)	/* B: LCD Data Bus Bit 18 */
+-#define AT91_PB24_RD0		(1 << 24)	/* A: SSC0 Receive Data */
+-#define AT91_PB24_LCDD19	(1 << 24)	/* B: LCD Data Bus Bit 19 */
+-#define AT91_PB25_RK0		(1 << 25)	/* A: SSC0 Receive Clock */
+-#define AT91_PB25_LCDD20	(1 << 25)	/* B: LCD Data Bus Bit 20 */
+-#define AT91_PB26_RF0		(1 << 26)	/* A: SSC0 Receive Frame Sync */
+-#define AT91_PB26_LCDD21	(1 << 26)	/* B: LCD Data Bus Bit 21 */
+-#define AT91_PB27_SPI1_NPCS1	(1 << 27)	/* A: SPI1 Peripheral Chip Select 1 */
+-#define AT91_PB27_LCDD22	(1 << 27)	/* B: LCD Data Bus Bit 22 */
+-#define AT91_PB28_SPI1_NPCS0	(1 << 28)	/* A: SPI1 Peripheral Chip Select 0 */
+-#define AT91_PB28_LCDD23	(1 << 28)	/* B: LCD Data Bus Bit 23 */
+-#define AT91_PB29_SPI1_SPCK	(1 << 29)	/* A: SPI1 Serial Clock */
+-#define AT91_PB29_IRQ2		(1 << 29)	/* B: Interrupt input 2 */
+-#define AT91_PB30_SPI1_MISO	(1 << 30)	/* A: SPI1 Master In Slave */
+-#define AT91_PB30_IRQ1		(1 << 30)	/* B: Interrupt input 1 */
+-#define AT91_PB31_SPI1_MOSI	(1 << 31)	/* A: SPI1 Master Out Slave */
+-#define AT91_PB31_PCK2		(1 << 31)	/* B: PMC Programmable clock Output 2 */
+-
+-#define AT91_PC0_SMOE		(1 << 0)	/* A: SmartMedia Output Enable */
+-#define AT91_PC0_NCS6		(1 << 0)	/* B: Chip Select 6 */
+-#define AT91_PC1_SMWE		(1 << 1)	/* A: SmartMedia Write Enable */
+-#define AT91_PC1_NCS7		(1 << 1)	/* B: Chip Select 7 */
+-#define AT91_PC2_NWAIT		(1 << 2)	/* A: NWAIT */
+-#define AT91_PC2_IRQ0		(1 << 2)	/* B: Interrupt input 0 */
+-#define AT91_PC3_A25_CFRNW	(1 << 3)	/* A: Address Bus[25] / Compact Flash Read Not Write */
+-#define AT91_PC4_NCS4_CFCS0	(1 << 4)	/* A: Chip Select 4 / CompactFlash Chip Select 0 */
+-#define AT91_PC5_NCS5_CFCS1	(1 << 5)	/* A: Chip Select 5 / CompactFlash Chip Select 1 */
+-#define AT91_PC6_CFCE1		(1 << 6)	/* A: CompactFlash Chip Enable 1 */
+-#define AT91_PC7_CFCE2		(1 << 7)	/* A: CompactFlash Chip Enable 2 */
+-#define AT91_PC8_TXD0		(1 << 8)	/* A: USART0 Transmit Data */
+-#define AT91_PC8_PCK2		(1 << 8)	/* B: PMC Programmable clock Output 2 */
+-#define AT91_PC9_RXD0		(1 << 9)	/* A: USART0 Receive Data */
+-#define AT91_PC9_PCK3		(1 << 9)	/* B: PMC Programmable clock Output 3 */
+-#define AT91_PC10_RTS0		(1 << 10)	/* A: USART0 Ready To Send */
+-#define AT91_PC10_SCK0		(1 << 10)	/* B: USART0 Serial Clock */
+-#define AT91_PC11_CTS0		(1 << 11)	/* A: USART0 Clear To Send */
+-#define AT91_PC11_FIQ		(1 << 11)	/* B: AIC Fast Interrupt Input */
+-#define AT91_PC12_TXD1		(1 << 12)	/* A: USART1 Transmit Data */
+-#define AT91_PC12_NCS6		(1 << 12)	/* B: Chip Select 6 */
+-#define AT91_PC13_RXD1		(1 << 13)	/* A: USART1 Receive Data */
+-#define AT91_PC13_NCS7		(1 << 13)	/* B: Chip Select 7 */
+-#define AT91_PC14_TXD2		(1 << 14)	/* A: USART2 Transmit Data */
+-#define AT91_PC14_SPI1_NPCS2	(1 << 14)	/* B: SPI1 Peripheral Chip Select 2 */
+-#define AT91_PC15_RXD2		(1 << 15)	/* A: USART2 Receive Data */
+-#define AT91_PC15_SPI1_NPCS3	(1 << 15)	/* B: SPI1 Peripheral Chip Select 3 */
+-#define AT91_PC16_D16		(1 << 16)	/* A: Data Bus [16] */
+-#define AT91_PC16_TCLK0		(1 << 16)	/* B: Timer Counter 0 external clock input */
+-#define AT91_PC17_D17		(1 << 17)	/* A: Data Bus [17] */
+-#define AT91_PC17_TCLK1		(1 << 17)	/* B: Timer Counter 1 external clock input */
+-#define AT91_PC18_D18		(1 << 18)	/* A: Data Bus [18] */
+-#define AT91_PC18_TCLK2		(1 << 18)	/* B: Timer Counter 2 external clock input */
+-#define AT91_PC19_D19		(1 << 19)	/* A: Data Bus [19] */
+-#define AT91_PC19_TIOA0		(1 << 19)	/* B: Timer Counter 0 Multipurpose Timer I/O Pin A */
+-#define AT91_PC20_D20		(1 << 20)	/* A: Data Bus [20] */
+-#define AT91_PC20_TIOB0		(1 << 20)	/* B: Timer Counter 0 Multipurpose Timer I/O Pin B */
+-#define AT91_PC21_D21		(1 << 21)	/* A: Data Bus [21] */
+-#define AT91_PC21_TIOA1		(1 << 21)	/* B: Timer Counter 1 Multipurpose Timer I/O Pin A */
+-#define AT91_PC22_D22		(1 << 22)	/* A: Data Bus [22] */
+-#define AT91_PC22_TIOB1		(1 << 22)	/* B: Timer Counter 1 Multipurpose Timer I/O Pin B */
+-#define AT91_PC23_D23		(1 << 23)	/* A: Data Bus [23] */
+-#define AT91_PC23_TIOA2		(1 << 23)	/* B: Timer Counter 2 Multipurpose Timer I/O Pin A */
+-#define AT91_PC24_D24		(1 << 24)	/* A: Data Bus [24] */
+-#define AT91_PC24_TIOB2		(1 << 24)	/* B: Timer Counter 2 Multipurpose Timer I/O Pin B */
+-#define AT91_PC25_D25		(1 << 25)	/* A: Data Bus [25] */
+-#define AT91_PC25_TF2		(1 << 25)	/* B: SSC2 Transmit Frame Sync */
+-#define AT91_PC26_D26		(1 << 26)	/* A: Data Bus [26] */
+-#define AT91_PC26_TK2		(1 << 26)	/* B: SSC2 Transmit Clock */
+-#define AT91_PC27_D27		(1 << 27)	/* A: Data Bus [27] */
+-#define AT91_PC27_TD2		(1 << 27)	/* B: SSC2 Transmit Data */
+-#define AT91_PC28_D28		(1 << 28)	/* A: Data Bus [28] */
+-#define AT91_PC28_RD2		(1 << 28)	/* B: SSC2 Receive Data */
+-#define AT91_PC29_D29		(1 << 29)	/* A: Data Bus [29] */
+-#define AT91_PC29_RK2		(1 << 29)	/* B: SSC2 Receive Clock */
+-#define AT91_PC30_D30		(1 << 30)	/* A: Data Bus [30] */
+-#define AT91_PC30_RF2		(1 << 30)	/* B: SSC2 Receive Frame Sync */
+-#define AT91_PC31_D31		(1 << 31)	/* A: Data Bus [31] */
+-#define AT91_PC31_PCK1		(1 << 31)	/* B: PMC Programmable clock Output 1 */
+-#endif
+-
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91sam9263.h linux-2.6-stable/include/asm-arm/arch-at91/at91sam9263.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91sam9263.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91sam9263.h	Tue May  8 12:56:33 2007
+@@ -119,13 +119,5 @@
+ #define AT91SAM9263_DMAC_BASE	0x00800000	/* DMA Controller */
+ #define AT91SAM9263_UHP_BASE	0x00a00000	/* USB Host controller */
+ 
+-#if 0
+-/*
+- * PIO pin definitions (peripheral A/B multiplexing).
+- */
+-
+-// TODO: Add
+-
+-#endif
+ 
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91sam9rl.h linux-2.6-stable/include/asm-arm/arch-at91/at91sam9rl.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91sam9rl.h	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91sam9rl.h	Fri May 11 14:53:48 2007
+@@ -0,0 +1,110 @@
++/*
++ * include/asm-arm/arch-at91/at91sam9260.h
++ *
++ *  Copyright (C) 2007 Atmel Corporation
++ *
++ * Common definitions.
++ * Based on AT91SAM9RL datasheet revision A. (Preliminary)
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file COPYING in the main directory of this archive for
++ * more details.
++ */
++
++#ifndef AT91SAM9RL_H
++#define AT91SAM9RL_H
++
++/*
++ * Peripheral identifiers/interrupts.
++ */
++#define AT91_ID_FIQ		0	/* Advanced Interrupt Controller (FIQ) */
++#define AT91_ID_SYS		1	/* System Controller */
++#define AT91SAM9RL_ID_PIOA	2	/* Parallel IO Controller A */
++#define AT91SAM9RL_ID_PIOB	3	/* Parallel IO Controller B */
++#define AT91SAM9RL_ID_PIOC	4	/* Parallel IO Controller C */
++#define AT91SAM9RL_ID_PIOD	5	/* Parallel IO Controller D */
++#define AT91SAM9RL_ID_US0	6	/* USART 0 */
++#define AT91SAM9RL_ID_US1	7	/* USART 1 */
++#define AT91SAM9RL_ID_US2	8	/* USART 2 */
++#define AT91SAM9RL_ID_US3	9	/* USART 3 */
++#define AT91SAM9RL_ID_MCI	10	/* Multimedia Card Interface */
++#define AT91SAM9RL_ID_TWI0	11	/* TWI 0 */
++#define AT91SAM9RL_ID_TWI1	12	/* TWI 1 */
++#define AT91SAM9RL_ID_SPI	13	/* Serial Peripheral Interface */
++#define AT91SAM9RL_ID_SSC0	14	/* Serial Synchronous Controller 0 */
++#define AT91SAM9RL_ID_SSC1	15	/* Serial Synchronous Controller 1 */
++#define AT91SAM9RL_ID_TC0	16	/* Timer Counter 0 */
++#define AT91SAM9RL_ID_TC1	17	/* Timer Counter 1 */
++#define AT91SAM9RL_ID_TC2	18	/* Timer Counter 2 */
++#define AT91SAM9RL_ID_PWMC	19	/* Pulse Width Modulation Controller */
++#define AT91SAM9RL_ID_TSC	20	/* Touch Screen Controller */
++#define AT91SAM9RL_ID_DMA	21	/* DMA Controller */
++#define AT91SAM9RL_ID_UDPHS	22	/* USB Device HS */
++#define AT91SAM9RL_ID_LCDC	23	/* LCD Controller */
++#define AT91SAM9RL_ID_AC97C	24	/* AC97 Controller */
++#define AT91SAM9RL_ID_IRQ0	31	/* Advanced Interrupt Controller (IRQ0) */
++
++
++/*
++ * User Peripheral physical base addresses.
++ */
++#define AT91SAM9RL_BASE_TCB0	0xfffa0000
++#define AT91SAM9RL_BASE_TC0	0xfffa0000
++#define AT91SAM9RL_BASE_TC1	0xfffa0040
++#define AT91SAM9RL_BASE_TC2	0xfffa0080
++#define AT91SAM9RL_BASE_MCI	0xfffa4000
++#define AT91SAM9RL_BASE_TWI0	0xfffa8000
++#define AT91SAM9RL_BASE_TWI1	0xfffac000
++#define AT91SAM9RL_BASE_US0	0xfffb0000
++#define AT91SAM9RL_BASE_US1	0xfffb4000
++#define AT91SAM9RL_BASE_US2	0xfffb8000
++#define AT91SAM9RL_BASE_US3	0xfffbc000
++#define AT91SAM9RL_BASE_SSC0	0xfffc0000
++#define AT91SAM9RL_BASE_SSC1	0xfffc4000
++#define AT91SAM9RL_BASE_PWMC	0xfffc8000
++#define AT91SAM9RL_BASE_SPI	0xfffcc000
++#define AT91SAM9RL_BASE_TSC	0xfffd0000
++#define AT91SAM9RL_BASE_UDPHS	0xfffd4000
++#define AT91SAM9RL_BASE_AC97C	0xfffd8000
++#define AT91_BASE_SYS		0xffffc000
++
++
++/*
++ * System Peripherals (offset from AT91_BASE_SYS)
++ */
++#define AT91_DMA	(0xffffe600 - AT91_BASE_SYS)
++#define AT91_ECC	(0xffffe800 - AT91_BASE_SYS)
++#define AT91_SDRAMC	(0xffffea00 - AT91_BASE_SYS)
++#define AT91_SMC	(0xffffec00 - AT91_BASE_SYS)
++#define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
++#define AT91_CCFG	(0xffffef10 - AT91_BASE_SYS)
++#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
++#define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
++#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
++#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
++#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
++#define AT91_PIOD	(0xfffffa00 - AT91_BASE_SYS)
++#define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
++#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
++#define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)
++#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
++#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
++#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
++#define AT91_SCKCR	(0xfffffd50 - AT91_BASE_SYS)
++#define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
++#define AT91_RTC	(0xfffffe00 - AT91_BASE_SYS)
++
++
++/*
++ * Internal Memory.
++ */
++#define AT91SAM9RL_SRAM_BASE	0x00300000	/* Internal SRAM base address */
++#define AT91SAM9RL_SRAM_SIZE	SZ_16K		/* Internal SRAM size (16Kb) */
++
++#define AT91SAM9RL_ROM_BASE	0x00400000	/* Internal ROM base address */
++#define AT91SAM9RL_ROM_SIZE	(2 * SZ_16K)	/* Internal ROM size (32Kb) */
++
++#define AT91SAM9RL_LCDC_BASE	0x00500000	/* LCD Controller */
++#define AT91SAM9RL_UDPHS_BASE	0x00600000	/* USB Device HS controller */
++
++#endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/at91sam9rl_matrix.h linux-2.6-stable/include/asm-arm/arch-at91/at91sam9rl_matrix.h
+--- linux-2.6.21/include/asm-arm/arch-at91/at91sam9rl_matrix.h	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/include/asm-arm/arch-at91/at91sam9rl_matrix.h	Fri May 11 16:18:45 2007
+@@ -0,0 +1,96 @@
++/*
++ * include/asm-arm/arch-at91/at91sam9rl_matrix.h
++ *
++ *  Copyright (C) 2007 Atmel Corporation
++ *
++ * Memory Controllers (MATRIX, EBI) - System peripherals registers.
++ * Based on AT91SAM9RL datasheet revision A. (Preliminary)
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file COPYING in the main directory of this archive for
++ * more details.
++ */
++
++#ifndef AT91SAM9RL_MATRIX_H
++#define AT91SAM9RL_MATRIX_H
++
++#define AT91_MATRIX_MCFG0	(AT91_MATRIX + 0x00)	/* Master Configuration Register 0 */
++#define AT91_MATRIX_MCFG1	(AT91_MATRIX + 0x04)	/* Master Configuration Register 1 */
++#define AT91_MATRIX_MCFG2	(AT91_MATRIX + 0x08)	/* Master Configuration Register 2 */
++#define AT91_MATRIX_MCFG3	(AT91_MATRIX + 0x0C)	/* Master Configuration Register 3 */
++#define AT91_MATRIX_MCFG4	(AT91_MATRIX + 0x10)	/* Master Configuration Register 4 */
++#define AT91_MATRIX_MCFG5	(AT91_MATRIX + 0x14)	/* Master Configuration Register 5 */
++#define		AT91_MATRIX_ULBT	(7 << 0)	/* Undefined Length Burst Type */
++#define			AT91_MATRIX_ULBT_INFINITE	(0 << 0)
++#define			AT91_MATRIX_ULBT_SINGLE		(1 << 0)
++#define			AT91_MATRIX_ULBT_FOUR		(2 << 0)
++#define			AT91_MATRIX_ULBT_EIGHT		(3 << 0)
++#define			AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
++
++#define AT91_MATRIX_SCFG0	(AT91_MATRIX + 0x40)	/* Slave Configuration Register 0 */
++#define AT91_MATRIX_SCFG1	(AT91_MATRIX + 0x44)	/* Slave Configuration Register 1 */
++#define AT91_MATRIX_SCFG2	(AT91_MATRIX + 0x48)	/* Slave Configuration Register 2 */
++#define AT91_MATRIX_SCFG3	(AT91_MATRIX + 0x4C)	/* Slave Configuration Register 3 */
++#define AT91_MATRIX_SCFG4	(AT91_MATRIX + 0x50)	/* Slave Configuration Register 4 */
++#define AT91_MATRIX_SCFG5	(AT91_MATRIX + 0x54)	/* Slave Configuration Register 5 */
++#define		AT91_MATRIX_SLOT_CYCLE		(0xff << 0)	/* Maximum Number of Allowed Cycles for a Burst */
++#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
++#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
++#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
++#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
++#define		AT91_MATRIX_FIXED_DEFMSTR	(7    << 18)	/* Fixed Index of Default Master */
++#define		AT91_MATRIX_ARBT		(3    << 24)	/* Arbitration Type */
++#define			AT91_MATRIX_ARBT_ROUND_ROBIN	(0 << 24)
++#define			AT91_MATRIX_ARBT_FIXED_PRIORITY	(1 << 24)
++
++#define AT91_MATRIX_PRAS0	(AT91_MATRIX + 0x80)	/* Priority Register A for Slave 0 */
++#define AT91_MATRIX_PRAS1	(AT91_MATRIX + 0x88)	/* Priority Register A for Slave 1 */
++#define AT91_MATRIX_PRAS2	(AT91_MATRIX + 0x90)	/* Priority Register A for Slave 2 */
++#define AT91_MATRIX_PRAS3	(AT91_MATRIX + 0x98)	/* Priority Register A for Slave 3 */
++#define AT91_MATRIX_PRAS4	(AT91_MATRIX + 0xA0)	/* Priority Register A for Slave 4 */
++#define AT91_MATRIX_PRAS5	(AT91_MATRIX + 0xA8)	/* Priority Register A for Slave 5 */
++#define		AT91_MATRIX_M0PR		(3 << 0)	/* Master 0 Priority */
++#define		AT91_MATRIX_M1PR		(3 << 4)	/* Master 1 Priority */
++#define		AT91_MATRIX_M2PR		(3 << 8)	/* Master 2 Priority */
++#define		AT91_MATRIX_M3PR		(3 << 12)	/* Master 3 Priority */
++#define		AT91_MATRIX_M4PR		(3 << 16)	/* Master 4 Priority */
++#define		AT91_MATRIX_M5PR		(3 << 20)	/* Master 5 Priority */
++
++#define AT91_MATRIX_MRCR	(AT91_MATRIX + 0x100)	/* Master Remap Control Register */
++#define		AT91_MATRIX_RCB0		(1 << 0)	/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
++#define		AT91_MATRIX_RCB1		(1 << 1)	/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
++#define		AT91_MATRIX_RCB2		(1 << 2)
++#define		AT91_MATRIX_RCB3		(1 << 3)
++#define		AT91_MATRIX_RCB4		(1 << 4)
++#define		AT91_MATRIX_RCB5		(1 << 5)
++
++#define AT91_MATRIX_TCMR	(AT91_MATRIX + 0x114)	/* TCM Configuration Register */
++#define		AT91_MATRIX_ITCM_SIZE		(0xf << 0)	/* Size of ITCM enabled memory block */
++#define			AT91_MATRIX_ITCM_0		(0 << 0)
++#define			AT91_MATRIX_ITCM_16		(5 << 0)
++#define			AT91_MATRIX_ITCM_32		(6 << 0)
++#define		AT91_MATRIX_DTCM_SIZE		(0xf << 4)	/* Size of DTCM enabled memory block */
++#define			AT91_MATRIX_DTCM_0		(0 << 4)
++#define			AT91_MATRIX_DTCM_16		(5 << 4)
++#define			AT91_MATRIX_DTCM_32		(6 << 4)
++
++#define AT91_MATRIX_EBICSA	(AT91_MATRIX + 0x120)	/* EBI0 Chip Select Assignment Register */
++#define		AT91_MATRIX_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
++#define			AT91_MATRIX_CS1A_SMC		(0 << 1)
++#define			AT91_MATRIX_CS1A_SDRAMC		(1 << 1)
++#define		AT91_MATRIX_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
++#define			AT91_MATRIX_CS3A_SMC		(0 << 3)
++#define			AT91_MATRIX_CS3A_SMC_SMARTMEDIA	(1 << 3)
++#define		AT91_MATRIX_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
++#define			AT91_MATRIX_CS4A_SMC		(0 << 4)
++#define			AT91_MATRIX_CS4A_SMC_CF1	(1 << 4)
++#define		AT91_MATRIX_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
++#define			AT91_MATRIX_CS5A_SMC		(0 << 5)
++#define			AT91_MATRIX_CS5A_SMC_CF2	(1 << 5)
++#define		AT91_MATRIX_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
++#define		AT91_MATRIX_VDDIOMSEL		(1 << 16)	/* Memory voltage selection */
++#define			AT91_MATRIX_VDDIOMSEL_1_8V	(0 << 16)
++#define			AT91_MATRIX_VDDIOMSEL_3_3V	(1 << 16)
++
++
++#endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/board.h linux-2.6-stable/include/asm-arm/arch-at91/board.h
+--- linux-2.6.21/include/asm-arm/arch-at91/board.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/board.h	Thu May 10 12:21:10 2007
+@@ -62,7 +62,7 @@
+ };
+ extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
+ 
+- /* Ethernet */
++ /* Ethernet (EMAC & MACB) */
+ struct at91_eth_data {
+ 	u8		phy_irq_pin;	/* PHY IRQ */
+ 	u8		is_rmii;	/* using RMII interface? */
+@@ -114,9 +114,31 @@
+ };
+ extern void __init at91_add_device_serial(void);
+ 
++ /* LCD Controller */
++struct atmel_lcdfb_info;
++extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
++
++ /* AC97 */
++struct atmel_ac97_data {
++	u8		reset_pin;	/* reset */
++};
++extern void __init at91_add_device_ac97(struct atmel_ac97_data *data);
++
++ /* ISI */
++extern void __init at91_add_device_isi(void);
++
+  /* LEDs */
+ extern u8 at91_leds_cpu;
+ extern u8 at91_leds_timer;
+ extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
+ 
++struct at91_gpio_led {
++	u8		index;		/* index of LED */
++	char*		name;		/* name of LED */
++	u8		gpio;		/* AT91_PIN_xx */
++	u8		flags;		/* 1=active-high */
++	char*		trigger;	/* default trigger */
++};
++extern void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr);
++
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/cpu.h linux-2.6-stable/include/asm-arm/arch-at91/cpu.h
+--- linux-2.6.21/include/asm-arm/arch-at91/cpu.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/cpu.h	Wed May  9 10:20:54 2007
+@@ -26,6 +26,8 @@
+ #define ARCH_ID_AT91SAM9XE256	0x329a93a0
+ #define ARCH_ID_AT91SAM9XE512	0x329aa3a0
+ 
++#define ARCH_ID_AT91SAM9RL64	0x019b03a0
++
+ static inline unsigned long at91_cpu_identify(void)
+ {
+ 	return (at91_sys_read(AT91_DBGU_CIDR) & ~AT91_CIDR_VERSION);
+@@ -68,4 +70,10 @@
+ #define cpu_is_at91sam9263()	(0)
+ #endif
+ 
++#ifdef CONFIG_ARCH_AT91SAM9RL
++#define cpu_is_at91sam9rl()	(at91_cpu_identify() == ARCH_ID_AT91SAM9RL64)
++#else
++#define cpu_is_at91sam9rl()	(0)
++#endif
++
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/hardware.h linux-2.6-stable/include/asm-arm/arch-at91/hardware.h
+--- linux-2.6.21/include/asm-arm/arch-at91/hardware.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/hardware.h	Fri May 11 14:45:12 2007
+@@ -24,6 +24,8 @@
+ #include <asm/arch/at91sam9261.h>
+ #elif defined(CONFIG_ARCH_AT91SAM9263)
+ #include <asm/arch/at91sam9263.h>
++#elif defined(CONFIG_ARCH_AT91SAM9RL)
++#include <asm/arch/at91sam9rl.h>
+ #else
+ #error "Unsupported AT91 processor"
+ #endif
+@@ -69,22 +71,5 @@
+ /* Clocks */
+ #define AT91_SLOW_CLOCK		32768		/* slow clock */
+ 
+-#ifndef __ASSEMBLY__
+-#include <asm/io.h>
+-
+-static inline unsigned int at91_sys_read(unsigned int reg_offset)
+-{
+-	void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS;
+-
+-	return __raw_readl(addr + reg_offset);
+-}
+-
+-static inline void at91_sys_write(unsigned int reg_offset, unsigned long value)
+-{
+-	void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS;
+-
+-	__raw_writel(value, addr + reg_offset);
+-}
+-#endif
+ 
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/ics1523.h linux-2.6-stable/include/asm-arm/arch-at91/ics1523.h
+--- linux-2.6.21/include/asm-arm/arch-at91/ics1523.h	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/include/asm-arm/arch-at91/ics1523.h	Tue May  8 12:13:31 2007
+@@ -0,0 +1,154 @@
++//*----------------------------------------------------------------------------
++//*         ATMEL Microcontroller Software Support  -  ROUSSET  -
++//*----------------------------------------------------------------------------
++//* The software is delivered "AS IS" without warranty or condition of any
++//* kind, either express, implied or statutory. This includes without
++//* limitation any warranty or condition with respect to merchantability or
++//* fitness for any particular purpose, or against the infringements of
++//* intellectual property rights of others.
++//*----------------------------------------------------------------------------
++//* File Name           : ics1523.h
++//* Object              : Clock Generator Prototyping File.
++//*
++//* 1.0 08/28/02 ED     : Creation
++//* 1.2 13/01/03 FB		: Update on lib V3
++//*----------------------------------------------------------------------------
++
++#ifndef ics1523_h
++#define ics1523_h
++
++/*-------------------------------------------*/
++/* ICS1523 TWI Serial Clock Definition       */
++/*-------------------------------------------*/
++
++#define		ICS_MIN_CLOCK		100		/* Min Frequency Access Clock KHz */
++#define		ICS_MAX_CLOCK		400		/* Max Frequency Access Clock KHz */
++#define		ICS_TRANSFER_RATE	ICS_MAX_CLOCK	/* Transfer speed to apply */
++
++#define		ICS_WRITE_CLK_PNB	30		/* TWCK Clock Periods required to write */
++#define		ICS_READ_CLK_PNB	40		/* TWCK Clock Periods required to read */
++
++/*-------------------------------------------*/
++/* ICS1523 Write Operation Definition        */
++/*-------------------------------------------*/
++
++#define		ICS1523_ACCESS_OK	0		/* OK */
++#define		ICS1523_ACCESS_ERROR	-1		/* NOK */
++
++/*-------------------------------------------*/
++/* ICS1523 Device Addresses Definition       */
++/*-------------------------------------------*/
++
++#define		ICS_ADDR		0x26		/* Device Address */
++
++/*--------------------------------------------------*/
++/* ICS1523 Registers Internal Addresses Definition  */
++/*--------------------------------------------------*/
++
++#define		ICS_ICR			0x0		/* Input Control Register */
++#define		ICS_LCR			0x1		/* Loop Control Register */
++#define		ICS_FD0			0x2		/* PLL FeedBack Divider LSBs */
++#define		ICS_FD1			0x3		/* PLL FeedBack Divider MSBs */
++#define		ICS_DPAO		0x4		/* Dynamic Phase Aligner Offset */
++#define		ICS_DPAC		0x5		/* Dynamic Phase Aligner Resolution */
++#define		ICS_OE			0x6		/* Output Enables Register */
++#define		ICS_OD			0x7		/* Osc Divider Register */
++#define		ICS_SWRST		0x8		/* DPA & PLL Reset Register */
++#define		ICS_VID			0x10		/* Chip Version Register */
++#define		ICS_RID			0x11		/* Chip Revision Register */
++#define		ICS_SR			0x12		/* Status Register */
++
++/*------------------------------------------------------*/
++/* ICS1523 Input Control Register Bits Definition       */
++/*------------------------------------------------------*/
++
++#define		ICS_PDEN		0x1		/* Phase Detector Enable */
++#define		ICS_PDPOL		0x2		/* Phase Detector Enable Polarity */
++#define		ICS_REFPOL		0x4		/* External Reference Polarity */
++#define		ICS_FBKPOL		0x8		/* External Feedback Polarity */
++#define		ICS_FBKSEL		0x10		/* External Feedback Select */
++#define		ICS_FUNCSEL		0x20		/* Function Out Select */
++#define		ICS_ENPLS		0x40		/* Enable PLL Lock/Ref Status Output */
++#define		ICS_ENDLS		0x80		/* Enable DPA Lock/Ref Status Output */
++
++/*-----------------------------------------------------*/
++/* ICS1523 Loop Control Register Bits Definition       */
++/*-----------------------------------------------------*/
++
++#define		ICS_PFD			0x7		/* Phase Detector Gain */
++#define		ICS_PSD			0x30		/* Post-Scaler Divider */
++
++/*----------------------------------------------------*/
++/* ICS1523 PLL FeedBack Divider LSBs Definition       */
++/*----------------------------------------------------*/
++
++#define		ICS_FBDL		0xFF		/* PLL FeedBack Divider LSBs */
++
++/*----------------------------------------------------*/
++/* ICS1523 PLL FeedBack Divider MSBs Definition       */
++/*----------------------------------------------------*/
++
++#define		ICS_FBDM		0xF		/* PLL FeedBack Divider MSBs */
++
++/*------------------------------------------------------------*/
++/* ICS1523 Dynamic Phase Aligner Offset Bits Definition       */
++/*------------------------------------------------------------*/
++
++#define		ICS_DPAOS		0x2F		/* Dynamic Phase Aligner Offset */
++#define		ICS_FILSEL		0x80		/* Loop Filter Select */
++
++/*----------------------------------------------------------------*/
++/* ICS1523 Dynamic Phase Aligner Resolution Bits Definition       */
++/*----------------------------------------------------------------*/
++
++#define		ICS_DPARES		0x3		/* Dynamic Phase Aligner Resolution */
++#define		ICS_MMREV		0xFC		/* Metal Mask Revision Number */
++
++/*-------------------------------------------------------*/
++/* ICS1523 Output Enables Register Bits Definition       */
++/*-------------------------------------------------------*/
++
++#define		ICS_OEPCK		0x1		/* Output Enable for PECL PCLK Outputs */
++#define		ICS_OETCK		0x2		/* Output Enable for STTL CLK Output */
++#define		ICS_OEP2		0x4		/* Output Enable for PECL CLK/2 Outputs */
++#define		ICS_OET2		0x8		/* Output Enable for STTL CLK/2 Output */
++#define		ICS_OEF			0x10		/* Output Enable for STTL FUNC Output */
++#define		ICS_CLK2INV		0x20		/* CLK/2 Invert */
++#define		ICS_OSCL		0xC0		/* SSTL Clock Scaler */
++
++/*----------------------------------------------------*/
++/* ICS1523 Osc Divider Register Bits Definition       */
++/*----------------------------------------------------*/
++
++#define		ICS_OSCDIV		0x7F		/* Oscillator Divider Modulus */
++#define		ICS_INSEL		0x80		/* Input Select */
++
++/*---------------------------------------------------*/
++/* ICS1523 DPA & PLL Reset Register Definition       */
++/*---------------------------------------------------*/
++
++#define		ICS_DPAR		0x0A		/* DPA Reset Command */
++#define		ICS_PLLR		0x50		/* PLL Reset Command */
++
++/*------------------------------------------------*/
++/* ICS1523 Chip Version Register Definition       */
++/*------------------------------------------------*/
++
++#define		ICS_CHIPV		0xFF		/* Chip Version */
++
++/*-------------------------------------------------*/
++/* ICS1523 Chip Revision Register Definition       */
++/*-------------------------------------------------*/
++
++#define		ICS_CHIPR		0xFF		/* Chip Revision */
++
++/*------------------------------------------*/
++/* ICS1523 Status Register Definition       */
++/*------------------------------------------*/
++
++#define		ICS_DPALOCK		0x1		/* DPA Lock Status */
++#define		ICS_PLLLOCK		0x2		/* PLL Lock Status */
++
++int at91_ics1523_init(void);
++
++#endif /* ics1523_h */
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/io.h linux-2.6-stable/include/asm-arm/arch-at91/io.h
+--- linux-2.6.21/include/asm-arm/arch-at91/io.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/io.h	Fri May 11 14:45:12 2007
+@@ -29,4 +29,22 @@
+ #define __mem_pci(a)		(a)
+ 
+ 
++#ifndef __ASSEMBLY__
++
++static inline unsigned int at91_sys_read(unsigned int reg_offset)
++{
++	void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS;
++
++	return __raw_readl(addr + reg_offset);
++}
++
++static inline void at91_sys_write(unsigned int reg_offset, unsigned long value)
++{
++	void __iomem *addr = (void __iomem *)AT91_VA_BASE_SYS;
++
++	__raw_writel(value, addr + reg_offset);
++}
++
++#endif
++
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/irqs.h linux-2.6-stable/include/asm-arm/arch-at91/irqs.h
+--- linux-2.6.21/include/asm-arm/arch-at91/irqs.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/irqs.h	Fri May 11 14:45:12 2007
+@@ -21,6 +21,7 @@
+ #ifndef __ASM_ARCH_IRQS_H
+ #define __ASM_ARCH_IRQS_H
+ 
++#include <asm/io.h>
+ #include <asm/arch/at91_aic.h>
+ 
+ #define NR_AIC_IRQS 32
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/spi.h linux-2.6-stable/include/asm-arm/arch-at91/spi.h
+--- linux-2.6.21/include/asm-arm/arch-at91/spi.h	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/include/asm-arm/arch-at91/spi.h	Tue May  8 14:31:24 2007
+@@ -0,0 +1,54 @@
++/*
++ * Serial Peripheral Interface (SPI) driver for the Atmel AT91RM9200
++ *
++ * (c) SAN People (Pty) Ltd
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version
++ * 2 of the License, or (at your option) any later version.
++ */
++
++#ifndef AT91_LEGACY_SPI_H
++#define AT91_LEGACY_SPI_H
++
++#define SPI_MAJOR		153	/* registered device number */
++
++#define DEFAULT_SPI_CLK		6000000
++
++
++/* Maximum number of buffers in a single SPI transfer.
++ *  DataFlash uses maximum of 2
++ *  spidev interface supports up to 8.
++ */
++#define MAX_SPI_TRANSFERS	8
++#define NR_SPI_DEVICES		4	/* number of devices on SPI bus */
++
++/*
++ * Describes the buffers for a SPI transfer.
++ * A transmit & receive buffer must be specified for each transfer
++ */
++struct spi_transfer_list {
++	void* tx[MAX_SPI_TRANSFERS];	/* transmit */
++	int txlen[MAX_SPI_TRANSFERS];
++	void* rx[MAX_SPI_TRANSFERS];	/* receive */
++	int rxlen[MAX_SPI_TRANSFERS];
++	int nr_transfers;		/* number of transfers */
++	int curr;			/* current transfer */
++};
++
++struct spi_local {
++	unsigned int pcs;		/* Peripheral Chip Select value */
++
++	struct spi_transfer_list *xfers;	/* current transfer list */
++	dma_addr_t tx, rx;		/* DMA address for current transfer */
++	dma_addr_t txnext, rxnext;	/* DMA address for next transfer */
++};
++
++
++/* Exported functions */
++extern void spi_access_bus(short device);
++extern void spi_release_bus(short device);
++extern int spi_transfer(struct spi_transfer_list* list);
++
++#endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/timex.h linux-2.6-stable/include/asm-arm/arch-at91/timex.h
+--- linux-2.6.21/include/asm-arm/arch-at91/timex.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/timex.h	Wed May  9 10:20:53 2007
+@@ -37,6 +37,11 @@
+ #define AT91SAM9_MASTER_CLOCK	99959500
+ #define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
+ 
++#elif defined(CONFIG_ARCH_AT91SAM9RL)
++
++#define AT91SAM9_MASTER_CLOCK	100000000
++#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
++
+ #endif
+ 
+ #endif
+diff -urN -x CVS linux-2.6.21/include/asm-arm/arch-at91/uncompress.h linux-2.6-stable/include/asm-arm/arch-at91/uncompress.h
+--- linux-2.6.21/include/asm-arm/arch-at91/uncompress.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/asm-arm/arch-at91/uncompress.h	Fri May 11 14:45:12 2007
+@@ -21,7 +21,7 @@
+ #ifndef __ASM_ARCH_UNCOMPRESS_H
+ #define __ASM_ARCH_UNCOMPRESS_H
+ 
+-#include <asm/hardware.h>
++#include <asm/io.h>
+ #include <asm/arch/at91_dbgu.h>
+ 
+ /*
+diff -urN -x CVS linux-2.6.21/include/linux/clk.h linux-2.6-stable/include/linux/clk.h
+--- linux-2.6.21/include/linux/clk.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/linux/clk.h	Tue May  8 12:13:31 2007
+@@ -121,4 +121,24 @@
+  */
+ struct clk *clk_get_parent(struct clk *clk);
+ 
++/**
++ * clk_must_disable - report whether a clock's users must disable it
++ * @clk: one node in the clock tree
++ *
++ * This routine returns true only if the upcoming system state requires
++ * disabling the specified clock.
++ *
++ * It's common for platform power states to constrain certain clocks (and
++ * their descendants) to be unavailable, while other states allow that
++ * clock to be active.  A platform's power states often include an "all on"
++ * mode; system wide sleep states like "standby" or "suspend-to-RAM"; and
++ * operating states which sacrifice functionality for lower power usage.
++ *
++ * The constraint value is commonly tested in device driver suspend(), to
++ * leave clocks active if they are needed for features like wakeup events.
++ * On platforms that support reduced functionality operating states, the
++ * constraint may also need to be tested during resume() and probe() calls.
++ */
++int clk_must_disable(struct clk *clk);
++
+ #endif
+diff -urN -x CVS linux-2.6.21/include/linux/i2c-id.h linux-2.6-stable/include/linux/i2c-id.h
+--- linux-2.6.21/include/linux/i2c-id.h	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/include/linux/i2c-id.h	Tue May  8 12:13:31 2007
+@@ -202,6 +202,7 @@
+ 
+ /* --- PCA 9564 based algorithms */
+ #define I2C_HW_A_ISA		0x1a0000 /* generic ISA Bus interface card */
++#define I2C_HW_A_PLAT		0x1a0001 /* generic platform_bus interface */
+ 
+ /* --- ACPI Embedded controller algorithms                              */
+ #define I2C_HW_ACPI_EC          0x1f0000
+diff -urN -x CVS linux-2.6.21/include/video/atmel_lcdc.h linux-2.6-stable/include/video/atmel_lcdc.h
+--- linux-2.6.21/include/video/atmel_lcdc.h	Thu Jan  1 02:00:00 1970
++++ linux-2.6-stable/include/video/atmel_lcdc.h	Thu May 10 12:34:01 2007
+@@ -0,0 +1,196 @@
++/*
++ *  Header file for AT91/AT32 LCD Controller
++ *
++ *  Data structure and register user interface
++ *
++ *  Copyright (C) 2007 Atmel Corporation
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++#ifndef __ATMEL_LCDC_H__
++#define __ATMEL_LCDC_H__
++
++ /* LCD Controller info data structure */
++struct atmel_lcdfb_info {
++	spinlock_t		lock;
++	struct fb_info		*info;
++	void __iomem		*mmio;
++	unsigned long		irq_base;
++
++	unsigned int		guard_time;
++	struct platform_device	*pdev;
++	struct clk		*bus_clk;
++	struct clk		*lcdc_clk;
++	unsigned int		default_bpp;
++	unsigned int		default_lcdcon2;
++	unsigned int		default_dmacon;
++	void (*atmel_lcdfb_power_control)(int on);
++	struct fb_monspecs	*default_monspecs;
++	u32			pseudo_palette[16];
++};
++
++#define ATMEL_LCDC_DMABADDR1	0x00
++#define ATMEL_LCDC_DMABADDR2	0x04
++#define ATMEL_LCDC_DMAFRMPT1	0x08
++#define ATMEL_LCDC_DMAFRMPT2	0x0c
++#define ATMEL_LCDC_DMAFRMADD1	0x10
++#define ATMEL_LCDC_DMAFRMADD2	0x14
++
++#define ATMEL_LCDC_DMAFRMCFG	0x18
++#define	ATMEL_LCDC_FRSIZE	(0x7fffff <<  0)
++#define	ATMEL_LCDC_BLENGTH_OFFSET	24
++#define	ATMEL_LCDC_BLENGTH	(0x7f     << ATMEL_LCDC_BLENGTH_OFFSET)
++
++#define ATMEL_LCDC_DMACON	0x1c
++#define	ATMEL_LCDC_DMAEN	(0x1 << 0)
++#define	ATMEL_LCDC_DMARST	(0x1 << 1)
++#define	ATMEL_LCDC_DMABUSY	(0x1 << 2)
++#define		ATMEL_LCDC_DMAUPDT	(0x1 << 3)
++#define		ATMEL_LCDC_DMA2DEN	(0x1 << 4)
++
++#define ATMEL_LCDC_DMA2DCFG	0x20
++#define		ATMEL_LCDC_ADDRINC_OFFSET	0
++#define		ATMEL_LCDC_ADDRINC		(0xffff)
++#define		ATMEL_LCDC_PIXELOFF_OFFSET	24
++#define		ATMEL_LCDC_PIXELOFF		(0x1f << 24)
++
++#define ATMEL_LCDC_LCDCON1	0x0800
++#define	ATMEL_LCDC_BYPASS	(1     <<  0)
++#define	ATMEL_LCDC_CLKVAL_OFFSET	12
++#define	ATMEL_LCDC_CLKVAL	(0x1ff << ATMEL_LCDC_CLKVAL_OFFSET)
++#define	ATMEL_LCDC_LINCNT	(0x7ff << 21)
++
++#define ATMEL_LCDC_LCDCON2	0x0804
++#define	ATMEL_LCDC_DISTYPE	(3 << 0)
++#define		ATMEL_LCDC_DISTYPE_STNMONO	(0 << 0)
++#define		ATMEL_LCDC_DISTYPE_STNCOLOR	(1 << 0)
++#define		ATMEL_LCDC_DISTYPE_TFT		(2 << 0)
++#define	ATMEL_LCDC_SCANMOD	(1 << 2)
++#define		ATMEL_LCDC_SCANMOD_SINGLE	(0 << 2)
++#define		ATMEL_LCDC_SCANMOD_DUAL		(1 << 2)
++#define	ATMEL_LCDC_IFWIDTH	(3 << 3)
++#define		ATMEL_LCDC_IFWIDTH_4		(0 << 3)
++#define		ATMEL_LCDC_IFWIDTH_8		(1 << 3)
++#define		ATMEL_LCDC_IFWIDTH_16		(2 << 3)
++#define	ATMEL_LCDC_PIXELSIZE	(7 << 5)
++#define		ATMEL_LCDC_PIXELSIZE_1		(0 << 5)
++#define		ATMEL_LCDC_PIXELSIZE_2		(1 << 5)
++#define		ATMEL_LCDC_PIXELSIZE_4		(2 << 5)
++#define		ATMEL_LCDC_PIXELSIZE_8		(3 << 5)
++#define		ATMEL_LCDC_PIXELSIZE_16		(4 << 5)
++#define		ATMEL_LCDC_PIXELSIZE_24		(5 << 5)
++#define		ATMEL_LCDC_PIXELSIZE_32		(6 << 5)
++#define	ATMEL_LCDC_INVVD	(1 << 8)
++#define		ATMEL_LCDC_INVVD_NORMAL		(0 << 8)
++#define		ATMEL_LCDC_INVVD_INVERTED	(1 << 8)
++#define	ATMEL_LCDC_INVFRAME	(1 << 9 )
++#define		ATMEL_LCDC_INVFRAME_NORMAL	(0 << 9)
++#define		ATMEL_LCDC_INVFRAME_INVERTED	(1 << 9)
++#define	ATMEL_LCDC_INVLINE	(1 << 10)
++#define		ATMEL_LCDC_INVLINE_NORMAL	(0 << 10)
++#define		ATMEL_LCDC_INVLINE_INVERTED	(1 << 10)
++#define	ATMEL_LCDC_INVCLK	(1 << 11)
++#define		ATMEL_LCDC_INVCLK_NORMAL	(0 << 11)
++#define		ATMEL_LCDC_INVCLK_INVERTED	(1 << 11)
++#define	ATMEL_LCDC_INVDVAL	(1 << 12)
++#define		ATMEL_LCDC_INVDVAL_NORMAL	(0 << 12)
++#define		ATMEL_LCDC_INVDVAL_INVERTED	(1 << 12)
++#define	ATMEL_LCDC_CLKMOD	(1 << 15)
++#define		ATMEL_LCDC_CLKMOD_ACTIVEDISPLAY	(0 << 15)
++#define		ATMEL_LCDC_CLKMOD_ALWAYSACTIVE	(1 << 15)
++#define	ATMEL_LCDC_MEMOR	(1 << 31)
++#define		ATMEL_LCDC_MEMOR_BIG		(0 << 31)
++#define		ATMEL_LCDC_MEMOR_LITTLE		(1 << 31)
++
++#define ATMEL_LCDC_TIM1		0x0808
++#define	ATMEL_LCDC_VFP		(0xff <<  0)
++#define	ATMEL_LCDC_VBP_OFFSET		8
++#define	ATMEL_LCDC_VBP		(0xff <<  ATMEL_LCDC_VBP_OFFSET)
++#define	ATMEL_LCDC_VPW_OFFSET		16
++#define	ATMEL_LCDC_VPW		(0x3f << ATMEL_LCDC_VPW_OFFSET)
++#define	ATMEL_LCDC_VHDLY_OFFSET		24
++#define	ATMEL_LCDC_VHDLY	(0xf  << ATMEL_LCDC_VHDLY_OFFSET)
++
++#define ATMEL_LCDC_TIM2		0x080c
++#define	ATMEL_LCDC_HBP		(0xff  <<  0)
++#define	ATMEL_LCDC_HPW_OFFSET		8
++#define	ATMEL_LCDC_HPW		(0x3f  <<  ATMEL_LCDC_HPW_OFFSET)
++#define	ATMEL_LCDC_HFP_OFFSET		21
++#define	ATMEL_LCDC_HFP		(0x7ff << ATMEL_LCDC_HFP_OFFSET)
++
++#define ATMEL_LCDC_LCDFRMCFG	0x0810
++#define	ATMEL_LCDC_LINEVAL	(0x7ff <<  0)
++#define	ATMEL_LCDC_HOZVAL_OFFSET	21
++#define	ATMEL_LCDC_HOZVAL	(0x7ff << ATMEL_LCDC_HOZVAL_OFFSET)
++
++#define ATMEL_LCDC_FIFO		0x0814
++#define	ATMEL_LCDC_FIFOTH	(0xffff)
++
++#define ATMEL_LCDC_MVAL		0x0818
++
++#define ATMEL_LCDC_DP1_2	0x081c
++#define ATMEL_LCDC_DP4_7	0x0820
++#define ATMEL_LCDC_DP3_5	0x0824
++#define ATMEL_LCDC_DP2_3	0x0828
++#define ATMEL_LCDC_DP5_7	0x082c
++#define ATMEL_LCDC_DP3_4	0x0830
++#define ATMEL_LCDC_DP4_5	0x0834
++#define ATMEL_LCDC_DP6_7	0x0838
++#define	ATMEL_LCDC_DP1_2_VAL	(0xff)
++#define	ATMEL_LCDC_DP4_7_VAL	(0xfffffff)
++#define	ATMEL_LCDC_DP3_5_VAL	(0xfffff)
++#define	ATMEL_LCDC_DP2_3_VAL	(0xfff)
++#define	ATMEL_LCDC_DP5_7_VAL	(0xfffffff)
++#define	ATMEL_LCDC_DP3_4_VAL	(0xffff)
++#define	ATMEL_LCDC_DP4_5_VAL	(0xfffff)
++#define	ATMEL_LCDC_DP6_7_VAL	(0xfffffff)
++
++#define ATMEL_LCDC_PWRCON	0x083c
++#define	ATMEL_LCDC_PWR		(1    <<  0)
++#define	ATMEL_LCDC_GUARDT_OFFSET	1
++#define	ATMEL_LCDC_GUARDT	(0x7f <<  ATMEL_LCDC_GUARDT_OFFSET)
++#define	ATMEL_LCDC_BUSY		(1    << 31)
++
++#define ATMEL_LCDC_CONTRAST_CTR	0x0840
++#define	ATMEL_LCDC_PS		(3 << 0)
++#define		ATMEL_LCDC_PS_DIV1		(0 << 0)
++#define		ATMEL_LCDC_PS_DIV2		(1 << 0)
++#define		ATMEL_LCDC_PS_DIV4		(2 << 0)
++#define		ATMEL_LCDC_PS_DIV8		(3 << 0)
++#define	ATMEL_LCDC_POL		(1 << 2)
++#define		ATMEL_LCDC_POL_NEGATIVE		(0 << 2)
++#define		ATMEL_LCDC_POL_POSITIVE		(1 << 2)
++#define	ATMEL_LCDC_ENA		(1 << 3)
++#define		ATMEL_LCDC_ENA_PWMDISABLE	(0 << 3)
++#define		ATMEL_LCDC_ENA_PWMENABLE	(1 << 3)
++
++#define ATMEL_LCDC_CONTRAST_VAL	0x0844
++#define	ATMEL_LCDC_CVAL	(0xff)
++
++#define ATMEL_LCDC_IER		0x0848
++#define ATMEL_LCDC_IDR		0x084c
++#define ATMEL_LCDC_IMR		0x0850
++#define ATMEL_LCDC_ISR		0x0854
++#define ATMEL_LCDC_ICR		0x0858
++#define	ATMEL_LCDC_LNI		(1 << 0)
++#define	ATMEL_LCDC_LSTLNI	(1 << 1)
++#define	ATMEL_LCDC_EOFI		(1 << 2)
++#define	ATMEL_LCDC_UFLWI	(1 << 4)
++#define	ATMEL_LCDC_OWRI		(1 << 5)
++#define	ATMEL_LCDC_MERI		(1 << 6)
++
++#define ATMEL_LCDC_LUT(n)	(0x0c00 + ((n)*4))
++
++#endif /* __ATMEL_LCDC_H__ */
+diff -urN -x CVS linux-2.6.21/sound/soc/at91/eti_b1_wm8731.c linux-2.6-stable/sound/soc/at91/eti_b1_wm8731.c
+--- linux-2.6.21/sound/soc/at91/eti_b1_wm8731.c	Thu Apr 26 05:08:32 2007
++++ linux-2.6-stable/sound/soc/at91/eti_b1_wm8731.c	Tue May  8 12:13:58 2007
+@@ -34,8 +34,7 @@
+ #include <sound/soc.h>
+ #include <sound/soc-dapm.h>
+ 
+-#include <asm/arch/hardware.h>
+-#include <asm/arch/at91_pio.h>
++#include <asm/hardware.h>
+ #include <asm/arch/gpio.h>
+ 
+ #include "../codecs/wm8731.h"
+@@ -48,13 +47,6 @@
+ #define	DBG(x...)
+ #endif
+ 
+-#define AT91_PIO_TF1	(1 << (AT91_PIN_PB6 - PIN_BASE) % 32)
+-#define AT91_PIO_TK1	(1 << (AT91_PIN_PB7 - PIN_BASE) % 32)
+-#define AT91_PIO_TD1	(1 << (AT91_PIN_PB8 - PIN_BASE) % 32)
+-#define AT91_PIO_RD1	(1 << (AT91_PIN_PB9 - PIN_BASE) % 32)
+-#define AT91_PIO_RK1	(1 << (AT91_PIN_PB10 - PIN_BASE) % 32)
+-#define AT91_PIO_RF1	(1 << (AT91_PIN_PB11 - PIN_BASE) % 32)
+-
+ static struct clk *pck1_clk;
+ static struct clk *pllb_clk;
+ 
+@@ -277,7 +269,6 @@
+ static int __init eti_b1_init(void)
+ {
+ 	int ret;
+-	u32 ssc_pio_lines;
+ 	struct at91_ssc_periph *ssc = eti_b1_dai.cpu_dai->private_data;
+ 
+ 	if (!request_mem_region(AT91RM9200_BASE_SSC1, SZ_16K, "soc-audio")) {
+@@ -311,19 +302,12 @@
+ 		goto fail_io_unmap;
+ 	}
+ 
+- 	ssc_pio_lines = AT91_PIO_TF1 | AT91_PIO_TK1 | AT91_PIO_TD1
+-			| AT91_PIO_RD1 /* | AT91_PIO_RK1 */ | AT91_PIO_RF1;
+-
+-	/* Reset all PIO registers and assign lines to peripheral A */
+- 	at91_sys_write(AT91_PIOB + PIO_PDR,  ssc_pio_lines);
+- 	at91_sys_write(AT91_PIOB + PIO_ODR,  ssc_pio_lines);
+- 	at91_sys_write(AT91_PIOB + PIO_IFDR, ssc_pio_lines);
+- 	at91_sys_write(AT91_PIOB + PIO_CODR, ssc_pio_lines);
+- 	at91_sys_write(AT91_PIOB + PIO_IDR,  ssc_pio_lines);
+- 	at91_sys_write(AT91_PIOB + PIO_MDDR, ssc_pio_lines);
+- 	at91_sys_write(AT91_PIOB + PIO_PUDR, ssc_pio_lines);
+- 	at91_sys_write(AT91_PIOB + PIO_ASR,  ssc_pio_lines);
+- 	at91_sys_write(AT91_PIOB + PIO_OWDR, ssc_pio_lines);
++ 	at91_set_A_periph(AT91_PIN_PB6, 0);	/* TF1 */
++ 	at91_set_A_periph(AT91_PIN_PB7, 0);	/* TK1 */
++ 	at91_set_A_periph(AT91_PIN_PB8, 0);	/* TD1 */
++ 	at91_set_A_periph(AT91_PIN_PB9, 0);	/* RD1 */
++/* 	at91_set_A_periph(AT91_PIN_PB10, 0);*/	/* RK1 */ 	
++ 	at91_set_A_periph(AT91_PIN_PB11, 0);	/* RF1 */
+ 
+ 	/*
+ 	 * Set PCK1 parent to PLLB and its rate to 12 Mhz.
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/001-vlink-machine.patch
@@ -1,1 +1,212 @@
+--- linux-2.6.21.1.orig/arch/arm/boot/compressed/head-at91rm9200.S	2007-05-28 12:22:29.000000000 +0200
++++ linux-2.6.21.1/arch/arm/boot/compressed/head-at91rm9200.S	2007-05-28 12:52:16.000000000 +0200
+@@ -61,6 +61,12 @@
+ 		cmp	r7, r3
+ 		beq	99f
+ 
++		@ FDL Versalink : 1053
++		mov   r3, #(MACH_TYPE_VLINK & 0xff)
++		orr r3, r3, #(MACH_TYPE_VLINK & 0xff00)
++		cmp r7, r3
++		beq 99f
++
+ 		@ Ajeco 1ARM : 1075
+ 		mov	r3,	#(MACH_TYPE_ONEARM & 0xff)
+ 		orr	r3, r3, #(MACH_TYPE_ONEARM & 0xff00)
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/board-vlink.c	1970-01-01 01:00:00.000000000 +0100
++++ linux-2.6.21.1/arch/arm/mach-at91/board-vlink.c	2007-05-28 13:09:54.000000000 +0200
+@@ -0,0 +1,160 @@
++/*
++ * linux/arch/arm/mach-at91/board-vlink.c
++ *
++ *  Copyright (C) 2005 SAN People
++ *  Copyright (C) 2006,2007 Guthrie Consulting
++ *
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++
++#include <linux/types.h>
++#include <linux/init.h>
++#include <linux/mm.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/spi/spi.h>
++#include <linux/mtd/physmap.h>
++
++#include <asm/hardware.h>
++#include <asm/setup.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/mach/irq.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++#include <asm/arch/at91rm9200_mc.h>
++
++#include "generic.h"
++
++
++/*
++ * Serial port configuration.
++ *    0 .. 3 = USART0 .. USART3
++ *    4      = DBGU
++ */
++static struct at91_uart_config __initdata vlink_uart_config = {
++	.console_tty	= 0,				/* ttyS0 */
++	.nr_tty		= 5,
++	.tty_map	= { 4, 1, 0, 3, 2 }		/* ttyS0, ..., ttyS4 */
++};
++
++static void __init vlink_map_io(void)
++{
++	/* Initialize processor: 18.432 MHz crystal */
++	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
++
++	/* Setup the LEDs */
++//	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
++
++	/* Setup the serial ports and console */
++	at91_init_serial(&vlink_uart_config);
++}
++
++static void __init vlink_init_irq(void)
++{
++	at91rm9200_init_interrupts(NULL);
++}
++
++static struct at91_eth_data __initdata vlink_eth_data = {
++	.phy_irq_pin	= AT91_PIN_PC4,
++	.is_rmii	= 1,
++};
++
++static struct at91_usbh_data __initdata vlink_usbh_data = {
++	.ports		= 1,
++};
++
++static struct at91_udc_data __initdata vlink_udc_data = {
++	.vbus_pin	= AT91_PIN_PD4,
++	.pullup_pin	= AT91_PIN_PD5,
++};
++
++static struct at91_mmc_data __initdata vlink_mmc_data = {
++//	.det_pin	= AT91_PIN_PB27,
++	.slot_b		= 0,
++	.wire4		= 1,
++//	.wp_pin		= AT91_PIN_PA17,
++};
++
++static struct spi_board_info vlink_spi_devices[] = {
++	{	/* DataFlash chip */
++		.modalias	= "mtd_dataflash",
++		.chip_select	= 0,
++		.max_speed_hz	= 15 * 1000 * 1000,
++	},
++#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
++	{	/* DataFlash card */
++		.modalias	= "mtd_dataflash",
++		.chip_select	= 3,
++		.max_speed_hz	= 15 * 1000 * 1000,
++	},
++#endif
++};
++
++static struct at91_gpio_led vlink_leds[] = {
++	{
++		.name		= "led0",
++		.gpio		= AT91_PIN_PB1,
++		.trigger	= "heartbeat",
++	},
++	{
++		.name		= "led1",
++		.gpio		= AT91_PIN_PB2,
++		.trigger	= "timer",
++	}
++};
++
++static void __init vlink_board_init(void)
++{
++	/* Serial */
++	at91_add_device_serial();
++	/* Ethernet */
++	at91_add_device_eth(&vlink_eth_data);
++	/* USB Host */
++	at91_add_device_usbh(&vlink_usbh_data);
++	/* USB Device */
++	at91_add_device_udc(&vlink_udc_data);
++	at91_set_multi_drive(vlink_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
++	/* I2C */
++	at91_add_device_i2c();
++	/* SPI */
++	at91_add_device_spi(vlink_spi_devices, ARRAY_SIZE(vlink_spi_devices));
++#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
++	/* DataFlash card */
++//	at91_set_gpio_output(AT91_PIN_PB22, 0);
++#else
++	/* MMC */
++//	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
++	at91_add_device_mmc(0, &vlink_mmc_data);
++#endif
++	/* LEDs */
++	at91_gpio_leds(vlink_leds, ARRAY_SIZE(vlink_leds));
++}
++
++MACHINE_START(VLINK, "FDL VersaLink")
++	/* Maintainer: Guthrie Consulting */
++	.phys_io	= AT91_BASE_SYS,
++	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
++	.boot_params	= AT91_SDRAM_BASE + 0x100,
++	.timer		= &at91rm9200_timer,
++	.map_io		= vlink_map_io,
++	.init_irq	= vlink_init_irq,
++	.init_machine	= vlink_board_init,
++MACHINE_END
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/Kconfig	2007-05-28 12:22:29.000000000 +0200
++++ linux-2.6.21.1/arch/arm/mach-at91/Kconfig	2007-05-28 13:11:45.000000000 +0200
+@@ -96,6 +96,12 @@
+ 	help
+ 	  Select this if you are using Promwad's Chub board.
+ 
++config MACH_VLINK
++	bool "Figment Design Labs VersaLink"
++	depends on ARCH_AT91RM9200
++	help
++		Select this if you are using FDL's VersaLink board
++
+ endif
+ 
+ # ----------------------------------------------------------
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/Makefile	2007-05-28 12:22:29.000000000 +0200
++++ linux-2.6.21.1/arch/arm/mach-at91/Makefile	2007-05-28 13:13:15.000000000 +0200
+@@ -29,6 +29,7 @@
+ obj-$(CONFIG_MACH_ATEB9200)	+= board-eb9200.o
+ obj-$(CONFIG_MACH_KAFA)		+= board-kafa.o
+ obj-$(CONFIG_MACH_CHUB)		+= board-chub.o
++obj-$(CONFIG_MACH_VLINK)	+= board-vlink.o
+ 
+ # AT91SAM9260 board-specific support
+ obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
+@@ -51,6 +52,7 @@
+ led-$(CONFIG_MACH_CSB637)	+= leds.o
+ led-$(CONFIG_MACH_KB9200)	+= leds.o
+ led-$(CONFIG_MACH_KAFA)		+= leds.o
++led-$(CONFIG_MACH_VLINK)	+= leds.o
+ obj-$(CONFIG_LEDS) += $(led-y)
+ 
+ # VGA support
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/002-led-driver.patch
@@ -1,1 +1,190 @@
+diff -urN linux-2.6.21.1.orig/arch/arm/mach-at91/board-vlink.c linux-2.6.21.1/arch/arm/mach-at91/board-vlink.c
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/board-vlink.c	2007-05-28 13:33:41.000000000 +0200
++++ linux-2.6.21.1/arch/arm/mach-at91/board-vlink.c	2007-05-28 14:43:28.000000000 +0200
+@@ -61,7 +61,7 @@
+ 	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
+ 
+ 	/* Setup the LEDs */
+-//	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
++	at91_init_leds(AT91_PIN_PC14, AT91_PIN_PC15);
+ 
+ 	/* Setup the serial ports and console */
+ 	at91_init_serial(&vlink_uart_config);
+@@ -81,10 +81,12 @@
+ 	.ports		= 1,
+ };
+ 
++/*
+ static struct at91_udc_data __initdata vlink_udc_data = {
+ 	.vbus_pin	= AT91_PIN_PD4,
+ 	.pullup_pin	= AT91_PIN_PD5,
+ };
++*/
+ 
+ static struct at91_mmc_data __initdata vlink_mmc_data = {
+ //	.det_pin	= AT91_PIN_PB27,
+@@ -108,18 +110,19 @@
+ #endif
+ };
+ 
+-static struct at91_gpio_led vlink_leds[] = {
++/*static struct at91_gpio_led vlink_leds[] = {
+ 	{
+ 		.name		= "led0",
+-		.gpio		= AT91_PIN_PB1,
++		.gpio		= AT91_PIN_PC14,
+ 		.trigger	= "heartbeat",
+ 	},
+ 	{
+ 		.name		= "led1",
+-		.gpio		= AT91_PIN_PB2,
++		.gpio		= AT91_PIN_PC15,
+ 		.trigger	= "timer",
+ 	}
+ };
++*/
+ 
+ static void __init vlink_board_init(void)
+ {
+@@ -130,8 +133,8 @@
+ 	/* USB Host */
+ 	at91_add_device_usbh(&vlink_usbh_data);
+ 	/* USB Device */
+-	at91_add_device_udc(&vlink_udc_data);
+-	at91_set_multi_drive(vlink_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
++//	at91_add_device_udc(&vlink_udc_data);
++//	at91_set_multi_drive(vlink_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
+ 	/* I2C */
+ 	at91_add_device_i2c();
+ 	/* SPI */
+@@ -145,7 +148,7 @@
+ 	at91_add_device_mmc(0, &vlink_mmc_data);
+ #endif
+ 	/* LEDs */
+-	at91_gpio_leds(vlink_leds, ARRAY_SIZE(vlink_leds));
++//	at91_gpio_leds(vlink_leds, ARRAY_SIZE(vlink_leds));
+ }
+ 
+ MACHINE_START(VLINK, "FDL VersaLink")
+diff -urN linux-2.6.21.1.orig/arch/arm/mach-at91/Makefile linux-2.6.21.1/arch/arm/mach-at91/Makefile
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/Makefile	2007-05-28 13:13:15.000000000 +0200
++++ linux-2.6.21.1/arch/arm/mach-at91/Makefile	2007-05-28 14:19:06.000000000 +0200
+@@ -52,7 +52,7 @@
+ led-$(CONFIG_MACH_CSB637)	+= leds.o
+ led-$(CONFIG_MACH_KB9200)	+= leds.o
+ led-$(CONFIG_MACH_KAFA)		+= leds.o
+-led-$(CONFIG_MACH_VLINK)	+= leds.o
++led-$(CONFIG_MACH_VLINK)	+= vlink_leds.o
+ obj-$(CONFIG_LEDS) += $(led-y)
+ 
+ # VGA support
+diff -urN linux-2.6.21.1.orig/arch/arm/mach-at91/vlink_leds.c linux-2.6.21.1/arch/arm/mach-at91/vlink_leds.c
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/vlink_leds.c	1970-01-01 01:00:00.000000000 +0100
++++ linux-2.6.21.1/arch/arm/mach-at91/vlink_leds.c	2007-05-28 14:41:03.000000000 +0200
+@@ -0,0 +1,105 @@
++/*
++ * LED driver for Atmel AT91-based boards.
++ *
++ *  Copyright (C) SAN People (Pty) Ltd
++ *	Modified for FDL VersaLink Copyright (C) Guthrie Consulting
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version
++ * 2 of the License, or (at your option) any later version.
++*/
++
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/init.h>
++
++#include <asm/mach-types.h>
++#include <asm/leds.h>
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++
++
++static inline void at91_led_on(unsigned int led)
++{
++	at91_set_gpio_value(led, 0);
++}
++
++static inline void at91_led_off(unsigned int led)
++{
++	at91_set_gpio_value(led, 1);
++}
++
++static inline void at91_led_toggle(unsigned int led)
++{
++	unsigned long is_off = at91_get_gpio_value(led);
++	if (is_off) {
++		at91_led_on(led);
++		at91_led_off(at91_leds_cpu);
++		}
++	else {
++		at91_led_on(at91_leds_cpu);
++		at91_led_off(led);
++		}
++}
++
++
++/*
++ * Handle LED events.
++ */
++
++/*
++ * VersaLink has a single bi-coloured LED which changes colour when the
++ * polarity is reversed
++ */
++static void at91_leds_event(led_event_t evt)
++{
++	unsigned long flags;
++
++	local_irq_save(flags);
++
++	switch(evt) {
++	case led_start:		/* System startup */
++		at91_led_toggle(at91_leds_timer);
++		break;
++
++	case led_stop:		/* System stop / suspend */
++		at91_led_toggle(at91_leds_timer);
++		break;
++
++#ifdef CONFIG_LEDS_TIMER
++	case led_timer:		/* Every 50 timer ticks */
++		at91_led_toggle(at91_leds_timer);
++		break;
++#endif
++
++#ifdef CONFIG_LEDS_CPU
++	case led_idle_start:	/* Entering idle state */
++		at91_led_toggle(at91_leds_timer);
++		break;
++
++	case led_idle_end:	/* Exit idle state */
++		at91_led_toggle(at91_leds_timer);
++		break;
++#endif
++
++	default:
++		break;
++	}
++
++	local_irq_restore(flags);
++}
++
++
++static int __init leds_init(void)
++{
++	if (!at91_leds_timer || !at91_leds_cpu)
++		return -ENODEV;
++
++	leds_event = at91_leds_event;
++
++	leds_event(led_start);
++	return 0;
++}
++
++__initcall(leds_init);
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/003-gpio-driver.patch
@@ -1,1 +1,356 @@
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/gpio.c	2007-04-27 23:49:26.000000000 +0200
++++ linux-2.6.21.1/arch/arm/mach-at91/gpio.c	2007-05-28 15:30:48.000000000 +0200
+@@ -27,6 +27,7 @@
+ 
+ static struct at91_gpio_bank *gpio;
+ static int gpio_banks;
++static u32 pio_gpio_pin[4] = { 0, 0, 0, 0 };
+ 
+ 
+ static inline void __iomem *pin_to_controller(unsigned pin)
+@@ -71,9 +72,13 @@
+ {
+ 	void __iomem	*pio = pin_to_controller(pin);
+ 	unsigned	mask = pin_to_mask(pin);
++	int bank = (pin - PIN_BASE) / 32;
+ 
+ 	if (!pio)
+ 		return -EINVAL;
++
++	pio_gpio_pin[bank] |= mask;
++
+ 	__raw_writel(mask, pio + PIO_IDR);
+ 	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
+ 	__raw_writel(mask, pio + PIO_PER);
+@@ -130,10 +135,13 @@
+ {
+ 	void __iomem	*pio = pin_to_controller(pin);
+ 	unsigned	mask = pin_to_mask(pin);
++	int bank = (pin - PIN_BASE) / 32;
+ 
+ 	if (!pio)
+ 		return -EINVAL;
+ 
++	pio_gpio_pin[bank] |= mask;
++
+ 	__raw_writel(mask, pio + PIO_IDR);
+ 	__raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR));
+ 	__raw_writel(mask, pio + PIO_ODR);
+@@ -151,10 +159,13 @@
+ {
+ 	void __iomem	*pio = pin_to_controller(pin);
+ 	unsigned	mask = pin_to_mask(pin);
++	int bank = (pin - PIN_BASE) / 32;
+ 
+ 	if (!pio)
+ 		return -EINVAL;
+ 
++	pio_gpio_pin[bank] |= mask;
++
+ 	__raw_writel(mask, pio + PIO_IDR);
+ 	__raw_writel(mask, pio + PIO_PUDR);
+ 	__raw_writel(mask, pio + (value ? PIO_SODR : PIO_CODR));
+@@ -262,6 +273,18 @@
+ }
+ EXPORT_SYMBOL(at91_get_gpio_value);
+ 
++int at91_is_pin_gpio(unsigned pin)
++{
++  void __iomem  *pio = pin_to_controller(pin);
++  unsigned  mask = pin_to_mask(pin);
++  int     bank = (pin - PIN_BASE) / 32;
++
++  if (!pio)
++    return -EINVAL;
++  return (pio_gpio_pin[bank] & mask) != 0;
++}
++EXPORT_SYMBOL(at91_is_pin_gpio);
++
+ /*--------------------------------------------------------------------------*/
+ 
+ #ifdef CONFIG_PM
+--- linux-2.6.21.1.orig/drivers/char/Kconfig	2007-05-28 12:22:29.000000000 +0200
++++ linux-2.6.21.1/drivers/char/Kconfig	2007-05-28 15:37:43.000000000 +0200
+@@ -1087,5 +1087,12 @@
+ 	  The SPI driver gives user mode access to this serial
+ 	  bus on the AT91RM9200 processor.
+ 
++config AT91_VLIO
++  tristate "Versalink LED and GPIO interface"
++  depends on ARCH_AT91RM9200 && MACH_VLINK
++  default n
++  help
++    Provides a handler GPIO's in userspace
++
+ endmenu
+ 
+--- linux-2.6.21.1.orig/drivers/char/Makefile	2007-05-28 12:22:29.000000000 +0200
++++ linux-2.6.21.1/drivers/char/Makefile	2007-05-28 15:38:11.000000000 +0200
+@@ -95,6 +95,7 @@
+ obj-$(CONFIG_TELCLOCK)		+= tlclk.o
+ obj-$(CONFIG_AT91_SPI)		+= at91_spi.o
+ obj-$(CONFIG_AT91_SPIDEV)	+= at91_spidev.o
++obj-$(CONFIG_AT91_VLIO)  += vlink_giu.o
+ 
+ obj-$(CONFIG_WATCHDOG)		+= watchdog/
+ obj-$(CONFIG_MWAVE)		+= mwave/
+--- linux-2.6.21.1.orig/drivers/char/vlink_giu.c	1970-01-01 01:00:00.000000000 +0100
++++ linux-2.6.21.1/drivers/char/vlink_giu.c	2007-05-28 15:39:47.000000000 +0200
+@@ -0,0 +1,256 @@
++/*
++ *  Driver for FDL Versalink GPIO
++ *
++ *  Copyright (C) 2005 Guthrie Consulting
++ *	Author: Hamish Guthrie <hamish@prodigi.ch>
++ *
++ *  This program is free software; you can redistribute it and/or modify
++ *  it under the terms of the GNU General Public License as published by
++ *  the Free Software Foundation; either version 2 of the License, or
++ *  (at your option) any later version.
++ *
++ *  This program is distributed in the hope that it will be useful,
++ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
++ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ *  GNU General Public License for more details.
++ *
++ *  You should have received a copy of the GNU General Public License
++ *  along with this program; if not, write to the Free Software
++ *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++
++#include <linux/module.h>
++#include <linux/moduleparam.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++
++#include <linux/kernel.h>
++#include <linux/slab.h>
++#include <linux/fs.h>
++#include <linux/errno.h>
++#include <linux/init.h>
++#include <linux/types.h>
++#include <linux/proc_fs.h>
++#include <linux/fcntl.h>
++#include <linux/seq_file.h>
++#include <linux/cdev.h>
++#include <asm/arch/gpio.h>
++#include <asm/uaccess.h>
++
++static int major;	/* default is dynamic major device number */
++module_param(major, int, 0);
++MODULE_PARM_DESC(major, "Major device number");
++
++#define VIO_NR_DEVS 96
++
++struct vio_dev {
++	struct cdev cdev;
++};
++
++struct vio_dev *vio_devices;
++static struct class *vio_class;
++
++static ssize_t gpio_read(struct file *file, char __user *buf, size_t len,
++                         loff_t *ppos)
++{
++	unsigned int pin;
++	int retval;
++	char value = '0';
++
++	pin = iminor(file->f_dentry->d_inode);
++
++	retval = at91_get_gpio_value(PIN_BASE + pin);
++	if (retval < 0)
++		return -EFAULT;
++
++	value = retval + 0x30;
++	if (put_user(value, buf))
++		return -EFAULT;
++
++	return 1;
++}
++
++static ssize_t gpio_write(struct file *file, const char __user *data,
++                          size_t len, loff_t *ppos)
++{
++	unsigned int pin;
++	size_t i;
++	char c;
++	int retval = 0;
++
++	pin = iminor(file->f_dentry->d_inode);
++
++	for (i = 0; i < len; i++) {
++		if (get_user(c, data + i))
++			return -EFAULT;
++
++		switch (c) {
++		case '0':
++		case '1':
++			retval = at91_set_gpio_value(PIN_BASE + pin, (int)c - 0x30);
++			if (retval < 0)
++				return -EFAULT;
++			break;
++		default:
++			break;
++		}
++
++		if (retval < 0)
++			break;
++	}
++
++	return i;
++}
++
++static int gpio_open(struct inode *inode, struct file *file)
++{
++	return nonseekable_open(inode, file);
++}
++
++static int gpio_release(struct inode *inode, struct file *file)
++{
++	return 0;
++}
++
++static struct file_operations vio_fops = {
++	.owner		= THIS_MODULE,
++	.read		= gpio_read,
++	.write		= gpio_write,
++	.open		= gpio_open,
++	.release	= gpio_release,
++};
++
++static void vio_setup_cdev(struct vio_dev *dev, int index)
++{
++	int err, devno = MKDEV(major, index);
++
++	cdev_init(&dev->cdev, &vio_fops);
++	dev->cdev.owner = THIS_MODULE;
++	dev->cdev.ops = &vio_fops;
++	err = cdev_add (&dev->cdev, devno, 1);
++	if (err)
++		printk(KERN_NOTICE "vio: Error %d adding vio%d", err, index);
++}
++
++static int vio_remove(struct platform_device *dev)
++{
++	int i;
++	dev_t devno = MKDEV(major, 0);
++
++	if (vio_devices) {
++		for(i=0; i<VIO_NR_DEVS; i++) {
++			int iodev = at91_is_pin_gpio(PIN_BASE + i);
++			if (iodev) {
++				cdev_del(&vio_devices[i].cdev);
++				class_device_destroy(vio_class, MKDEV(major, i));
++			}
++		}
++		kfree(vio_devices);
++	}
++
++	class_destroy(vio_class);
++	unregister_chrdev_region(devno, VIO_NR_DEVS);
++
++	platform_set_drvdata(dev, NULL);
++
++	return 0;
++}
++
++static int vio_probe(struct platform_device *dev)
++{
++	int retval, i, j;
++	dev_t vdev = 0;
++
++	if (major) {
++		vdev = MKDEV(major, 0);
++		retval = register_chrdev_region(vdev, VIO_NR_DEVS, "vio");
++	} else {
++		retval = alloc_chrdev_region(&vdev, 0, VIO_NR_DEVS, "vio");
++		major = MAJOR(vdev);
++	}
++	if (retval < 0) {
++		printk(KERN_WARNING "vio: can't get major %d\n", major);
++		return retval;
++	}
++
++	if (major == 0) {
++		major = retval;
++		printk(KERN_INFO "vio: major number %d\n", major);
++	}
++
++	vio_class = class_create(THIS_MODULE, "vio");
++
++	if (IS_ERR(vio_class)) {
++		printk(KERN_ERR "vio: Error creating vio class\n");
++		vio_remove(dev);
++		return PTR_ERR(vio_class);
++	}
++
++	vio_devices = kmalloc(VIO_NR_DEVS * sizeof(struct vio_dev), GFP_KERNEL);
++	if (!vio_devices) {
++		retval = -ENOMEM;
++		goto fail;
++	}
++	memset(vio_devices, 0, VIO_NR_DEVS * sizeof(struct vio_dev));
++
++	for (i=0; i<VIO_NR_DEVS/32; i++)
++		for(j=0; j<32; j++) {
++			int iodev = at91_is_pin_gpio(PIN_BASE + i*32 + j);
++			if (iodev) {
++				vio_setup_cdev(&vio_devices[i*32 + j], i*32 + j);
++				class_device_create(vio_class, NULL, MKDEV(major, i*32 + j), NULL,
++					"vio%c%d", i + 'A', j);
++			}
++		}
++
++	platform_set_drvdata(dev, vio_devices);
++
++	return 0;
++
++fail:
++	vio_remove(dev);
++	return retval;
++}
++
++static struct platform_device *vio_platform_device;
++
++static struct platform_driver vio_driver = {
++	.probe 		= vio_probe,
++	.remove		= vio_remove,
++	.driver		= {
++		.name	= "vio",
++		.owner	= THIS_MODULE,
++	},
++};
++
++static int __init vio_init(void)
++{
++	int retval;
++
++	vio_platform_device = platform_device_register_simple("vio", -1, NULL, 0);
++	if (IS_ERR(vio_platform_device)) {
++		printk(KERN_WARNING "vio: device registration failed\n");
++		return PTR_ERR(vio_platform_device);
++	}
++
++	retval = platform_driver_register(&vio_driver);
++	if (retval < 0) {
++		printk(KERN_WARNING "vio: driver registration failed\n");
++		platform_device_unregister(vio_platform_device);
++	}
++	
++	return retval;
++}
++
++static void __exit vio_exit(void)
++{
++	platform_driver_unregister(&vio_driver);
++	platform_device_unregister(vio_platform_device);
++}
++
++module_init(vio_init);
++module_exit(vio_exit);
++
++MODULE_AUTHOR("Hamish Guthrie <hamish@prodigi.ch>");
++MODULE_DESCRIPTION("FDL Versalink GPIO Driver");
++MODULE_LICENSE("GPL");
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/006-change-gpios.patch
@@ -1,1 +1,37 @@
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/board-vlink.c	2007-05-28 15:53:31.000000000 +0200
++++ linux-2.6.21.1/arch/arm/mach-at91/board-vlink.c	2007-05-28 15:58:46.000000000 +0200
+@@ -149,6 +149,33 @@
+ #endif
+ 	/* LEDs */
+ //	at91_gpio_leds(vlink_leds, ARRAY_SIZE(vlink_leds));
++
++/* Other LED's */
++       at91_set_gpio_output(AT91_PIN_PC7, 1);  // LED FRONT AP1
++       at91_set_gpio_output(AT91_PIN_PC8, 1);  // LED FRONT BP1
++       at91_set_gpio_output(AT91_PIN_PB14, 1); // LED BACK AP1
++       at91_set_gpio_output(AT91_PIN_PB15, 1); // LED BACK BP1
++       at91_set_gpio_output(AT91_PIN_PB16, 1); // LED BACK AP2
++       at91_set_gpio_output(AT91_PIN_PB17, 1); // LED BACK BP2
++
++/* SIM Cards */
++       at91_set_gpio_output(AT91_PIN_PB9, 1);  // ENBSC3
++       at91_set_gpio_output(AT91_PIN_PB10, 1); // ENBSC2
++       at91_set_gpio_output(AT91_PIN_PB11, 1); // ENBSC1
++
++/* GSM Module Control */
++       at91_set_gpio_output(AT91_PIN_PB12, 1); // GSMONOFF
++
++/* Test jig presence detection */
++       at91_set_gpio_input(AT91_PIN_PB8, 1);   // JIGPRESENT
++
++/* Power indicator */
++       at91_set_gpio_input(AT91_PIN_PB22, 1);  // PWR_IND
++
++/* USB Device control */
++       at91_set_gpio_input(AT91_PIN_PB27, 1);  // UDB_CNX
++       at91_set_gpio_output(AT91_PIN_PB28, 1); // UDB_PUP
++
+ }
+ 
+ MACHINE_START(VLINK, "FDL VersaLink")
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/007-mtd-partition.patch
@@ -1,1 +1,37 @@
+--- linux-2.6.21.1.orig/drivers/mtd/devices/at91_dataflash.c	2007-05-28 12:22:29.000000000 +0200
++++ linux-2.6.21.1/drivers/mtd/devices/at91_dataflash.c	2007-05-28 16:10:21.000000000 +0200
+@@ -173,7 +173,7 @@
+ };
+ #endif
+ 
+-static const char *part_probes[] = { "cmdlinepart", NULL, };
++static const char *part_probes[] = { "cmdlinepart", "at91part", NULL, };
+ 
+ #endif
+ 
+--- linux-2.6.21.1.orig/drivers/mtd/Kconfig	2007-05-28 12:22:09.000000000 +0200
++++ linux-2.6.21.1/drivers/mtd/Kconfig	2007-05-28 16:09:16.000000000 +0200
+@@ -157,6 +157,12 @@
+ 	  for your particular device. It won't happen automatically. The
+ 	  'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example.
+ 
++config MTD_AT91_PARTS
++ tristate "Atmel AT91 partitioning support"
++ depends on MTD_PARTITIONS && ARCH_AT91RM9200 && AT91_SPI
++ ---help---
++   Atmel AT91 partitioning support
++
+ comment "User Modules And Translation Layers"
+ 	depends on MTD
+ 
+--- linux-2.6.21.1.orig/drivers/mtd/Makefile	2007-04-27 23:49:26.000000000 +0200
++++ linux-2.6.21.1/drivers/mtd/Makefile	2007-05-28 16:09:55.000000000 +0200
+@@ -12,6 +12,7 @@
+ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
+ obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
+ obj-$(CONFIG_MTD_AFS_PARTS)	+= afs.o
++obj-$(CONFIG_MTD_AT91_PARTS) += at91part.o
+ 
+ # 'Users' - code which presents functionality to userspace.
+ obj-$(CONFIG_MTD_CHAR)		+= mtdchar.o
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/008-fdl-serial.patch
@@ -1,1 +1,161 @@
+--- linux-2.6.21.1.orig/drivers/serial/atmel_serial.c	2007-05-28 12:22:29.000000000 +0200
++++ linux-2.6.21.1/drivers/serial/atmel_serial.c	2007-05-28 16:39:09.000000000 +0200
+@@ -174,7 +174,35 @@
+ 				at91_set_gpio_value(AT91_PIN_PA21, 0);
+ 			else
+ 				at91_set_gpio_value(AT91_PIN_PA21, 1);
++
++      /*
++       * FDL VersaLink adds GPIOS to provide full modem control on
++       * USART 0 - Drive DTR and RI pins manually
++       */
++      if (mctrl & TIOCM_DTR)
++        at91_set_gpio_value(AT91_PIN_PB6, 0);
++      else
++        at91_set_gpio_value(AT91_PIN_PB6, 1);
++      if (mctrl & TIOCM_RI)
++        at91_set_gpio_value(AT91_PIN_PB7, 0);
++      else
++        at91_set_gpio_value(AT91_PIN_PB7, 1);
+ 		}
++
++    /*
++     * FDL VersaLink adds GPIOS to provide full modem control on
++     * USART 3 - Drive DTR and RI pins manually
++     */
++    if (port->mapbase == AT91RM9200_BASE_US3) {
++      if (mctrl & TIOCM_DTR)
++        at91_set_gpio_value(AT91_PIN_PB29, 0);
++      else
++        at91_set_gpio_value(AT91_PIN_PB29, 1);
++      if (mctrl & TIOCM_RI)
++        at91_set_gpio_value(AT91_PIN_PB2, 0);
++      else
++        at91_set_gpio_value(AT91_PIN_PB2, 1);
++    }
+ 	}
+ #endif
+ 
+@@ -211,8 +239,10 @@
+ 	/*
+ 	 * The control signals are active low.
+ 	 */
+-	if (!(status & ATMEL_US_DCD))
+-		ret |= TIOCM_CD;
++
++  if (!(port->mapbase == AT91RM9200_BASE_US0 || port->mapbase == AT91RM9200_BASE_US3))
++		if (!(status & ATMEL_US_DCD))
++			ret |= TIOCM_CD;
+ 	if (!(status & ATMEL_US_CTS))
+ 		ret |= TIOCM_CTS;
+ 	if (!(status & ATMEL_US_DSR))
+@@ -220,6 +250,16 @@
+ 	if (!(status & ATMEL_US_RI))
+ 		ret |= TIOCM_RI;
+ 
++  /*
++   * Read the GPIO's for the FDL VersaLink special case
++   */
++  if (port->mapbase == AT91RM9200_BASE_US0)
++    if (!(at91_get_gpio_value(AT91_PIN_PA19)))
++      ret |= TIOCM_CD;
++  if (port->mapbase == AT91RM9200_BASE_US3)
++    if (!(at91_get_gpio_value(AT91_PIN_PA24)))
++      ret |= TIOCM_CD;
++
+ 	return ret;
+ }
+ 
+@@ -511,6 +551,34 @@
+ }
+ 
+ /*
++ * USART0 DCD Interrupt handler
++ */
++
++static irqreturn_t atmel_u0_DCD_interrupt(int irq, void *dev_id)
++{
++  struct uart_port *port = dev_id;
++  int status = at91_get_gpio_value(irq);
++
++  uart_handle_dcd_change(port, !(status));
++
++  return IRQ_HANDLED;
++}
++
++/*
++ * USART3 DCD Interrupt handler
++ */
++
++static irqreturn_t atmel_u3_DCD_interrupt(int irq, void *dev_id)
++{
++  struct uart_port *port = dev_id;
++  int status = at91_get_gpio_value(irq);
++
++  uart_handle_dcd_change(port, !(status));
++
++  return IRQ_HANDLED;
++}
++
++/*
+  * Interrupt handler
+  */
+ static irqreturn_t atmel_interrupt(int irq, void *dev_id)
+@@ -587,6 +655,23 @@
+ 		return retval;
+ 	}
+ 
++	if (port->mapbase == AT91RM9200_BASE_US0) {
++		retval = request_irq(AT91_PIN_PA19, atmel_u0_DCD_interrupt, 0, "atmel_serial", port);
++		if (retval) {
++			printk("atmel_serial: atmel_startup - Can't get u0DCD irq\n");
++			free_irq(port->irq, port);
++			return retval;
++		}
++	}
++	if (port->mapbase == AT91RM9200_BASE_US3) {
++		retval = request_irq(AT91_PIN_PA24, atmel_u3_DCD_interrupt, 0, "atmel_serial", port);
++		if (retval) {
++			printk("atmel_serial: atmel_startup - Can't get u3DCD irq\n");
++			free_irq(port->irq, port);
++			return retval;
++		}
++	}
++
+ 	/*
+ 	 * Initialize DMA (if necessary)
+ 	 */
+@@ -603,6 +688,10 @@
+ 					kfree(atmel_port->pdc_rx[0].buf);
+ 				}
+ 				free_irq(port->irq, port);
++        if (port->mapbase == AT91RM9200_BASE_US0)
++          free_irq(AT91_PIN_PA19, port);
++        if (port->mapbase == AT91RM9200_BASE_US3)
++          free_irq(AT91_PIN_PA24, port);
+ 				return -ENOMEM;
+ 			}
+ 			pdc->dma_addr = dma_map_single(port->dev, pdc->buf, PDC_BUFFER_SIZE, DMA_FROM_DEVICE);
+@@ -636,6 +725,10 @@
+ 		retval = atmel_open_hook(port);
+ 		if (retval) {
+ 			free_irq(port->irq, port);
++      if (port->mapbase == AT91RM9200_BASE_US0)
++        free_irq(AT91_PIN_PA19, port);
++      if (port->mapbase == AT91RM9200_BASE_US3)
++        free_irq(AT91_PIN_PA24, port);
+ 			return retval;
+ 		}
+ 	}
+@@ -701,6 +794,10 @@
+ 	 * Free the interrupt
+ 	 */
+ 	free_irq(port->irq, port);
++  if (port->mapbase == AT91RM9200_BASE_US0)
++    free_irq(AT91_PIN_PA19, port);
++  if (port->mapbase == AT91RM9200_BASE_US3)
++    free_irq(AT91_PIN_PA24, port);
+ 
+ 	/*
+ 	 * If there is a specific "close" function (to unregister
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/009-fdl-uartinit.patch
@@ -1,1 +1,35 @@
+--- linux-2.6.21.1.orig/arch/arm/mach-at91/at91rm9200_devices.c	2007-05-28 12:22:29.000000000 +0200
++++ linux-2.6.21.1/arch/arm/mach-at91/at91rm9200_devices.c	2007-05-28 16:44:36.000000000 +0200
+@@ -618,7 +618,6 @@
+ 
+ 
+ #if defined(CONFIG_NEW_LEDS)
+-
+ static struct platform_device at91_leds = {
+ 	.name		= "at91_leds",
+ 	.id		= -1,
+@@ -724,6 +723,10 @@
+ 	 *  We need to drive the pin manually.  Default is off (RTS is active low).
+ 	 */
+ 	at91_set_gpio_output(AT91_PIN_PA21, 1);
++	at91_set_gpio_output(AT91_PIN_PB6, 1);  /* DTR0 */
++	at91_set_gpio_output(AT91_PIN_PB7, 1);  /* RI0 */
++	at91_set_gpio_input(AT91_PIN_PA19, 1);  /* DCD0 */
++	at91_set_deglitch(AT91_PIN_PA19, 1);
+ }
+ 
+ static struct resource uart1_resources[] = {
+@@ -835,6 +838,12 @@
+ {
+ 	at91_set_B_periph(AT91_PIN_PA5, 1);		/* TXD3 */
+ 	at91_set_B_periph(AT91_PIN_PA6, 0);		/* RXD3 */
++	at91_set_B_periph(AT91_PIN_PB0, 0);   /* RTS3 */
++	at91_set_B_periph(AT91_PIN_PB1, 0);   /* CTS3 */
++	at91_set_gpio_output(AT91_PIN_PB29, 1); /* DTR0 */
++	at91_set_gpio_output(AT91_PIN_PB2, 1);  /* RI0 */
++	at91_set_gpio_input(AT91_PIN_PA24, 1);  /* DCD0 */
++	at91_set_deglitch(AT91_PIN_PA24, 1);
+ }
+ 
+ struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/010-dm9161a-phyfix.patch
@@ -1,1 +1,29 @@
+--- linux-2.6.21.1/drivers/net/arm/at91_ether.c.old	2007-06-04 18:15:49.000000000 +0200
++++ linux-2.6.21.1/drivers/net/arm/at91_ether.c	2007-06-04 18:10:36.000000000 +0200
+@@ -146,6 +146,7 @@
+ 	struct at91_private *lp = netdev_priv(dev);
+ 	unsigned int bmsr, bmcr, lpa, mac_cfg;
+ 	unsigned int speed, duplex;
++	unsigned long timeout = jiffies + HZ;
+ 
+ 	if (!mii_link_ok(&lp->mii)) {		/* no link */
+ 		netif_carrier_off(dev);
+@@ -158,8 +159,15 @@
+ 	read_phy(lp->phy_address, MII_BMSR, &bmsr);
+ 	read_phy(lp->phy_address, MII_BMCR, &bmcr);
+ 	if (bmcr & BMCR_ANENABLE) {				/* AutoNegotiation is enabled */
+-		if (!(bmsr & BMSR_ANEGCOMPLETE))
+-			return;			/* Do nothing - another interrupt generated when negotiation complete */
++		while (!(bmsr & BMSR_ANEGCOMPLETE)) {
++			if (time_after(jiffies, timeout)) {
++				printk("at91_ether: Auto-negotiate timeout\n");
++				return;
++			}
++			read_phy(lp->phy_address, MII_BMSR, &bmsr);
++			read_phy(lp->phy_address, MII_BMCR, &bmcr);
++			cpu_relax();
++		}
+ 
+ 		read_phy(lp->phy_address, MII_LPA, &lpa);
+ 		if ((lpa & LPA_100FULL) || (lpa & LPA_100HALF)) speed = SPEED_100;
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/011-vlink-resetfix.patch
@@ -1,1 +1,11 @@
+--- linux-2.6.21.1.old/arch/arm/mach-at91/board-vlink.c	2007-06-04 15:45:19.000000000 +0200
++++ linux-2.6.21.1/arch/arm/mach-at91/board-vlink.c	2007-06-05 05:27:19.000000000 +0200
+@@ -175,6 +175,7 @@
+ /* USB Device control */
+        at91_set_gpio_input(AT91_PIN_PB27, 1);  // UDB_CNX
+        at91_set_gpio_output(AT91_PIN_PB28, 1); // UDB_PUP
++			 at91_set_multi_drive(AT91_PIN_PB28, 1); // Set to multi-drive
+ 
+ }
+ 
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/012-at91-mmcfix.patch
@@ -1,1 +1,425 @@
+--- linux-2.6.21.1.old/drivers/mmc/at91_mci.c	2007-06-05 09:08:57.000000000 +0200
++++ linux-2.6.21.1/drivers/mmc/at91_mci.c	2007-06-05 10:59:11.000000000 +0200
+@@ -79,7 +79,8 @@
+ 
+ #define DRIVER_NAME "at91_mci"
+ 
+-#undef	SUPPORT_4WIRE
++//#undef	SUPPORT_4WIRE
++#define 	SUPPORT_4WIRE
+ 
+ #define FL_SENT_COMMAND	(1 << 0)
+ #define FL_SENT_STOP	(1 << 1)
+@@ -132,7 +133,7 @@
+ /*
+  * Copy from sg to a dma block - used for transfers
+  */
+-static inline void at91mci_sg_to_dma(struct at91mci_host *host, struct mmc_data *data)
++static inline void at91_mci_sg_to_dma(struct at91mci_host *host, struct mmc_data *data)
+ {
+ 	unsigned int len, i, size;
+ 	unsigned *dmabuf = host->buffer;
+@@ -181,7 +182,7 @@
+ /*
+  * Prepare a dma read
+  */
+-static void at91mci_pre_dma_read(struct at91mci_host *host)
++static void at91_mci_pre_dma_read(struct at91mci_host *host)
+ {
+ 	int i;
+ 	struct scatterlist *sg;
+@@ -249,23 +250,24 @@
+ /*
+  * Handle after a dma read
+  */
+-static void at91mci_post_dma_read(struct at91mci_host *host)
++static int at91_mci_post_dma_read(struct at91mci_host *host)
+ {
+ 	struct mmc_command *cmd;
+ 	struct mmc_data *data;
++	int completed = 0;
+ 
+ 	pr_debug("post dma read\n");
+ 
+ 	cmd = host->cmd;
+ 	if (!cmd) {
+ 		pr_debug("no command\n");
+-		return;
++		return 1;
+ 	}
+ 
+ 	data = cmd->data;
+ 	if (!data) {
+ 		pr_debug("no data\n");
+-		return;
++		return 1;
+ 	}
+ 
+ 	while (host->in_use_index < host->transfer_index) {
+@@ -300,39 +302,14 @@
+ 
+ 	/* Is there another transfer to trigger? */
+ 	if (host->transfer_index < data->sg_len)
+-		at91mci_pre_dma_read(host);
++		at91_mci_pre_dma_read(host);
+ 	else {
++		at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_ENDRX);
+ 		at91_mci_write(host, AT91_MCI_IER, AT91_MCI_RXBUFF);
+-		at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
+ 	}
+ 
+ 	pr_debug("post dma read done\n");
+-}
+-
+-/*
+- * Handle transmitted data
+- */
+-static void at91_mci_handle_transmitted(struct at91mci_host *host)
+-{
+-	struct mmc_command *cmd;
+-	struct mmc_data *data;
+-
+-	pr_debug("Handling the transmit\n");
+-
+-	/* Disable the transfer */
+-	at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
+-
+-	/* Now wait for cmd ready */
+-	at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_TXBUFE);
+-	at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY);
+-
+-	cmd = host->cmd;
+-	if (!cmd) return;
+-
+-	data = cmd->data;
+-	if (!data) return;
+-
+-	data->bytes_xfered = host->total_length;
++	return completed;
+ }
+ 
+ /*
+@@ -340,10 +317,17 @@
+  */
+ static void at91_mci_enable(struct at91mci_host *host)
+ {
++	unsigned int mr;
++
+ 	at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN);
+ 	at91_mci_write(host, AT91_MCI_IDR, 0xffffffff);
+ 	at91_mci_write(host, AT91_MCI_DTOR, AT91_MCI_DTOMUL_1M | AT91_MCI_DTOCYC);
+-	at91_mci_write(host, AT91_MCI_MR, AT91_MCI_PDCMODE | 0x34a);
++	mr = AT91_MCI_PDCMODE | 0x34a;
++
++	if (cpu_is_at91sam9260() || cpu_is_at91sam9263())
++		mr |= AT91_MCI_RDPROOF | AT91_MCI_WRPROOF;
++
++	at91_mci_write(host, AT91_MCI_MR, mr);
+ 
+ 	/* use Slot A or B (only one at same time) */
+ 	at91_mci_write(host, AT91_MCI_SDCR, host->board->slot_b);
+@@ -359,9 +343,8 @@
+ 
+ /*
+  * Send a command
+- * return the interrupts to enable
+  */
+-static unsigned int at91_mci_send_command(struct at91mci_host *host, struct mmc_command *cmd)
++static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command *cmd)
+ {
+ 	unsigned int cmdr, mr;
+ 	unsigned int block_length;
+@@ -372,8 +355,7 @@
+ 
+ 	host->cmd = cmd;
+ 
+-	/* Not sure if this is needed */
+-#if 0
++	/* Needed for leaving busy state before CMD1 */
+ 	if ((at91_mci_read(host, AT91_MCI_SR) & AT91_MCI_RTOE) && (cmd->opcode == 1)) {
+ 		pr_debug("Clearing timeout\n");
+ 		at91_mci_write(host, AT91_MCI_ARGR, 0);
+@@ -383,7 +365,7 @@
+ 			pr_debug("Clearing: SR = %08X\n", at91_mci_read(host, AT91_MCI_SR));
+ 		}
+ 	}
+-#endif
++
+ 	cmdr = cmd->opcode;
+ 
+ 	if (mmc_resp_type(cmd) == MMC_RSP_NONE)
+@@ -440,50 +422,48 @@
+ 		at91_mci_write(host, ATMEL_PDC_TCR, 0);
+ 		at91_mci_write(host, ATMEL_PDC_TNPR, 0);
+ 		at91_mci_write(host, ATMEL_PDC_TNCR, 0);
++		ier = AT91_MCI_CMDRDY;
++	} else {
++		/* zero block length in PDC mode */
++		mr = at91_mci_read(host, AT91_MCI_MR) & 0x7fff;
++		at91_mci_write(host, AT91_MCI_MR, mr | (block_length << 16) | AT91_MCI_PDCMODE);
++
++		/*
++		 * Disable the PDC controller
++		 */
++		at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
+ 
+-		at91_mci_write(host, AT91_MCI_ARGR, cmd->arg);
+-		at91_mci_write(host, AT91_MCI_CMDR, cmdr);
+-		return AT91_MCI_CMDRDY;
+-	}
+-
+-	mr = at91_mci_read(host, AT91_MCI_MR) & 0x7fff;	/* zero block length and PDC mode */
+-	at91_mci_write(host, AT91_MCI_MR, mr | (block_length << 16) | AT91_MCI_PDCMODE);
+-
+-	/*
+-	 * Disable the PDC controller
+-	 */
+-	at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
+-
+-	if (cmdr & AT91_MCI_TRCMD_START) {
+-		data->bytes_xfered = 0;
+-		host->transfer_index = 0;
+-		host->in_use_index = 0;
+-		if (cmdr & AT91_MCI_TRDIR) {
+-			/*
+-			 * Handle a read
+-			 */
+-			host->buffer = NULL;
+-			host->total_length = 0;
++		if (cmdr & AT91_MCI_TRCMD_START) {
++			data->bytes_xfered = 0;
++			host->transfer_index = 0;
++			host->in_use_index = 0;
++			if (cmdr & AT91_MCI_TRDIR) {
++				/*
++				 * Handle a read
++				 */
++				host->buffer = NULL;
++				host->total_length = 0;
+ 
+-			at91mci_pre_dma_read(host);
+-			ier = AT91_MCI_ENDRX /* | AT91_MCI_RXBUFF */;
+-		}
+-		else {
+-			/*
+-			 * Handle a write
+-			 */
+-			host->total_length = block_length * blocks;
+-			host->buffer = dma_alloc_coherent(NULL,
+-						  host->total_length,
+-						  &host->physical_address, GFP_KERNEL);
+-
+-			at91mci_sg_to_dma(host, data);
+-
+-			pr_debug("Transmitting %d bytes\n", host->total_length);
+-
+-			at91_mci_write(host, ATMEL_PDC_TPR, host->physical_address);
+-			at91_mci_write(host, ATMEL_PDC_TCR, host->total_length / 4);
+-			ier = AT91_MCI_TXBUFE;
++				at91_mci_pre_dma_read(host);
++				ier = AT91_MCI_ENDRX /* | AT91_MCI_RXBUFF */;
++			}
++			else {
++				/*
++			 	* Handle a write
++			 	*/
++				host->total_length = block_length * blocks;
++				host->buffer = dma_alloc_coherent(NULL,
++							host->total_length,
++							&host->physical_address, GFP_KERNEL);
++
++				at91_mci_sg_to_dma(host, data);
++
++				pr_debug("Transmitting %d bytes\n", host->total_length);
++
++				at91_mci_write(host, ATMEL_PDC_TPR, host->physical_address);
++				at91_mci_write(host, ATMEL_PDC_TCR, host->total_length / 4);
++				ier = AT91_MCI_CMDRDY;
++			}
+ 		}
+ 	}
+ 
+@@ -498,39 +478,24 @@
+ 	if (cmdr & AT91_MCI_TRCMD_START) {
+ 		if (cmdr & AT91_MCI_TRDIR)
+ 			at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
+-		else
+-			at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
+ 	}
+-	return ier;
+-}
+ 
+-/*
+- * Wait for a command to complete
+- */
+-static void at91mci_process_command(struct at91mci_host *host, struct mmc_command *cmd)
+-{
+-	unsigned int ier;
+-
+-	ier = at91_mci_send_command(host, cmd);
+-
+-	pr_debug("setting ier to %08X\n", ier);
+-
+-	/* Stop on errors or the required value */
++	/* Enable selected interrupts */
+ 	at91_mci_write(host, AT91_MCI_IER, AT91_MCI_ERRORS | ier);
+ }
+ 
+ /*
+  * Process the next step in the request
+  */
+-static void at91mci_process_next(struct at91mci_host *host)
++static void at91_mci_process_next(struct at91mci_host *host)
+ {
+ 	if (!(host->flags & FL_SENT_COMMAND)) {
+ 		host->flags |= FL_SENT_COMMAND;
+-		at91mci_process_command(host, host->request->cmd);
++		at91_mci_send_command(host, host->request->cmd);
+ 	}
+ 	else if ((!(host->flags & FL_SENT_STOP)) && host->request->stop) {
+ 		host->flags |= FL_SENT_STOP;
+-		at91mci_process_command(host, host->request->stop);
++		at91_mci_send_command(host, host->request->stop);
+ 	}
+ 	else
+ 		mmc_request_done(host->mmc, host->request);
+@@ -539,7 +504,7 @@
+ /*
+  * Handle a command that has been completed
+  */
+-static void at91mci_completed_command(struct at91mci_host *host)
++static void at91_mci_completed_command(struct at91mci_host *host)
+ {
+ 	struct mmc_command *cmd = host->cmd;
+ 	unsigned int status;
+@@ -583,7 +548,7 @@
+ 	else
+ 		cmd->error = MMC_ERR_NONE;
+ 
+-	at91mci_process_next(host);
++	at91_mci_process_next(host);
+ }
+ 
+ /*
+@@ -595,7 +560,60 @@
+ 	host->request = mrq;
+ 	host->flags = 0;
+ 
+-	at91mci_process_next(host);
++	at91_mci_process_next(host);
++}
++
++/*
++ * Handle transmitted data
++ */
++static void at91_mci_handle_transmitted(struct at91mci_host *host)
++{
++	struct mmc_command *cmd;
++	struct mmc_data *data;
++
++	pr_debug("Handling the transmit\n");
++
++	/* Disable the transfer */
++	at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
++
++	/* Now wait for cmd ready */
++	at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_TXBUFE);
++
++	cmd = host->cmd;
++	if (!cmd) return;
++
++	data = cmd->data;
++	if (!data) return;
++
++	if (cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK) {
++		pr_debug("multiple write : wait for BLKE...\n");
++		at91_mci_write(host, AT91_MCI_IER, AT91_MCI_BLKE);
++	} else
++		at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY);
++
++	data->bytes_xfered = host->total_length;
++}
++
++
++/*Handle after command sent ready*/
++static int at91_mci_handle_cmdrdy(struct at91mci_host *host)
++{
++	if (!host->cmd)
++		return 1;
++	else if (!host->cmd->data) {
++		if (host->flags & FL_SENT_STOP) {
++			/*After multi block write, we mus wait for NOTBUSY*/
++			at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY);
++		} else return 1;
++	} else if (host->cmd->data->flags & MMC_DATA_WRITE) {
++		/*After sending multi-block-write command, start DMA transfer*/
++		at91_mci_write(host, AT91_MCI_IER, AT91_MCI_TXBUFE);
++		at91_mci_write(host, AT91_MCI_IER, AT91_MCI_BLKE);
++		at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
++	}
++
++	/* command not completed, have to wait */
++	return 0;
+ }
+ 
+ /*
+@@ -698,29 +716,33 @@
+ 			at91_mci_handle_transmitted(host);
+ 		}
+ 
++		if (int_status & AT91_MCI_ENDRX) {
++			pr_debug("ENDRX\n");
++			at91_mci_post_dma_read(host);
++		}
++
+ 		if (int_status & AT91_MCI_RXBUFF) {
+ 			pr_debug("RX buffer full\n");
+-			at91_mci_write(host, AT91_MCI_IER, AT91_MCI_CMDRDY);
++			at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
++			at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_RXBUFF | AT91_MCI_ENDRX);
++			completed = 1;
+ 		}
+ 
+ 		if (int_status & AT91_MCI_ENDTX)
+ 			pr_debug("Transmit has ended\n");
+ 
+-		if (int_status & AT91_MCI_ENDRX) {
+-			pr_debug("Receive has ended\n");
+-			at91mci_post_dma_read(host);
+-		}
+-
+ 		if (int_status & AT91_MCI_NOTBUSY) {
+ 			pr_debug("Card is ready\n");
+-			at91_mci_write(host, AT91_MCI_IER, AT91_MCI_CMDRDY);
++			completed = 1;
+ 		}
+ 
+ 		if (int_status & AT91_MCI_DTIP)
+ 			pr_debug("Data transfer in progress\n");
+ 
+-		if (int_status & AT91_MCI_BLKE)
++		if (int_status & AT91_MCI_BLKE) {
+ 			pr_debug("Block transfer has ended\n");
++			completed = 1;
++		}
+ 
+ 		if (int_status & AT91_MCI_TXRDY)
+ 			pr_debug("Ready to transmit\n");
+@@ -730,14 +752,14 @@
+ 
+ 		if (int_status & AT91_MCI_CMDRDY) {
+ 			pr_debug("Command ready\n");
+-			completed = 1;
++			completed = at91_mci_handle_cmdrdy(host);
+ 		}
+ 	}
+ 
+ 	if (completed) {
+ 		pr_debug("Completed command\n");
+ 		at91_mci_write(host, AT91_MCI_IDR, 0xffffffff);
+-		at91mci_completed_command(host);
++		at91_mci_completed_command(host);
+ 	} else
+ 		at91_mci_write(host, AT91_MCI_IDR, int_status);
+ 
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/013-at91-mmc1wire.patch
@@ -1,1 +1,13 @@
+--- linux-2.6.21.1.old/drivers/mmc/at91_mci.c	2007-06-05 11:08:39.000000000 +0200
++++ linux-2.6.21.1/drivers/mmc/at91_mci.c	2007-06-05 11:28:40.000000000 +0200
+@@ -79,8 +79,7 @@
+ 
+ #define DRIVER_NAME "at91_mci"
+ 
+-//#undef	SUPPORT_4WIRE
+-#define 	SUPPORT_4WIRE
++#undef	SUPPORT_4WIRE
+ 
+ #define FL_SENT_COMMAND	(1 << 0)
+ #define FL_SENT_STOP	(1 << 1)
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.21/014-initpartition.patch
@@ -1,1 +1,19 @@
+--- linux-2.6.21.5.old/drivers/mtd/devices/at91_dataflash.c	2007-06-13 13:31:24.000000000 +0200
++++ linux-2.6.21.5/drivers/mtd/devices/at91_dataflash.c	2007-06-19 12:49:48.000000000 +0200
+@@ -161,12 +161,12 @@
+ 		.mask_flags	= MTD_WRITEABLE,	/* read-only */
+ 	},
+ 	{
+-		.name		= "kernel",
++		.name		= "knlroot",
+ 		.offset		= MTDPART_OFS_NXTBLK,
+-		.size		= 5 * 32 * 8 * 1056,	/* 5 sectors */
++		.size		= 0x320400,	/* 5 sectors */
+ 	},
+ 	{
+-		.name		= "filesystem",
++		.name		= "jffs2",
+ 		.offset		= MTDPART_OFS_NXTBLK,
+ 		.size		= MTDPART_SIZ_FULL,	/* rest = 26 sectors */
+ 	}
 

--- /dev/null
+++ b/target/linux/at91-2.6/patches-2.6.22/000-at91.patch
@@ -1,1 +1,9933 @@
+diff -urN linux-2.6.22-rc5/arch/arm/boot/compressed/head-at91rm9200.S linux-2.6.22-rc5.new/arch/arm/boot/compressed/head-at91rm9200.S
+--- linux-2.6.22-rc5/arch/arm/boot/compressed/head-at91rm9200.S	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/boot/compressed/head-at91rm9200.S	2007-07-29 05:23:04.000000000 +0200
+@@ -73,6 +73,12 @@
+ 		cmp	r7, r3
+ 		beq	99f
+ 
++		@ Promwad Chub : 1181
++		mov	r3,	#(MACH_TYPE_CHUB & 0xff)
++		orr	r3, r3, #(MACH_TYPE_CHUB & 0xff00)
++		cmp	r7, r3
++		beq	99f
++
+ 		@ Unknown board, use the AT91RM9200DK board
+ 		@ mov	r7, #MACH_TYPE_AT91RM9200
+ 		mov	r7,	#(MACH_TYPE_AT91RM9200DK & 0xff)
+diff -urN linux-2.6.22-rc5/arch/arm/configs/at91sam9260ek_defconfig linux-2.6.22-rc5.new/arch/arm/configs/at91sam9260ek_defconfig
+--- linux-2.6.22-rc5/arch/arm/configs/at91sam9260ek_defconfig	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/configs/at91sam9260ek_defconfig	2007-07-29 05:23:04.000000000 +0200
+@@ -1,18 +1,24 @@
+ #
+ # Automatically generated make config: don't edit
+-# Linux kernel version: 2.6.19-rc6
+-# Fri Nov 17 18:42:21 2006
++# Linux kernel version: 2.6.21
++# Mon May  7 11:42:02 2007
+ #
+ CONFIG_ARM=y
++CONFIG_SYS_SUPPORTS_APM_EMULATION=y
++CONFIG_GENERIC_GPIO=y
+ # CONFIG_GENERIC_TIME is not set
+ CONFIG_MMU=y
++# CONFIG_NO_IOPORT is not set
+ CONFIG_GENERIC_HARDIRQS=y
+ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+ CONFIG_HARDIRQS_SW_RESEND=y
+ CONFIG_GENERIC_IRQ_PROBE=y
+ CONFIG_RWSEM_GENERIC_SPINLOCK=y
++# CONFIG_ARCH_HAS_ILOG2_U32 is not set
++# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+ CONFIG_GENERIC_HWEIGHT=y
+ CONFIG_GENERIC_CALIBRATE_DELAY=y
++CONFIG_ZONE_DMA=y
+ CONFIG_VECTORS_BASE=0xffff0000
+ CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+ 
+@@ -31,13 +37,16 @@
+ # CONFIG_SWAP is not set
+ CONFIG_SYSVIPC=y
+ # CONFIG_IPC_NS is not set
++CONFIG_SYSVIPC_SYSCTL=y
+ # CONFIG_POSIX_MQUEUE is not set
+ # CONFIG_BSD_PROCESS_ACCT is not set
+ # CONFIG_TASKSTATS is not set
+ # CONFIG_UTS_NS is not set
+ # CONFIG_AUDIT is not set
+ # CONFIG_IKCONFIG is not set
++CONFIG_SYSFS_DEPRECATED=y
+ # CONFIG_RELAY is not set
++CONFIG_BLK_DEV_INITRD=y
+ CONFIG_INITRAMFS_SOURCE=""
+ CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+ CONFIG_SYSCTL=y
+@@ -76,7 +85,9 @@
+ # Block layer
+ #
+ CONFIG_BLOCK=y
++# CONFIG_LBD is not set
+ # CONFIG_BLK_DEV_IO_TRACE is not set
++# CONFIG_LSF is not set
+ 
+ #
+ # IO Schedulers
+@@ -110,10 +121,12 @@
+ # CONFIG_ARCH_IMX is not set
+ # CONFIG_ARCH_IOP32X is not set
+ # CONFIG_ARCH_IOP33X is not set
++# CONFIG_ARCH_IOP13XX is not set
+ # CONFIG_ARCH_IXP4XX is not set
+ # CONFIG_ARCH_IXP2000 is not set
+ # CONFIG_ARCH_IXP23XX is not set
+ # CONFIG_ARCH_L7200 is not set
++# CONFIG_ARCH_NS9XXX is not set
+ # CONFIG_ARCH_PNX4008 is not set
+ # CONFIG_ARCH_PXA is not set
+ # CONFIG_ARCH_RPC is not set
+@@ -129,21 +142,29 @@
+ # CONFIG_ARCH_AT91RM9200 is not set
+ CONFIG_ARCH_AT91SAM9260=y
+ # CONFIG_ARCH_AT91SAM9261 is not set
++# CONFIG_ARCH_AT91SAM9263 is not set
++
++#
++# AT91SAM9260 Variants
++#
++# CONFIG_ARCH_AT91SAM9260_SAM9XE is not set
+ 
+ #
+-# AT91SAM9260 Board Type
++# AT91SAM9260 / AT91SAM9XE Board Type
+ #
+ CONFIG_MACH_AT91SAM9260EK=y
+ 
+ #
+ # AT91 Board Options
+ #
++# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
+ # CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+ 
+ #
+ # AT91 Feature Selections
+ #
+ # CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
++# CONFIG_ATMEL_TCLIB is not set
+ 
+ #
+ # Processor Type
+@@ -166,6 +187,7 @@
+ # CONFIG_CPU_DCACHE_DISABLE is not set
+ # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+ # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
++# CONFIG_OUTER_CACHE is not set
+ 
+ #
+ # Bus support
+@@ -193,6 +215,7 @@
+ # CONFIG_SPARSEMEM_STATIC is not set
+ CONFIG_SPLIT_PTLOCK_CPUS=4096
+ # CONFIG_RESOURCES_64BIT is not set
++CONFIG_ZONE_DMA_FLAG=1
+ # CONFIG_LEDS is not set
+ CONFIG_ALIGNMENT_TRAP=y
+ 
+@@ -203,6 +226,7 @@
+ CONFIG_ZBOOT_ROM_BSS=0x0
+ CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
+ # CONFIG_XIP_KERNEL is not set
++# CONFIG_KEXEC is not set
+ 
+ #
+ # Floating point emulation
+@@ -228,7 +252,6 @@
+ # Power management options
+ #
+ # CONFIG_PM is not set
+-# CONFIG_APM is not set
+ 
+ #
+ # Networking
+@@ -242,9 +265,6 @@
+ CONFIG_PACKET=y
+ # CONFIG_PACKET_MMAP is not set
+ CONFIG_UNIX=y
+-CONFIG_XFRM=y
+-# CONFIG_XFRM_USER is not set
+-# CONFIG_XFRM_SUB_POLICY is not set
+ # CONFIG_NET_KEY is not set
+ CONFIG_INET=y
+ # CONFIG_IP_MULTICAST is not set
+@@ -263,14 +283,15 @@
+ # CONFIG_INET_IPCOMP is not set
+ # CONFIG_INET_XFRM_TUNNEL is not set
+ # CONFIG_INET_TUNNEL is not set
+-CONFIG_INET_XFRM_MODE_TRANSPORT=y
+-CONFIG_INET_XFRM_MODE_TUNNEL=y
+-CONFIG_INET_XFRM_MODE_BEET=y
++# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
++# CONFIG_INET_XFRM_MODE_TUNNEL is not set
++# CONFIG_INET_XFRM_MODE_BEET is not set
+ CONFIG_INET_DIAG=y
+ CONFIG_INET_TCP_DIAG=y
+ # CONFIG_TCP_CONG_ADVANCED is not set
+ CONFIG_TCP_CONG_CUBIC=y
+ CONFIG_DEFAULT_TCP_CONG="cubic"
++# CONFIG_TCP_MD5SIG is not set
+ # CONFIG_IPV6 is not set
+ # CONFIG_INET6_XFRM_TUNNEL is not set
+ # CONFIG_INET6_TUNNEL is not set
+@@ -328,6 +349,7 @@
+ CONFIG_PREVENT_FIRMWARE_BUILD=y
+ # CONFIG_FW_LOADER is not set
+ # CONFIG_DEBUG_DRIVER is not set
++# CONFIG_DEBUG_DEVRES is not set
+ # CONFIG_SYS_HYPERVISOR is not set
+ 
+ #
+@@ -348,6 +370,7 @@
+ #
+ # Plug and Play support
+ #
++# CONFIG_PNPACPI is not set
+ 
+ #
+ # Block devices
+@@ -360,7 +383,6 @@
+ CONFIG_BLK_DEV_RAM_COUNT=16
+ CONFIG_BLK_DEV_RAM_SIZE=8192
+ CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+-CONFIG_BLK_DEV_INITRD=y
+ # CONFIG_CDROM_PKTCDVD is not set
+ # CONFIG_ATA_OVER_ETH is not set
+ 
+@@ -369,6 +391,7 @@
+ #
+ # CONFIG_RAID_ATTRS is not set
+ CONFIG_SCSI=y
++# CONFIG_SCSI_TGT is not set
+ # CONFIG_SCSI_NETLINK is not set
+ CONFIG_SCSI_PROC_FS=y
+ 
+@@ -388,6 +411,7 @@
+ CONFIG_SCSI_MULTI_LUN=y
+ # CONFIG_SCSI_CONSTANTS is not set
+ # CONFIG_SCSI_LOGGING is not set
++# CONFIG_SCSI_SCAN_ASYNC is not set
+ 
+ #
+ # SCSI Transports
+@@ -405,6 +429,11 @@
+ # CONFIG_SCSI_DEBUG is not set
+ 
+ #
++# Serial ATA (prod) and Parallel ATA (experimental) drivers
++#
++# CONFIG_ATA is not set
++
++#
+ # Multi-device support (RAID and LVM)
+ #
+ # CONFIG_MD is not set
+@@ -425,7 +454,51 @@
+ #
+ # Network device support
+ #
+-# CONFIG_NETDEVICES is not set
++CONFIG_NETDEVICES=y
++# CONFIG_DUMMY is not set
++# CONFIG_BONDING is not set
++# CONFIG_EQUALIZER is not set
++# CONFIG_TUN is not set
++
++#
++# PHY device support
++#
++# CONFIG_PHYLIB is not set
++
++#
++# Ethernet (10 or 100Mbit)
++#
++CONFIG_NET_ETHERNET=y
++CONFIG_MII=y
++CONFIG_MACB=y
++# CONFIG_SMC91X is not set
++# CONFIG_DM9000 is not set
++
++#
++# Ethernet (1000 Mbit)
++#
++
++#
++# Ethernet (10000 Mbit)
++#
++
++#
++# Token Ring devices
++#
++
++#
++# Wireless LAN (non-hamradio)
++#
++# CONFIG_NET_RADIO is not set
++
++#
++# Wan interfaces
++#
++# CONFIG_WAN is not set
++# CONFIG_PPP is not set
++# CONFIG_SLIP is not set
++# CONFIG_SHAPER is not set
++# CONFIG_NETCONSOLE is not set
+ # CONFIG_NETPOLL is not set
+ # CONFIG_NET_POLL_CONTROLLER is not set
+ 
+@@ -517,10 +590,6 @@
+ # CONFIG_NVRAM is not set
+ # CONFIG_DTLK is not set
+ # CONFIG_R3964 is not set
+-
+-#
+-# Ftape, the floppy tape device driver
+-#
+ # CONFIG_RAW_DRIVER is not set
+ 
+ #
+@@ -553,7 +622,11 @@
+ #
+ # Misc devices
+ #
+-# CONFIG_TIFM_CORE is not set
++
++#
++# Multifunction device drivers
++#
++# CONFIG_MFD_SM501 is not set
+ 
+ #
+ # LED devices
+@@ -582,7 +655,7 @@
+ #
+ # Graphics support
+ #
+-# CONFIG_FIRMWARE_EDID is not set
++# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+ # CONFIG_FB is not set
+ 
+ #
+@@ -590,7 +663,6 @@
+ #
+ # CONFIG_VGA_CONSOLE is not set
+ CONFIG_DUMMY_CONSOLE=y
+-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+ 
+ #
+ # Sound
+@@ -598,6 +670,12 @@
+ # CONFIG_SOUND is not set
+ 
+ #
++# HID Devices
++#
++CONFIG_HID=y
++# CONFIG_HID_DEBUG is not set
++
++#
+ # USB support
+ #
+ CONFIG_USB_ARCH_HAS_HCD=y
+@@ -610,7 +688,6 @@
+ # Miscellaneous USB options
+ #
+ CONFIG_USB_DEVICEFS=y
+-# CONFIG_USB_BANDWIDTH is not set
+ # CONFIG_USB_DYNAMIC_MINORS is not set
+ # CONFIG_USB_OTG is not set
+ 
+@@ -619,7 +696,8 @@
+ #
+ # CONFIG_USB_ISP116X_HCD is not set
+ CONFIG_USB_OHCI_HCD=y
+-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
++# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
++# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+ CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+ # CONFIG_USB_SL811_HCD is not set
+ 
+@@ -671,6 +749,7 @@
+ # CONFIG_USB_ATI_REMOTE2 is not set
+ # CONFIG_USB_KEYSPAN_REMOTE is not set
+ # CONFIG_USB_APPLETOUCH is not set
++# CONFIG_USB_GTCO is not set
+ 
+ #
+ # USB Imaging devices
+@@ -708,6 +787,7 @@
+ # CONFIG_USB_RIO500 is not set
+ # CONFIG_USB_LEGOTOWER is not set
+ # CONFIG_USB_LCD is not set
++# CONFIG_USB_BERRY_CHARGE is not set
+ # CONFIG_USB_LED is not set
+ # CONFIG_USB_CYPRESS_CY7C63 is not set
+ # CONFIG_USB_CYTHERM is not set
+@@ -717,6 +797,7 @@
+ # CONFIG_USB_APPLEDISPLAY is not set
+ # CONFIG_USB_LD is not set
+ # CONFIG_USB_TRANCEVIBRATOR is not set
++# CONFIG_USB_IOWARRIOR is not set
+ # CONFIG_USB_TEST is not set
+ 
+ #
+@@ -889,6 +970,11 @@
+ # CONFIG_NLS_UTF8 is not set
+ 
+ #
++# Distributed Lock Manager
++#
++# CONFIG_DLM is not set
++
++#
+ # Profiling support
+ #
+ # CONFIG_PROFILING is not set
+@@ -900,28 +986,30 @@
+ CONFIG_ENABLE_MUST_CHECK=y
+ # CONFIG_MAGIC_SYSRQ is not set
+ # CONFIG_UNUSED_SYMBOLS is not set
++# CONFIG_DEBUG_FS is not set
++# CONFIG_HEADERS_CHECK is not set
+ CONFIG_DEBUG_KERNEL=y
++# CONFIG_DEBUG_SHIRQ is not set
+ CONFIG_LOG_BUF_SHIFT=14
+ CONFIG_DETECT_SOFTLOCKUP=y
+ # CONFIG_SCHEDSTATS is not set
++# CONFIG_TIMER_STATS is not set
+ # CONFIG_DEBUG_SLAB is not set
+ # CONFIG_DEBUG_RT_MUTEXES is not set
+ # CONFIG_RT_MUTEX_TESTER is not set
+ # CONFIG_DEBUG_SPINLOCK is not set
+ # CONFIG_DEBUG_MUTEXES is not set
+-# CONFIG_DEBUG_RWSEMS is not set
+ # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+ # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+ # CONFIG_DEBUG_KOBJECT is not set
+ CONFIG_DEBUG_BUGVERBOSE=y
+ # CONFIG_DEBUG_INFO is not set
+-# CONFIG_DEBUG_FS is not set
+ # CONFIG_DEBUG_VM is not set
+ # CONFIG_DEBUG_LIST is not set
+ CONFIG_FRAME_POINTER=y
+ CONFIG_FORCED_INLINING=y
+-# CONFIG_HEADERS_CHECK is not set
+ # CONFIG_RCU_TORTURE_TEST is not set
++# CONFIG_FAULT_INJECTION is not set
+ CONFIG_DEBUG_USER=y
+ # CONFIG_DEBUG_ERRORS is not set
+ CONFIG_DEBUG_LL=y
+@@ -941,9 +1029,12 @@
+ #
+ # Library routines
+ #
++CONFIG_BITREVERSE=y
+ # CONFIG_CRC_CCITT is not set
+ # CONFIG_CRC16 is not set
+ CONFIG_CRC32=y
+ # CONFIG_LIBCRC32C is not set
+ CONFIG_ZLIB_INFLATE=y
+ CONFIG_PLIST=y
++CONFIG_HAS_IOMEM=y
++CONFIG_HAS_IOPORT=y
+diff -urN linux-2.6.22-rc5/arch/arm/configs/at91sam9261ek_defconfig linux-2.6.22-rc5.new/arch/arm/configs/at91sam9261ek_defconfig
+--- linux-2.6.22-rc5/arch/arm/configs/at91sam9261ek_defconfig	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/configs/at91sam9261ek_defconfig	2007-07-29 05:23:04.000000000 +0200
+@@ -1,18 +1,24 @@
+ #
+ # Automatically generated make config: don't edit
+-# Linux kernel version: 2.6.19-rc6
+-# Fri Nov 17 18:00:38 2006
++# Linux kernel version: 2.6.21
++# Mon May  7 11:42:30 2007
+ #
+ CONFIG_ARM=y
++CONFIG_SYS_SUPPORTS_APM_EMULATION=y
++CONFIG_GENERIC_GPIO=y
+ # CONFIG_GENERIC_TIME is not set
+ CONFIG_MMU=y
++# CONFIG_NO_IOPORT is not set
+ CONFIG_GENERIC_HARDIRQS=y
+ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+ CONFIG_HARDIRQS_SW_RESEND=y
+ CONFIG_GENERIC_IRQ_PROBE=y
+ CONFIG_RWSEM_GENERIC_SPINLOCK=y
++# CONFIG_ARCH_HAS_ILOG2_U32 is not set
++# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+ CONFIG_GENERIC_HWEIGHT=y
+ CONFIG_GENERIC_CALIBRATE_DELAY=y
++CONFIG_ZONE_DMA=y
+ CONFIG_VECTORS_BASE=0xffff0000
+ CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+ 
+@@ -31,13 +37,16 @@
+ # CONFIG_SWAP is not set
+ CONFIG_SYSVIPC=y
+ # CONFIG_IPC_NS is not set
++CONFIG_SYSVIPC_SYSCTL=y
+ # CONFIG_POSIX_MQUEUE is not set
+ # CONFIG_BSD_PROCESS_ACCT is not set
+ # CONFIG_TASKSTATS is not set
+ # CONFIG_UTS_NS is not set
+ # CONFIG_AUDIT is not set
+ # CONFIG_IKCONFIG is not set
++CONFIG_SYSFS_DEPRECATED=y
+ # CONFIG_RELAY is not set
++CONFIG_BLK_DEV_INITRD=y
+ CONFIG_INITRAMFS_SOURCE=""
+ CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+ CONFIG_SYSCTL=y
+@@ -76,7 +85,9 @@
+ # Block layer
+ #
+ CONFIG_BLOCK=y
++# CONFIG_LBD is not set
+ # CONFIG_BLK_DEV_IO_TRACE is not set
++# CONFIG_LSF is not set
+ 
+ #
+ # IO Schedulers
+@@ -110,10 +121,12 @@
+ # CONFIG_ARCH_IMX is not set
+ # CONFIG_ARCH_IOP32X is not set
+ # CONFIG_ARCH_IOP33X is not set
++# CONFIG_ARCH_IOP13XX is not set
+ # CONFIG_ARCH_IXP4XX is not set
+ # CONFIG_ARCH_IXP2000 is not set
+ # CONFIG_ARCH_IXP23XX is not set
+ # CONFIG_ARCH_L7200 is not set
++# CONFIG_ARCH_NS9XXX is not set
+ # CONFIG_ARCH_PNX4008 is not set
+ # CONFIG_ARCH_PXA is not set
+ # CONFIG_ARCH_RPC is not set
+@@ -129,6 +142,7 @@
+ # CONFIG_ARCH_AT91RM9200 is not set
+ # CONFIG_ARCH_AT91SAM9260 is not set
+ CONFIG_ARCH_AT91SAM9261=y
++# CONFIG_ARCH_AT91SAM9263 is not set
+ 
+ #
+ # AT91SAM9261 Board Type
+@@ -138,12 +152,14 @@
+ #
+ # AT91 Board Options
+ #
++# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
+ # CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+ 
+ #
+ # AT91 Feature Selections
+ #
+ # CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
++# CONFIG_ATMEL_TCLIB is not set
+ 
+ #
+ # Processor Type
+@@ -166,6 +182,7 @@
+ # CONFIG_CPU_DCACHE_DISABLE is not set
+ # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+ # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
++# CONFIG_OUTER_CACHE is not set
+ 
+ #
+ # Bus support
+@@ -193,6 +210,7 @@
+ # CONFIG_SPARSEMEM_STATIC is not set
+ CONFIG_SPLIT_PTLOCK_CPUS=4096
+ # CONFIG_RESOURCES_64BIT is not set
++CONFIG_ZONE_DMA_FLAG=1
+ # CONFIG_LEDS is not set
+ CONFIG_ALIGNMENT_TRAP=y
+ 
+@@ -203,6 +221,7 @@
+ CONFIG_ZBOOT_ROM_BSS=0x0
+ CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
+ # CONFIG_XIP_KERNEL is not set
++# CONFIG_KEXEC is not set
+ 
+ #
+ # Floating point emulation
+@@ -228,7 +247,6 @@
+ # Power management options
+ #
+ # CONFIG_PM is not set
+-# CONFIG_APM is not set
+ 
+ #
+ # Networking
+@@ -245,6 +263,7 @@
+ CONFIG_XFRM=y
+ # CONFIG_XFRM_USER is not set
+ # CONFIG_XFRM_SUB_POLICY is not set
++# CONFIG_XFRM_MIGRATE is not set
+ # CONFIG_NET_KEY is not set
+ CONFIG_INET=y
+ # CONFIG_IP_MULTICAST is not set
+@@ -271,6 +290,7 @@
+ # CONFIG_TCP_CONG_ADVANCED is not set
+ CONFIG_TCP_CONG_CUBIC=y
+ CONFIG_DEFAULT_TCP_CONG="cubic"
++# CONFIG_TCP_MD5SIG is not set
+ # CONFIG_IPV6 is not set
+ # CONFIG_INET6_XFRM_TUNNEL is not set
+ # CONFIG_INET6_TUNNEL is not set
+@@ -328,6 +348,7 @@
+ CONFIG_PREVENT_FIRMWARE_BUILD=y
+ # CONFIG_FW_LOADER is not set
+ # CONFIG_DEBUG_DRIVER is not set
++# CONFIG_DEBUG_DEVRES is not set
+ # CONFIG_SYS_HYPERVISOR is not set
+ 
+ #
+@@ -350,6 +371,7 @@
+ # User Modules And Translation Layers
+ #
+ # CONFIG_MTD_CHAR is not set
++CONFIG_MTD_BLKDEVS=y
+ CONFIG_MTD_BLOCK=y
+ # CONFIG_FTL is not set
+ # CONFIG_NFTL is not set
+@@ -386,6 +408,8 @@
+ #
+ # Self-contained MTD device drivers
+ #
++# CONFIG_MTD_DATAFLASH is not set
++# CONFIG_MTD_M25P80 is not set
+ # CONFIG_MTD_SLRAM is not set
+ # CONFIG_MTD_PHRAM is not set
+ # CONFIG_MTD_MTDRAM is not set
+@@ -422,6 +446,7 @@
+ #
+ # Plug and Play support
+ #
++# CONFIG_PNPACPI is not set
+ 
+ #
+ # Block devices
+@@ -434,7 +459,6 @@
+ CONFIG_BLK_DEV_RAM_COUNT=16
+ CONFIG_BLK_DEV_RAM_SIZE=8192
+ CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+-CONFIG_BLK_DEV_INITRD=y
+ # CONFIG_CDROM_PKTCDVD is not set
+ # CONFIG_ATA_OVER_ETH is not set
+ 
+@@ -443,6 +467,7 @@
+ #
+ # CONFIG_RAID_ATTRS is not set
+ CONFIG_SCSI=y
++# CONFIG_SCSI_TGT is not set
+ # CONFIG_SCSI_NETLINK is not set
+ CONFIG_SCSI_PROC_FS=y
+ 
+@@ -462,6 +487,7 @@
+ CONFIG_SCSI_MULTI_LUN=y
+ # CONFIG_SCSI_CONSTANTS is not set
+ # CONFIG_SCSI_LOGGING is not set
++# CONFIG_SCSI_SCAN_ASYNC is not set
+ 
+ #
+ # SCSI Transports
+@@ -479,6 +505,11 @@
+ # CONFIG_SCSI_DEBUG is not set
+ 
+ #
++# Serial ATA (prod) and Parallel ATA (experimental) drivers
++#
++# CONFIG_ATA is not set
++
++#
+ # Multi-device support (RAID and LVM)
+ #
+ # CONFIG_MD is not set
+@@ -575,7 +606,16 @@
+ # CONFIG_INPUT_KEYBOARD is not set
+ # CONFIG_INPUT_MOUSE is not set
+ # CONFIG_INPUT_JOYSTICK is not set
+-# CONFIG_INPUT_TOUCHSCREEN is not set
++CONFIG_INPUT_TOUCHSCREEN=y
++CONFIG_TOUCHSCREEN_ADS7846=y
++# CONFIG_TOUCHSCREEN_GUNZE is not set
++# CONFIG_TOUCHSCREEN_ELO is not set
++# CONFIG_TOUCHSCREEN_MTOUCH is not set
++# CONFIG_TOUCHSCREEN_MK712 is not set
++# CONFIG_TOUCHSCREEN_PENMOUNT is not set
++# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
++# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
++# CONFIG_TOUCHSCREEN_UCB1400 is not set
+ # CONFIG_INPUT_MISC is not set
+ 
+ #
+@@ -634,10 +674,6 @@
+ # CONFIG_NVRAM is not set
+ # CONFIG_DTLK is not set
+ # CONFIG_R3964 is not set
+-
+-#
+-# Ftape, the floppy tape device driver
+-#
+ # CONFIG_RAW_DRIVER is not set
+ 
+ #
+@@ -662,6 +698,7 @@
+ # I2C Hardware Bus support
+ #
+ CONFIG_I2C_AT91=y
++CONFIG_I2C_AT91_CLOCKRATE=100000
+ # CONFIG_I2C_OCORES is not set
+ # CONFIG_I2C_PARPORT_LIGHT is not set
+ # CONFIG_I2C_STUB is not set
+@@ -686,8 +723,20 @@
+ #
+ # SPI support
+ #
+-# CONFIG_SPI is not set
+-# CONFIG_SPI_MASTER is not set
++CONFIG_SPI=y
++# CONFIG_SPI_DEBUG is not set
++CONFIG_SPI_MASTER=y
++
++#
++# SPI Master Controller Drivers
++#
++CONFIG_SPI_ATMEL=y
++# CONFIG_SPI_BITBANG is not set
++
++#
++# SPI Protocol Masters
++#
++# CONFIG_SPI_AT25 is not set
+ 
+ #
+ # Dallas's 1-wire bus
+@@ -703,7 +752,11 @@
+ #
+ # Misc devices
+ #
+-# CONFIG_TIFM_CORE is not set
++
++#
++# Multifunction device drivers
++#
++# CONFIG_MFD_SM501 is not set
+ 
+ #
+ # LED devices
+@@ -732,7 +785,7 @@
+ #
+ # Graphics support
+ #
+-# CONFIG_FIRMWARE_EDID is not set
++# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+ # CONFIG_FB is not set
+ 
+ #
+@@ -740,7 +793,6 @@
+ #
+ # CONFIG_VGA_CONSOLE is not set
+ CONFIG_DUMMY_CONSOLE=y
+-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+ 
+ #
+ # Sound
+@@ -748,6 +800,12 @@
+ # CONFIG_SOUND is not set
+ 
+ #
++# HID Devices
++#
++CONFIG_HID=y
++# CONFIG_HID_DEBUG is not set
++
++#
+ # USB support
+ #
+ CONFIG_USB_ARCH_HAS_HCD=y
+@@ -760,7 +818,6 @@
+ # Miscellaneous USB options
+ #
+ CONFIG_USB_DEVICEFS=y
+-# CONFIG_USB_BANDWIDTH is not set
+ # CONFIG_USB_DYNAMIC_MINORS is not set
+ # CONFIG_USB_OTG is not set
+ 
+@@ -769,7 +826,8 @@
+ #
+ # CONFIG_USB_ISP116X_HCD is not set
+ CONFIG_USB_OHCI_HCD=y
+-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
++# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
++# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+ CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+ # CONFIG_USB_SL811_HCD is not set
+ 
+@@ -821,6 +879,7 @@
+ # CONFIG_USB_ATI_REMOTE2 is not set
+ # CONFIG_USB_KEYSPAN_REMOTE is not set
+ # CONFIG_USB_APPLETOUCH is not set
++# CONFIG_USB_GTCO is not set
+ 
+ #
+ # USB Imaging devices
+@@ -858,6 +917,7 @@
+ # CONFIG_USB_RIO500 is not set
+ # CONFIG_USB_LEGOTOWER is not set
+ # CONFIG_USB_LCD is not set
++# CONFIG_USB_BERRY_CHARGE is not set
+ # CONFIG_USB_LED is not set
+ # CONFIG_USB_CYPRESS_CY7C63 is not set
+ # CONFIG_USB_CYTHERM is not set
+@@ -867,6 +927,7 @@
+ # CONFIG_USB_APPLEDISPLAY is not set
+ # CONFIG_USB_LD is not set
+ # CONFIG_USB_TRANCEVIBRATOR is not set
++# CONFIG_USB_IOWARRIOR is not set
+ # CONFIG_USB_TEST is not set
+ 
+ #
+@@ -903,7 +964,6 @@
+ # CONFIG_MMC_DEBUG is not set
+ CONFIG_MMC_BLOCK=y
+ CONFIG_MMC_AT91=m
+-# CONFIG_MMC_TIFM_SD is not set
+ 
+ #
+ # Real Time Clock
+@@ -973,7 +1033,6 @@
+ # CONFIG_BEFS_FS is not set
+ # CONFIG_BFS_FS is not set
+ # CONFIG_EFS_FS is not set
+-# CONFIG_JFFS_FS is not set
+ # CONFIG_JFFS2_FS is not set
+ CONFIG_CRAMFS=y
+ # CONFIG_VXFS_FS is not set
+@@ -1045,6 +1104,11 @@
+ # CONFIG_NLS_UTF8 is not set
+ 
+ #
++# Distributed Lock Manager
++#
++# CONFIG_DLM is not set
++
++#
+ # Profiling support
+ #
+ # CONFIG_PROFILING is not set
+@@ -1056,28 +1120,30 @@
+ CONFIG_ENABLE_MUST_CHECK=y
+ # CONFIG_MAGIC_SYSRQ is not set
+ # CONFIG_UNUSED_SYMBOLS is not set
++# CONFIG_DEBUG_FS is not set
++# CONFIG_HEADERS_CHECK is not set
+ CONFIG_DEBUG_KERNEL=y
++# CONFIG_DEBUG_SHIRQ is not set
+ CONFIG_LOG_BUF_SHIFT=14
+ CONFIG_DETECT_SOFTLOCKUP=y
+ # CONFIG_SCHEDSTATS is not set
++# CONFIG_TIMER_STATS is not set
+ # CONFIG_DEBUG_SLAB is not set
+ # CONFIG_DEBUG_RT_MUTEXES is not set
+ # CONFIG_RT_MUTEX_TESTER is not set
+ # CONFIG_DEBUG_SPINLOCK is not set
+ # CONFIG_DEBUG_MUTEXES is not set
+-# CONFIG_DEBUG_RWSEMS is not set
+ # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+ # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+ # CONFIG_DEBUG_KOBJECT is not set
+ CONFIG_DEBUG_BUGVERBOSE=y
+ # CONFIG_DEBUG_INFO is not set
+-# CONFIG_DEBUG_FS is not set
+ # CONFIG_DEBUG_VM is not set
+ # CONFIG_DEBUG_LIST is not set
+ CONFIG_FRAME_POINTER=y
+ CONFIG_FORCED_INLINING=y
+-# CONFIG_HEADERS_CHECK is not set
+ # CONFIG_RCU_TORTURE_TEST is not set
++# CONFIG_FAULT_INJECTION is not set
+ CONFIG_DEBUG_USER=y
+ # CONFIG_DEBUG_ERRORS is not set
+ CONFIG_DEBUG_LL=y
+@@ -1097,9 +1163,12 @@
+ #
+ # Library routines
+ #
++CONFIG_BITREVERSE=y
+ # CONFIG_CRC_CCITT is not set
+ # CONFIG_CRC16 is not set
+ CONFIG_CRC32=y
+ # CONFIG_LIBCRC32C is not set
+ CONFIG_ZLIB_INFLATE=y
+ CONFIG_PLIST=y
++CONFIG_HAS_IOMEM=y
++CONFIG_HAS_IOPORT=y
+diff -urN linux-2.6.22-rc5/arch/arm/configs/at91sam9263ek_defconfig linux-2.6.22-rc5.new/arch/arm/configs/at91sam9263ek_defconfig
+--- linux-2.6.22-rc5/arch/arm/configs/at91sam9263ek_defconfig	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/configs/at91sam9263ek_defconfig	2007-07-29 05:23:04.000000000 +0200
+@@ -1,11 +1,14 @@
+ #
+ # Automatically generated make config: don't edit
+-# Linux kernel version: 2.6.20-rc1
+-# Mon Jan  8 16:06:54 2007
++# Linux kernel version: 2.6.21
++# Mon May  7 11:42:49 2007
+ #
+ CONFIG_ARM=y
++CONFIG_SYS_SUPPORTS_APM_EMULATION=y
++CONFIG_GENERIC_GPIO=y
+ # CONFIG_GENERIC_TIME is not set
+ CONFIG_MMU=y
++# CONFIG_NO_IOPORT is not set
+ CONFIG_GENERIC_HARDIRQS=y
+ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+ CONFIG_HARDIRQS_SW_RESEND=y
+@@ -15,6 +18,7 @@
+ # CONFIG_ARCH_HAS_ILOG2_U64 is not set
+ CONFIG_GENERIC_HWEIGHT=y
+ CONFIG_GENERIC_CALIBRATE_DELAY=y
++CONFIG_ZONE_DMA=y
+ CONFIG_VECTORS_BASE=0xffff0000
+ CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+ 
+@@ -33,6 +37,7 @@
+ # CONFIG_SWAP is not set
+ CONFIG_SYSVIPC=y
+ # CONFIG_IPC_NS is not set
++CONFIG_SYSVIPC_SYSCTL=y
+ # CONFIG_POSIX_MQUEUE is not set
+ # CONFIG_BSD_PROCESS_ACCT is not set
+ # CONFIG_TASKSTATS is not set
+@@ -41,6 +46,7 @@
+ # CONFIG_IKCONFIG is not set
+ CONFIG_SYSFS_DEPRECATED=y
+ # CONFIG_RELAY is not set
++CONFIG_BLK_DEV_INITRD=y
+ CONFIG_INITRAMFS_SOURCE=""
+ CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+ CONFIG_SYSCTL=y
+@@ -120,6 +126,7 @@
+ # CONFIG_ARCH_IXP2000 is not set
+ # CONFIG_ARCH_IXP23XX is not set
+ # CONFIG_ARCH_L7200 is not set
++# CONFIG_ARCH_NS9XXX is not set
+ # CONFIG_ARCH_PNX4008 is not set
+ # CONFIG_ARCH_PXA is not set
+ # CONFIG_ARCH_RPC is not set
+@@ -152,6 +159,7 @@
+ # AT91 Feature Selections
+ #
+ # CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
++# CONFIG_ATMEL_TCLIB is not set
+ 
+ #
+ # Processor Type
+@@ -174,6 +182,7 @@
+ # CONFIG_CPU_DCACHE_DISABLE is not set
+ # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+ # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
++# CONFIG_OUTER_CACHE is not set
+ 
+ #
+ # Bus support
+@@ -201,6 +210,7 @@
+ # CONFIG_SPARSEMEM_STATIC is not set
+ CONFIG_SPLIT_PTLOCK_CPUS=4096
+ # CONFIG_RESOURCES_64BIT is not set
++CONFIG_ZONE_DMA_FLAG=1
+ # CONFIG_LEDS is not set
+ CONFIG_ALIGNMENT_TRAP=y
+ 
+@@ -211,6 +221,7 @@
+ CONFIG_ZBOOT_ROM_BSS=0x0
+ CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
+ # CONFIG_XIP_KERNEL is not set
++# CONFIG_KEXEC is not set
+ 
+ #
+ # Floating point emulation
+@@ -236,7 +247,6 @@
+ # Power management options
+ #
+ # CONFIG_PM is not set
+-# CONFIG_APM is not set
+ 
+ #
+ # Networking
+@@ -333,6 +343,7 @@
+ CONFIG_PREVENT_FIRMWARE_BUILD=y
+ # CONFIG_FW_LOADER is not set
+ # CONFIG_DEBUG_DRIVER is not set
++# CONFIG_DEBUG_DEVRES is not set
+ # CONFIG_SYS_HYPERVISOR is not set
+ 
+ #
+@@ -430,6 +441,7 @@
+ #
+ # Plug and Play support
+ #
++# CONFIG_PNPACPI is not set
+ 
+ #
+ # Block devices
+@@ -443,7 +455,6 @@
+ CONFIG_BLK_DEV_RAM_COUNT=16
+ CONFIG_BLK_DEV_RAM_SIZE=8192
+ CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+-CONFIG_BLK_DEV_INITRD=y
+ # CONFIG_CDROM_PKTCDVD is not set
+ # CONFIG_ATA_OVER_ETH is not set
+ 
+@@ -531,6 +542,7 @@
+ #
+ CONFIG_NET_ETHERNET=y
+ CONFIG_MII=y
++CONFIG_MACB=y
+ # CONFIG_SMC91X is not set
+ # CONFIG_DM9000 is not set
+ 
+@@ -685,6 +697,7 @@
+ # I2C Hardware Bus support
+ #
+ CONFIG_I2C_AT91=y
++CONFIG_I2C_AT91_CLOCKRATE=100000
+ # CONFIG_I2C_OCORES is not set
+ # CONFIG_I2C_PARPORT_LIGHT is not set
+ # CONFIG_I2C_STUB is not set
+@@ -722,6 +735,7 @@
+ #
+ # SPI Protocol Masters
+ #
++# CONFIG_SPI_AT25 is not set
+ 
+ #
+ # Dallas's 1-wire bus
+@@ -737,7 +751,11 @@
+ #
+ # Misc devices
+ #
+-# CONFIG_TIFM_CORE is not set
++
++#
++# Multifunction device drivers
++#
++# CONFIG_MFD_SM501 is not set
+ 
+ #
+ # LED devices
+@@ -766,15 +784,23 @@
+ #
+ # Graphics support
+ #
+-# CONFIG_FIRMWARE_EDID is not set
++# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+ CONFIG_FB=y
++# CONFIG_FIRMWARE_EDID is not set
++# CONFIG_FB_DDC is not set
+ # CONFIG_FB_CFB_FILLRECT is not set
+ # CONFIG_FB_CFB_COPYAREA is not set
+ # CONFIG_FB_CFB_IMAGEBLIT is not set
++# CONFIG_FB_SVGALIB is not set
+ # CONFIG_FB_MACMODES is not set
+ # CONFIG_FB_BACKLIGHT is not set
+ # CONFIG_FB_MODE_HELPERS is not set
+ # CONFIG_FB_TILEBLITTING is not set
++
++#
++# Frame buffer hardware drivers
++#
++# CONFIG_FB_S1D15605 is not set
+ # CONFIG_FB_S1D13XXX is not set
+ # CONFIG_FB_VIRTUAL is not set
+ 
+@@ -789,7 +815,6 @@
+ # Logo configuration
+ #
+ # CONFIG_LOGO is not set
+-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+ 
+ #
+ # Sound
+@@ -800,6 +825,7 @@
+ # HID Devices
+ #
+ CONFIG_HID=y
++# CONFIG_HID_DEBUG is not set
+ 
+ #
+ # USB support
+@@ -814,9 +840,7 @@
+ # Miscellaneous USB options
+ #
+ CONFIG_USB_DEVICEFS=y
+-# CONFIG_USB_BANDWIDTH is not set
+ # CONFIG_USB_DYNAMIC_MINORS is not set
+-# CONFIG_USB_MULTITHREAD_PROBE is not set
+ # CONFIG_USB_OTG is not set
+ 
+ #
+@@ -824,7 +848,8 @@
+ #
+ # CONFIG_USB_ISP116X_HCD is not set
+ CONFIG_USB_OHCI_HCD=y
+-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
++# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
++# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+ CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+ # CONFIG_USB_SL811_HCD is not set
+ 
+@@ -877,6 +902,7 @@
+ # CONFIG_USB_ATI_REMOTE2 is not set
+ # CONFIG_USB_KEYSPAN_REMOTE is not set
+ # CONFIG_USB_APPLETOUCH is not set
++# CONFIG_USB_GTCO is not set
+ 
+ #
+ # USB Imaging devices
+@@ -914,6 +940,7 @@
+ # CONFIG_USB_RIO500 is not set
+ # CONFIG_USB_LEGOTOWER is not set
+ # CONFIG_USB_LCD is not set
++# CONFIG_USB_BERRY_CHARGE is not set
+ # CONFIG_USB_LED is not set
+ # CONFIG_USB_CYPRESS_CY7C63 is not set
+ # CONFIG_USB_CYTHERM is not set
+@@ -923,6 +950,7 @@
+ # CONFIG_USB_APPLEDISPLAY is not set
+ # CONFIG_USB_LD is not set
+ # CONFIG_USB_TRANCEVIBRATOR is not set
++# CONFIG_USB_IOWARRIOR is not set
+ # CONFIG_USB_TEST is not set
+ 
+ #
+@@ -959,7 +987,6 @@
+ # CONFIG_MMC_DEBUG is not set
+ CONFIG_MMC_BLOCK=y
+ CONFIG_MMC_AT91=m
+-# CONFIG_MMC_TIFM_SD is not set
+ 
+ #
+ # Real Time Clock
+@@ -1136,15 +1163,16 @@
+ # CONFIG_DEBUG_FS is not set
+ # CONFIG_HEADERS_CHECK is not set
+ CONFIG_DEBUG_KERNEL=y
++# CONFIG_DEBUG_SHIRQ is not set
+ CONFIG_LOG_BUF_SHIFT=14
+ CONFIG_DETECT_SOFTLOCKUP=y
+ # CONFIG_SCHEDSTATS is not set
++# CONFIG_TIMER_STATS is not set
+ # CONFIG_DEBUG_SLAB is not set
+ # CONFIG_DEBUG_RT_MUTEXES is not set
+ # CONFIG_RT_MUTEX_TESTER is not set
+ # CONFIG_DEBUG_SPINLOCK is not set
+ # CONFIG_DEBUG_MUTEXES is not set
+-# CONFIG_DEBUG_RWSEMS is not set
+ # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+ # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+ # CONFIG_DEBUG_KOBJECT is not set
+@@ -1155,6 +1183,7 @@
+ CONFIG_FRAME_POINTER=y
+ CONFIG_FORCED_INLINING=y
+ # CONFIG_RCU_TORTURE_TEST is not set
++# CONFIG_FAULT_INJECTION is not set
+ CONFIG_DEBUG_USER=y
+ # CONFIG_DEBUG_ERRORS is not set
+ CONFIG_DEBUG_LL=y
+@@ -1180,5 +1209,7 @@
+ CONFIG_CRC32=y
+ # CONFIG_LIBCRC32C is not set
+ CONFIG_ZLIB_INFLATE=y
++CONFIG_ZLIB_DEFLATE=y
+ CONFIG_PLIST=y
+-CONFIG_IOMAP_COPY=y
++CONFIG_HAS_IOMEM=y
++CONFIG_HAS_IOPORT=y
+diff -urN linux-2.6.22-rc5/arch/arm/configs/cam60_defconfig linux-2.6.22-rc5.new/arch/arm/configs/cam60_defconfig
+--- linux-2.6.22-rc5/arch/arm/configs/cam60_defconfig	1970-01-01 01:00:00.000000000 +0100
++++ linux-2.6.22-rc5.new/arch/arm/configs/cam60_defconfig	2007-07-29 05:23:04.000000000 +0200
+@@ -0,0 +1,954 @@
++#
++# Automatically generated make config: don't edit
++# Linux kernel version: 2.6.20
++# Tue May  1 21:06:33 2007
++#
++CONFIG_ARM=y
++# CONFIG_GENERIC_TIME is not set
++CONFIG_MMU=y
++CONFIG_GENERIC_HARDIRQS=y
++CONFIG_TRACE_IRQFLAGS_SUPPORT=y
++CONFIG_HARDIRQS_SW_RESEND=y
++CONFIG_GENERIC_IRQ_PROBE=y
++CONFIG_RWSEM_GENERIC_SPINLOCK=y
++# CONFIG_ARCH_HAS_ILOG2_U32 is not set
++# CONFIG_ARCH_HAS_ILOG2_U64 is not set
++CONFIG_GENERIC_HWEIGHT=y
++CONFIG_GENERIC_CALIBRATE_DELAY=y
++CONFIG_VECTORS_BASE=0xffff0000
++CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
++
++#
++# Code maturity level options
++#
++CONFIG_EXPERIMENTAL=y
++CONFIG_BROKEN_ON_SMP=y
++CONFIG_INIT_ENV_ARG_LIMIT=32
++
++#
++# General setup
++#
++CONFIG_LOCALVERSION=""
++# CONFIG_LOCALVERSION_AUTO is not set
++# CONFIG_SWAP is not set
++CONFIG_SYSVIPC=y
++# CONFIG_IPC_NS is not set
++# CONFIG_POSIX_MQUEUE is not set
++# CONFIG_BSD_PROCESS_ACCT is not set
++# CONFIG_TASKSTATS is not set
++# CONFIG_UTS_NS is not set
++# CONFIG_AUDIT is not set
++CONFIG_IKCONFIG=y
++CONFIG_IKCONFIG_PROC=y
++CONFIG_SYSFS_DEPRECATED=y
++# CONFIG_RELAY is not set
++CONFIG_INITRAMFS_SOURCE=""
++CONFIG_CC_OPTIMIZE_FOR_SIZE=y
++CONFIG_SYSCTL=y
++# CONFIG_EMBEDDED is not set
++CONFIG_UID16=y
++CONFIG_SYSCTL_SYSCALL=y
++CONFIG_KALLSYMS=y
++# CONFIG_KALLSYMS_ALL is not set
++# CONFIG_KALLSYMS_EXTRA_PASS is not set
++CONFIG_HOTPLUG=y
++CONFIG_PRINTK=y
++CONFIG_BUG=y
++CONFIG_ELF_CORE=y
++CONFIG_BASE_FULL=y
++CONFIG_FUTEX=y
++CONFIG_EPOLL=y
++CONFIG_SHMEM=y
++CONFIG_SLAB=y
++CONFIG_VM_EVENT_COUNTERS=y
++CONFIG_RT_MUTEXES=y
++# CONFIG_TINY_SHMEM is not set
++CONFIG_BASE_SMALL=0
++# CONFIG_SLOB is not set
++
++#
++# Loadable module support
++#
++CONFIG_MODULES=y
++CONFIG_MODULE_UNLOAD=y
++CONFIG_MODULE_FORCE_UNLOAD=y
++# CONFIG_MODVERSIONS is not set
++# CONFIG_MODULE_SRCVERSION_ALL is not set
++# CONFIG_KMOD is not set
++
++#
++# Block layer
++#
++CONFIG_BLOCK=y
++# CONFIG_LBD is not set
++# CONFIG_BLK_DEV_IO_TRACE is not set
++# CONFIG_LSF is not set
++
++#
++# IO Schedulers
++#
++CONFIG_IOSCHED_NOOP=y
++CONFIG_IOSCHED_AS=y
++# CONFIG_IOSCHED_DEADLINE is not set
++# CONFIG_IOSCHED_CFQ is not set
++CONFIG_DEFAULT_AS=y
++# CONFIG_DEFAULT_DEADLINE is not set
++# CONFIG_DEFAULT_CFQ is not set
++# CONFIG_DEFAULT_NOOP is not set
++CONFIG_DEFAULT_IOSCHED="anticipatory"
++
++#
++# System Type
++#
++# CONFIG_ARCH_AAEC2000 is not set
++# CONFIG_ARCH_INTEGRATOR is not set
++# CONFIG_ARCH_REALVIEW is not set
++# CONFIG_ARCH_VERSATILE is not set
++CONFIG_ARCH_AT91=y
++# CONFIG_ARCH_CLPS7500 is not set
++# CONFIG_ARCH_CLPS711X is not set
++# CONFIG_ARCH_CO285 is not set
++# CONFIG_ARCH_EBSA110 is not set
++# CONFIG_ARCH_EP93XX is not set
++# CONFIG_ARCH_FOOTBRIDGE is not set
++# CONFIG_ARCH_NETX is not set
++# CONFIG_ARCH_H720X is not set
++# CONFIG_ARCH_IMX is not set
++# CONFIG_ARCH_IOP32X is not set
++# CONFIG_ARCH_IOP33X is not set
++# CONFIG_ARCH_IOP13XX is not set
++# CONFIG_ARCH_IXP4XX is not set
++# CONFIG_ARCH_IXP2000 is not set
++# CONFIG_ARCH_IXP23XX is not set
++# CONFIG_ARCH_L7200 is not set
++# CONFIG_ARCH_PNX4008 is not set
++# CONFIG_ARCH_PXA is not set
++# CONFIG_ARCH_RPC is not set
++# CONFIG_ARCH_SA1100 is not set
++# CONFIG_ARCH_S3C2410 is not set
++# CONFIG_ARCH_SHARK is not set
++# CONFIG_ARCH_LH7A40X is not set
++# CONFIG_ARCH_OMAP is not set
++
++#
++# Atmel AT91 System-on-Chip
++#
++# CONFIG_ARCH_AT91RM9200 is not set
++CONFIG_ARCH_AT91SAM9260=y
++# CONFIG_ARCH_AT91SAM9261 is not set
++# CONFIG_ARCH_AT91SAM9263 is not set
++
++#
++# AT91SAM9260 Board Type
++#
++# CONFIG_MACH_AT91SAM9260EK is not set
++CONFIG_MACH_CAM60=y
++
++#
++# AT91 Board Options
++#
++
++#
++# AT91 Feature Selections
++#
++# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
++
++#
++# Processor Type
++#
++CONFIG_CPU_32=y
++CONFIG_CPU_ARM926T=y
++CONFIG_CPU_32v5=y
++CONFIG_CPU_ABRT_EV5TJ=y
++CONFIG_CPU_CACHE_VIVT=y
++CONFIG_CPU_COPY_V4WB=y
++CONFIG_CPU_TLB_V4WBI=y
++CONFIG_CPU_CP15=y
++CONFIG_CPU_CP15_MMU=y
++
++#
++# Processor Features
++#
++# CONFIG_ARM_THUMB is not set
++# CONFIG_CPU_ICACHE_DISABLE is not set
++# CONFIG_CPU_DCACHE_DISABLE is not set
++# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
++# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
++
++#
++# Bus support
++#
++
++#
++# PCCARD (PCMCIA/CardBus) support
++#
++# CONFIG_PCCARD is not set
++
++#
++# Kernel Features
++#
++# CONFIG_PREEMPT is not set
++# CONFIG_NO_IDLE_HZ is not set
++CONFIG_HZ=100
++# CONFIG_AEABI is not set
++# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
++CONFIG_SELECT_MEMORY_MODEL=y
++CONFIG_FLATMEM_MANUAL=y
++# CONFIG_DISCONTIGMEM_MANUAL is not set
++# CONFIG_SPARSEMEM_MANUAL is not set
++CONFIG_FLATMEM=y
++CONFIG_FLAT_NODE_MEM_MAP=y
++# CONFIG_SPARSEMEM_STATIC is not set
++CONFIG_SPLIT_PTLOCK_CPUS=4096
++# CONFIG_RESOURCES_64BIT is not set
++# CONFIG_LEDS is not set
++CONFIG_ALIGNMENT_TRAP=y
++
++#
++# Boot options
++#
++CONFIG_ZBOOT_ROM_TEXT=0x22000000
++CONFIG_ZBOOT_ROM_BSS=0x20004000
++# CONFIG_ZBOOT_ROM is not set
++CONFIG_CMDLINE="console=ttyS0,115200 noinitrd root=/dev/mtdblock3 rootfstype=jffs2 mem=64M"
++# CONFIG_XIP_KERNEL is not set
++
++#
++# Floating point emulation
++#
++
++#
++# At least one emulation must be selected
++#
++CONFIG_FPE_NWFPE=y
++# CONFIG_FPE_NWFPE_XP is not set
++# CONFIG_FPE_FASTFPE is not set
++# CONFIG_VFP is not set
++
++#
++# Userspace binary formats
++#
++CONFIG_BINFMT_ELF=y
++# CONFIG_BINFMT_AOUT is not set
++# CONFIG_BINFMT_MISC is not set
++# CONFIG_ARTHUR is not set
++
++#
++# Power management options
++#
++# CONFIG_PM is not set
++# CONFIG_APM is not set
++
++#
++# Networking
++#
++CONFIG_NET=y
++
++#
++# Networking options
++#
++# CONFIG_NETDEBUG is not set
++CONFIG_PACKET=y
++# CONFIG_PACKET_MMAP is not set
++CONFIG_UNIX=y
++CONFIG_XFRM=y
++# CONFIG_XFRM_USER is not set
++# CONFIG_XFRM_SUB_POLICY is not set
++# CONFIG_NET_KEY is not set
++CONFIG_INET=y
++# CONFIG_IP_MULTICAST is not set
++# CONFIG_IP_ADVANCED_ROUTER is not set
++CONFIG_IP_FIB_HASH=y
++CONFIG_IP_PNP=y
++# CONFIG_IP_PNP_DHCP is not set
++CONFIG_IP_PNP_BOOTP=y
++# CONFIG_IP_PNP_RARP is not set
++# CONFIG_NET_IPIP is not set
++# CONFIG_NET_IPGRE is not set
++# CONFIG_ARPD is not set
++# CONFIG_SYN_COOKIES is not set
++# CONFIG_INET_AH is not set
++# CONFIG_INET_ESP is not set
++# CONFIG_INET_IPCOMP is not set
++# CONFIG_INET_XFRM_TUNNEL is not set
++# CONFIG_INET_TUNNEL is not set
++CONFIG_INET_XFRM_MODE_TRANSPORT=y
++CONFIG_INET_XFRM_MODE_TUNNEL=y
++CONFIG_INET_XFRM_MODE_BEET=y
++CONFIG_INET_DIAG=y
++CONFIG_INET_TCP_DIAG=y
++# CONFIG_TCP_CONG_ADVANCED is not set
++CONFIG_TCP_CONG_CUBIC=y
++CONFIG_DEFAULT_TCP_CONG="cubic"
++# CONFIG_TCP_MD5SIG is not set
++# CONFIG_IPV6 is not set
++# CONFIG_INET6_XFRM_TUNNEL is not set
++# CONFIG_INET6_TUNNEL is not set
++# CONFIG_NETWORK_SECMARK is not set
++# CONFIG_NETFILTER is not set
++
++#
++# DCCP Configuration (EXPERIMENTAL)
++#
++# CONFIG_IP_DCCP is not set
++
++#
++# SCTP Configuration (EXPERIMENTAL)
++#
++# CONFIG_IP_SCTP is not set
++
++#
++# TIPC Configuration (EXPERIMENTAL)
++#
++# CONFIG_TIPC is not set
++# CONFIG_ATM is not set
++# CONFIG_BRIDGE is not set
++# CONFIG_VLAN_8021Q is not set
++# CONFIG_DECNET is not set
++# CONFIG_LLC2 is not set
++# CONFIG_IPX is not set
++# CONFIG_ATALK is not set
++# CONFIG_X25 is not set
++# CONFIG_LAPB is not set
++# CONFIG_ECONET is not set
++# CONFIG_WAN_ROUTER is not set
++
++#
++# QoS and/or fair queueing
++#
++# CONFIG_NET_SCHED is not set
++
++#
++# Network testing
++#
++# CONFIG_NET_PKTGEN is not set
++# CONFIG_HAMRADIO is not set
++# CONFIG_IRDA is not set
++# CONFIG_BT is not set
++# CONFIG_IEEE80211 is not set
++
++#
++# Device Drivers
++#
++
++#
++# Generic Driver Options
++#
++CONFIG_STANDALONE=y
++CONFIG_PREVENT_FIRMWARE_BUILD=y
++# CONFIG_FW_LOADER is not set
++# CONFIG_DEBUG_DRIVER is not set
++# CONFIG_SYS_HYPERVISOR is not set
++
++#
++# Connector - unified userspace <-> kernelspace linker
++#
++# CONFIG_CONNECTOR is not set
++
++#
++# Memory Technology Devices (MTD)
++#
++CONFIG_MTD=y
++# CONFIG_MTD_DEBUG is not set
++CONFIG_MTD_CONCAT=y
++CONFIG_MTD_PARTITIONS=y
++# CONFIG_MTD_REDBOOT_PARTS is not set
++CONFIG_MTD_CMDLINE_PARTS=y
++# CONFIG_MTD_AFS_PARTS is not set
++
++#
++# User Modules And Translation Layers
++#
++CONFIG_MTD_CHAR=y
++CONFIG_MTD_BLKDEVS=y
++CONFIG_MTD_BLOCK=y
++# CONFIG_FTL is not set
++# CONFIG_NFTL is not set
++# CONFIG_INFTL is not set
++# CONFIG_RFD_FTL is not set
++# CONFIG_SSFDC is not set
++
++#
++# RAM/ROM/Flash chip drivers
++#
++CONFIG_MTD_CFI=y
++# CONFIG_MTD_JEDECPROBE is not set
++CONFIG_MTD_GEN_PROBE=y
++# CONFIG_MTD_CFI_ADV_OPTIONS is not set
++CONFIG_MTD_MAP_BANK_WIDTH_1=y
++CONFIG_MTD_MAP_BANK_WIDTH_2=y
++CONFIG_MTD_MAP_BANK_WIDTH_4=y
++# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
++# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
++# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
++CONFIG_MTD_CFI_I1=y
++CONFIG_MTD_CFI_I2=y
++# CONFIG_MTD_CFI_I4 is not set
++# CONFIG_MTD_CFI_I8 is not set
++# CONFIG_MTD_CFI_INTELEXT is not set
++# CONFIG_MTD_CFI_AMDSTD is not set
++# CONFIG_MTD_CFI_STAA is not set
++# CONFIG_MTD_RAM is not set
++# CONFIG_MTD_ROM is not set
++# CONFIG_MTD_ABSENT is not set
++# CONFIG_MTD_OBSOLETE_CHIPS is not set
++
++#
++# Mapping drivers for chip access
++#
++CONFIG_MTD_COMPLEX_MAPPINGS=y
++# CONFIG_MTD_PHYSMAP is not set
++# CONFIG_MTD_ARM_INTEGRATOR is not set
++# CONFIG_MTD_PLATRAM is not set
++
++#
++# Self-contained MTD device drivers
++#
++CONFIG_MTD_DATAFLASH=y
++# CONFIG_MTD_M25P80 is not set
++# CONFIG_MTD_SLRAM is not set
++# CONFIG_MTD_PHRAM is not set
++# CONFIG_MTD_MTDRAM is not set
++# CONFIG_MTD_BLOCK2MTD is not set
++
++#
++# Disk-On-Chip Device Drivers
++#
++# CONFIG_MTD_DOC2000 is not set
++# CONFIG_MTD_DOC2001 is not set
++# CONFIG_MTD_DOC2001PLUS is not set
++
++#
++# NAND Flash Device Drivers
++#
++# CONFIG_MTD_NAND is not set
++
++#
++# OneNAND Flash Device Drivers
++#
++# CONFIG_MTD_ONENAND is not set
++
++#
++# Parallel port support
++#
++# CONFIG_PARPORT is not set
++
++#
++# Plug and Play support
++#
++
++#
++# Block devices
++#
++# CONFIG_BLK_DEV_COW_COMMON is not set
++# CONFIG_BLK_DEV_LOOP is not set
++# CONFIG_BLK_DEV_NBD is not set
++CONFIG_BLK_DEV_RAM=y
++CONFIG_BLK_DEV_RAM_COUNT=16
++CONFIG_BLK_DEV_RAM_SIZE=8192
++CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
++CONFIG_BLK_DEV_INITRD=y
++# CONFIG_CDROM_PKTCDVD is not set
++# CONFIG_ATA_OVER_ETH is not set
++
++#
++# SCSI device support
++#
++# CONFIG_RAID_ATTRS is not set
++# CONFIG_SCSI is not set
++# CONFIG_SCSI_NETLINK is not set
++
++#
++# Serial ATA (prod) and Parallel ATA (experimental) drivers
++#
++# CONFIG_ATA is not set
++
++#
++# Multi-device support (RAID and LVM)
++#
++# CONFIG_MD is not set
++
++#
++# Fusion MPT device support
++#
++# CONFIG_FUSION is not set
++
++#
++# IEEE 1394 (FireWire) support
++#
++
++#
++# I2O device support
++#
++
++#
++# Network device support
++#
++CONFIG_NETDEVICES=y
++# CONFIG_DUMMY is not set
++# CONFIG_BONDING is not set
++# CONFIG_EQUALIZER is not set
++# CONFIG_TUN is not set
++
++#
++# PHY device support
++#
++# CONFIG_PHYLIB is not set
++
++#
++# Ethernet (10 or 100Mbit)
++#
++CONFIG_NET_ETHERNET=y
++CONFIG_MII=y
++CONFIG_MACB=y
++# CONFIG_SMC91X is not set
++# CONFIG_DM9000 is not set
++
++#
++# Ethernet (1000 Mbit)
++#
++
++#
++# Ethernet (10000 Mbit)
++#
++
++#
++# Token Ring devices
++#
++
++#
++# Wireless LAN (non-hamradio)
++#
++# CONFIG_NET_RADIO is not set
++
++#
++# Wan interfaces
++#
++# CONFIG_WAN is not set
++# CONFIG_PPP is not set
++# CONFIG_SLIP is not set
++# CONFIG_SHAPER is not set
++# CONFIG_NETCONSOLE is not set
++# CONFIG_NETPOLL is not set
++# CONFIG_NET_POLL_CONTROLLER is not set
++
++#
++# ISDN subsystem
++#
++# CONFIG_ISDN is not set
++
++#
++# Input device support
++#
++CONFIG_INPUT=y
++# CONFIG_INPUT_FF_MEMLESS is not set
++
++#
++# Userland interfaces
++#
++CONFIG_INPUT_MOUSEDEV=y
++# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
++CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
++CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
++# CONFIG_INPUT_JOYDEV is not set
++# CONFIG_INPUT_TSDEV is not set
++# CONFIG_INPUT_EVDEV is not set
++# CONFIG_INPUT_EVBUG is not set
++
++#
++# Input Device Drivers
++#
++# CONFIG_INPUT_KEYBOARD is not set
++# CONFIG_INPUT_MOUSE is not set
++# CONFIG_INPUT_JOYSTICK is not set
++# CONFIG_INPUT_TOUCHSCREEN is not set
++# CONFIG_INPUT_MISC is not set
++
++#
++# Hardware I/O ports
++#
++# CONFIG_SERIO is not set
++# CONFIG_GAMEPORT is not set
++
++#
++# Character devices
++#
++CONFIG_VT=y
++CONFIG_VT_CONSOLE=y
++CONFIG_HW_CONSOLE=y
++# CONFIG_VT_HW_CONSOLE_BINDING is not set
++# CONFIG_SERIAL_NONSTANDARD is not set
++
++#
++# Serial drivers
++#
++# CONFIG_SERIAL_8250 is not set
++
++#
++# Non-8250 serial port support
++#
++CONFIG_SERIAL_ATMEL=y
++CONFIG_SERIAL_ATMEL_CONSOLE=y
++# CONFIG_SERIAL_ATMEL_TTYAT is not set
++CONFIG_SERIAL_CORE=y
++CONFIG_SERIAL_CORE_CONSOLE=y
++CONFIG_UNIX98_PTYS=y
++CONFIG_LEGACY_PTYS=y
++CONFIG_LEGACY_PTY_COUNT=256
++
++#
++# IPMI
++#
++# CONFIG_IPMI_HANDLER is not set
++
++#
++# Watchdog Cards
++#
++# CONFIG_WATCHDOG is not set
++# CONFIG_HW_RANDOM is not set
++# CONFIG_NVRAM is not set
++# CONFIG_DTLK is not set
++# CONFIG_R3964 is not set
++# CONFIG_RAW_DRIVER is not set
++
++#
++# TPM devices
++#
++# CONFIG_TCG_TPM is not set
++
++#
++# I2C support
++#
++# CONFIG_I2C is not set
++
++#
++# SPI support
++#
++CONFIG_SPI=y
++# CONFIG_SPI_DEBUG is not set
++CONFIG_SPI_MASTER=y
++
++#
++# SPI Master Controller Drivers
++#
++CONFIG_SPI_ATMEL=y
++# CONFIG_SPI_BITBANG is not set
++
++#
++# SPI Protocol Masters
++#
++
++#
++# Dallas's 1-wire bus
++#
++# CONFIG_W1 is not set
++
++#
++# Hardware Monitoring support
++#
++# CONFIG_HWMON is not set
++# CONFIG_HWMON_VID is not set
++
++#
++# Misc devices
++#
++# CONFIG_TIFM_CORE is not set
++
++#
++# LED devices
++#
++# CONFIG_NEW_LEDS is not set
++
++#
++# LED drivers
++#
++
++#
++# LED Triggers
++#
++
++#
++# Multimedia devices
++#
++# CONFIG_VIDEO_DEV is not set
++
++#
++# Digital Video Broadcasting Devices
++#
++# CONFIG_DVB is not set
++
++#
++# Graphics support
++#
++# CONFIG_FIRMWARE_EDID is not set
++# CONFIG_FB is not set
++
++#
++# Console display driver support
++#
++# CONFIG_VGA_CONSOLE is not set
++CONFIG_DUMMY_CONSOLE=y
++# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
++
++#
++# Sound
++#
++# CONFIG_SOUND is not set
++
++#
++# HID Devices
++#
++# CONFIG_HID is not set
++
++#
++# USB support
++#
++CONFIG_USB_ARCH_HAS_HCD=y
++CONFIG_USB_ARCH_HAS_OHCI=y
++# CONFIG_USB_ARCH_HAS_EHCI is not set
++# CONFIG_USB is not set
++
++#
++# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
++#
++
++#
++# USB Gadget Support
++#
++# CONFIG_USB_GADGET is not set
++
++#
++# MMC/SD Card support
++#
++# CONFIG_MMC is not set
++
++#
++# Real Time Clock
++#
++CONFIG_RTC_LIB=y
++# CONFIG_RTC_CLASS is not set
++
++#
++# File systems
++#
++CONFIG_EXT2_FS=y
++# CONFIG_EXT2_FS_XATTR is not set
++# CONFIG_EXT2_FS_XIP is not set
++CONFIG_EXT3_FS=y
++CONFIG_EXT3_FS_XATTR=y
++# CONFIG_EXT3_FS_POSIX_ACL is not set
++# CONFIG_EXT3_FS_SECURITY is not set
++# CONFIG_EXT4DEV_FS is not set
++CONFIG_JBD=y
++# CONFIG_JBD_DEBUG is not set
++CONFIG_FS_MBCACHE=y
++# CONFIG_REISERFS_FS is not set
++# CONFIG_JFS_FS is not set
++# CONFIG_FS_POSIX_ACL is not set
++# CONFIG_XFS_FS is not set
++# CONFIG_GFS2_FS is not set
++# CONFIG_OCFS2_FS is not set
++# CONFIG_MINIX_FS is not set
++# CONFIG_ROMFS_FS is not set
++CONFIG_INOTIFY=y
++CONFIG_INOTIFY_USER=y
++# CONFIG_QUOTA is not set
++CONFIG_DNOTIFY=y
++# CONFIG_AUTOFS_FS is not set
++CONFIG_AUTOFS4_FS=y
++# CONFIG_FUSE_FS is not set
++
++#
++# CD-ROM/DVD Filesystems
++#
++# CONFIG_ISO9660_FS is not set
++# CONFIG_UDF_FS is not set
++
++#
++# DOS/FAT/NT Filesystems
++#
++CONFIG_FAT_FS=y
++# CONFIG_MSDOS_FS is not set
++CONFIG_VFAT_FS=y
++CONFIG_FAT_DEFAULT_CODEPAGE=437
++CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
++# CONFIG_NTFS_FS is not set
++
++#
++# Pseudo filesystems
++#
++CONFIG_PROC_FS=y
++CONFIG_PROC_SYSCTL=y
++CONFIG_SYSFS=y
++CONFIG_TMPFS=y
++# CONFIG_TMPFS_POSIX_ACL is not set
++# CONFIG_HUGETLB_PAGE is not set
++CONFIG_RAMFS=y
++# CONFIG_CONFIGFS_FS is not set
++
++#
++# Miscellaneous filesystems
++#
++# CONFIG_ADFS_FS is not set
++# CONFIG_AFFS_FS is not set
++# CONFIG_HFS_FS is not set
++# CONFIG_HFSPLUS_FS is not set
++# CONFIG_BEFS_FS is not set
++# CONFIG_BFS_FS is not set
++# CONFIG_EFS_FS is not set
++CONFIG_JFFS2_FS=y
++CONFIG_JFFS2_FS_DEBUG=0
++CONFIG_JFFS2_FS_WRITEBUFFER=y
++# CONFIG_JFFS2_SUMMARY is not set
++# CONFIG_JFFS2_FS_XATTR is not set
++# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
++CONFIG_JFFS2_ZLIB=y
++CONFIG_JFFS2_RTIME=y
++# CONFIG_JFFS2_RUBIN is not set
++CONFIG_CRAMFS=y
++# CONFIG_VXFS_FS is not set
++# CONFIG_HPFS_FS is not set
++# CONFIG_QNX4FS_FS is not set
++# CONFIG_SYSV_FS is not set
++# CONFIG_UFS_FS is not set
++
++#
++# Network File Systems
++#
++CONFIG_NFS_FS=y
++CONFIG_NFS_V3=y
++# CONFIG_NFS_V3_ACL is not set
++# CONFIG_NFS_V4 is not set
++# CONFIG_NFS_DIRECTIO is not set
++# CONFIG_NFSD is not set
++CONFIG_ROOT_NFS=y
++CONFIG_LOCKD=y
++CONFIG_LOCKD_V4=y
++CONFIG_NFS_COMMON=y
++CONFIG_SUNRPC=y
++# CONFIG_RPCSEC_GSS_KRB5 is not set
++# CONFIG_RPCSEC_GSS_SPKM3 is not set
++# CONFIG_SMB_FS is not set
++# CONFIG_CIFS is not set
++# CONFIG_NCP_FS is not set
++# CONFIG_CODA_FS is not set
++# CONFIG_AFS_FS is not set
++# CONFIG_9P_FS is not set
++
++#
++# Partition Types
++#
++# CONFIG_PARTITION_ADVANCED is not set
++CONFIG_MSDOS_PARTITION=y
++
++#
++# Native Language Support
++#
++CONFIG_NLS=y
++CONFIG_NLS_DEFAULT="iso8859-1"
++CONFIG_NLS_CODEPAGE_437=y
++# CONFIG_NLS_CODEPAGE_737 is not set
++# CONFIG_NLS_CODEPAGE_775 is not set
++CONFIG_NLS_CODEPAGE_850=y
++# CONFIG_NLS_CODEPAGE_852 is not set
++# CONFIG_NLS_CODEPAGE_855 is not set
++# CONFIG_NLS_CODEPAGE_857 is not set
++# CONFIG_NLS_CODEPAGE_860 is not set
++# CONFIG_NLS_CODEPAGE_861 is not set
++# CONFIG_NLS_CODEPAGE_862 is not set
++# CONFIG_NLS_CODEPAGE_863 is not set
++# CONFIG_NLS_CODEPAGE_864 is not set
++# CONFIG_NLS_CODEPAGE_865 is not set
++# CONFIG_NLS_CODEPAGE_866 is not set
++# CONFIG_NLS_CODEPAGE_869 is not set
++# CONFIG_NLS_CODEPAGE_936 is not set
++# CONFIG_NLS_CODEPAGE_950 is not set
++# CONFIG_NLS_CODEPAGE_932 is not set
++# CONFIG_NLS_CODEPAGE_949 is not set
++# CONFIG_NLS_CODEPAGE_874 is not set
++# CONFIG_NLS_ISO8859_8 is not set
++# CONFIG_NLS_CODEPAGE_1250 is not set
++# CONFIG_NLS_CODEPAGE_1251 is not set
++# CONFIG_NLS_ASCII is not set
++CONFIG_NLS_ISO8859_1=y
++# CONFIG_NLS_ISO8859_2 is not set
++# CONFIG_NLS_ISO8859_3 is not set
++# CONFIG_NLS_ISO8859_4 is not set
++# CONFIG_NLS_ISO8859_5 is not set
++# CONFIG_NLS_ISO8859_6 is not set
++# CONFIG_NLS_ISO8859_7 is not set
++# CONFIG_NLS_ISO8859_9 is not set
++# CONFIG_NLS_ISO8859_13 is not set
++# CONFIG_NLS_ISO8859_14 is not set
++# CONFIG_NLS_ISO8859_15 is not set
++# CONFIG_NLS_KOI8_R is not set
++# CONFIG_NLS_KOI8_U is not set
++# CONFIG_NLS_UTF8 is not set
++
++#
++# Distributed Lock Manager
++#
++# CONFIG_DLM is not set
++
++#
++# Profiling support
++#
++# CONFIG_PROFILING is not set
++
++#
++# Kernel hacking
++#
++# CONFIG_PRINTK_TIME is not set
++CONFIG_ENABLE_MUST_CHECK=y
++# CONFIG_MAGIC_SYSRQ is not set
++# CONFIG_UNUSED_SYMBOLS is not set
++# CONFIG_DEBUG_FS is not set
++# CONFIG_HEADERS_CHECK is not set
++CONFIG_DEBUG_KERNEL=y
++CONFIG_LOG_BUF_SHIFT=14
++CONFIG_DETECT_SOFTLOCKUP=y
++# CONFIG_SCHEDSTATS is not set
++# CONFIG_DEBUG_SLAB is not set
++# CONFIG_DEBUG_RT_MUTEXES is not set
++# CONFIG_RT_MUTEX_TESTER is not set
++# CONFIG_DEBUG_SPINLOCK is not set
++# CONFIG_DEBUG_MUTEXES is not set
++# CONFIG_DEBUG_RWSEMS is not set
++# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
++# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
++# CONFIG_DEBUG_KOBJECT is not set
++CONFIG_DEBUG_BUGVERBOSE=y
++# CONFIG_DEBUG_INFO is not set
++# CONFIG_DEBUG_VM is not set
++# CONFIG_DEBUG_LIST is not set
++CONFIG_FRAME_POINTER=y
++CONFIG_FORCED_INLINING=y
++# CONFIG_RCU_TORTURE_TEST is not set
++CONFIG_DEBUG_USER=y
++# CONFIG_DEBUG_ERRORS is not set
++CONFIG_DEBUG_LL=y
++# CONFIG_DEBUG_ICEDCC is not set
++
++#
++# Security options
++#
++# CONFIG_KEYS is not set
++# CONFIG_SECURITY is not set
++
++#
++# Cryptographic options
++#
++# CONFIG_CRYPTO is not set
++
++#
++# Library routines
++#
++CONFIG_BITREVERSE=y
++# CONFIG_CRC_CCITT is not set
++# CONFIG_CRC16 is not set
++CONFIG_CRC32=y
++# CONFIG_LIBCRC32C is not set
++CONFIG_ZLIB_INFLATE=y
++CONFIG_ZLIB_DEFLATE=y
++CONFIG_PLIST=y
++CONFIG_IOMAP_COPY=y
+diff -urN linux-2.6.22-rc5/arch/arm/configs/kb9202_defconfig linux-2.6.22-rc5.new/arch/arm/configs/kb9202_defconfig
+--- linux-2.6.22-rc5/arch/arm/configs/kb9202_defconfig	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/configs/kb9202_defconfig	2007-07-29 05:23:04.000000000 +0200
+@@ -1,19 +1,31 @@
+ #
+ # Automatically generated make config: don't edit
+-# Linux kernel version: 2.6.13-rc2
+-# Sun Aug 14 19:26:59 2005
++# Linux kernel version: 2.6.21
++# Mon May  7 11:43:14 2007
+ #
+ CONFIG_ARM=y
++CONFIG_SYS_SUPPORTS_APM_EMULATION=y
++CONFIG_GENERIC_GPIO=y
++# CONFIG_GENERIC_TIME is not set
+ CONFIG_MMU=y
+-CONFIG_UID16=y
++# CONFIG_NO_IOPORT is not set
++CONFIG_GENERIC_HARDIRQS=y
++CONFIG_TRACE_IRQFLAGS_SUPPORT=y
++CONFIG_HARDIRQS_SW_RESEND=y
++CONFIG_GENERIC_IRQ_PROBE=y
+ CONFIG_RWSEM_GENERIC_SPINLOCK=y
++# CONFIG_ARCH_HAS_ILOG2_U32 is not set
++# CONFIG_ARCH_HAS_ILOG2_U64 is not set
++CONFIG_GENERIC_HWEIGHT=y
+ CONFIG_GENERIC_CALIBRATE_DELAY=y
++CONFIG_ZONE_DMA=y
++CONFIG_VECTORS_BASE=0xffff0000
++CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+ 
+ #
+ # Code maturity level options
+ #
+-# CONFIG_EXPERIMENTAL is not set
+-CONFIG_CLEAN_COMPILE=y
++CONFIG_EXPERIMENTAL=y
+ CONFIG_BROKEN_ON_SMP=y
+ CONFIG_INIT_ENV_ARG_LIMIT=32
+ 
+@@ -21,54 +33,103 @@
+ # General setup
+ #
+ CONFIG_LOCALVERSION=""
+-# CONFIG_SWAP is not set
+-# CONFIG_SYSVIPC is not set
+-# CONFIG_BSD_PROCESS_ACCT is not set
++CONFIG_LOCALVERSION_AUTO=y
++CONFIG_SWAP=y
++CONFIG_SYSVIPC=y
++# CONFIG_IPC_NS is not set
++CONFIG_SYSVIPC_SYSCTL=y
++CONFIG_POSIX_MQUEUE=y
++CONFIG_BSD_PROCESS_ACCT=y
++# CONFIG_BSD_PROCESS_ACCT_V3 is not set
++# CONFIG_TASKSTATS is not set
++# CONFIG_UTS_NS is not set
++CONFIG_AUDIT=y
++CONFIG_IKCONFIG=y
++CONFIG_IKCONFIG_PROC=y
++CONFIG_SYSFS_DEPRECATED=y
++# CONFIG_RELAY is not set
++CONFIG_BLK_DEV_INITRD=y
++CONFIG_INITRAMFS_SOURCE=""
++# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+ CONFIG_SYSCTL=y
+-# CONFIG_AUDIT is not set
+-CONFIG_HOTPLUG=y
+-# CONFIG_KOBJECT_UEVENT is not set
+-# CONFIG_IKCONFIG is not set
+ # CONFIG_EMBEDDED is not set
++CONFIG_UID16=y
++CONFIG_SYSCTL_SYSCALL=y
+ CONFIG_KALLSYMS=y
+ # CONFIG_KALLSYMS_ALL is not set
+-# CONFIG_KALLSYMS_EXTRA_PASS is not set
++CONFIG_KALLSYMS_EXTRA_PASS=y
++CONFIG_HOTPLUG=y
+ CONFIG_PRINTK=y
+ CONFIG_BUG=y
++CONFIG_ELF_CORE=y
+ CONFIG_BASE_FULL=y
+ CONFIG_FUTEX=y
+ CONFIG_EPOLL=y
+-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+ CONFIG_SHMEM=y
+-CONFIG_CC_ALIGN_FUNCTIONS=0
+-CONFIG_CC_ALIGN_LABELS=0
+-CONFIG_CC_ALIGN_LOOPS=0
+-CONFIG_CC_ALIGN_JUMPS=0
++CONFIG_SLAB=y
++CONFIG_VM_EVENT_COUNTERS=y
++CONFIG_RT_MUTEXES=y
+ # CONFIG_TINY_SHMEM is not set
+ CONFIG_BASE_SMALL=0
++# CONFIG_SLOB is not set
+ 
+ #
+ # Loadable module support
+ #
+ CONFIG_MODULES=y
+ CONFIG_MODULE_UNLOAD=y
+-CONFIG_OBSOLETE_MODPARM=y
+-# CONFIG_MODULE_SRCVERSION_ALL is not set
++# CONFIG_MODULE_FORCE_UNLOAD is not set
++CONFIG_MODVERSIONS=y
++CONFIG_MODULE_SRCVERSION_ALL=y
+ CONFIG_KMOD=y
+ 
+ #
++# Block layer
++#
++CONFIG_BLOCK=y
++CONFIG_LBD=y
++# CONFIG_BLK_DEV_IO_TRACE is not set
++# CONFIG_LSF is not set
++
++#
++# IO Schedulers
++#
++CONFIG_IOSCHED_NOOP=y
++CONFIG_IOSCHED_AS=y
++CONFIG_IOSCHED_DEADLINE=y
++CONFIG_IOSCHED_CFQ=y
++# CONFIG_DEFAULT_AS is not set
++# CONFIG_DEFAULT_DEADLINE is not set
++CONFIG_DEFAULT_CFQ=y
++# CONFIG_DEFAULT_NOOP is not set
++CONFIG_DEFAULT_IOSCHED="cfq"
++
++#
+ # System Type
+ #
++# CONFIG_ARCH_AAEC2000 is not set
++# CONFIG_ARCH_INTEGRATOR is not set
++# CONFIG_ARCH_REALVIEW is not set
++# CONFIG_ARCH_VERSATILE is not set
++CONFIG_ARCH_AT91=y
+ # CONFIG_ARCH_CLPS7500 is not set
+ # CONFIG_ARCH_CLPS711X is not set
+ # CONFIG_ARCH_CO285 is not set
+ # CONFIG_ARCH_EBSA110 is not set
++# CONFIG_ARCH_EP93XX is not set
+ # CONFIG_ARCH_FOOTBRIDGE is not set
+-# CONFIG_ARCH_INTEGRATOR is not set
+-# CONFIG_ARCH_IOP3XX is not set
++# CONFIG_ARCH_NETX is not set
++# CONFIG_ARCH_H720X is not set
++# CONFIG_ARCH_IMX is not set
++# CONFIG_ARCH_IOP32X is not set
++# CONFIG_ARCH_IOP33X is not set
++# CONFIG_ARCH_IOP13XX is not set
+ # CONFIG_ARCH_IXP4XX is not set
+ # CONFIG_ARCH_IXP2000 is not set
++# CONFIG_ARCH_IXP23XX is not set
+ # CONFIG_ARCH_L7200 is not set
++# CONFIG_ARCH_NS9XXX is not set
++# CONFIG_ARCH_PNX4008 is not set
+ # CONFIG_ARCH_PXA is not set
+ # CONFIG_ARCH_RPC is not set
+ # CONFIG_ARCH_SA1100 is not set
+@@ -76,34 +137,52 @@
+ # CONFIG_ARCH_SHARK is not set
+ # CONFIG_ARCH_LH7A40X is not set
+ # CONFIG_ARCH_OMAP is not set
+-# CONFIG_ARCH_VERSATILE is not set
+-# CONFIG_ARCH_IMX is not set
+-# CONFIG_ARCH_H720X is not set
+-# CONFIG_ARCH_AAEC2000 is not set
+-CONFIG_ARCH_AT91=y
++
++#
++# Atmel AT91 System-on-Chip
++#
+ CONFIG_ARCH_AT91RM9200=y
++# CONFIG_ARCH_AT91SAM9260 is not set
++# CONFIG_ARCH_AT91SAM9261 is not set
++# CONFIG_ARCH_AT91SAM9263 is not set
+ 
+ #
+-# AT91RM9200 Implementations
++# AT91RM9200 Board Type
+ #
++# CONFIG_MACH_ONEARM is not set
+ # CONFIG_ARCH_AT91RM9200DK is not set
+ # CONFIG_MACH_AT91RM9200EK is not set
+ # CONFIG_MACH_CSB337 is not set
+ # CONFIG_MACH_CSB637 is not set
+ # CONFIG_MACH_CARMEVA is not set
++# CONFIG_MACH_ATEB9200 is not set
+ CONFIG_MACH_KB9200=y
++# CONFIG_MACH_KAFA is not set
++# CONFIG_MACH_CHUB is not set
++
++#
++# AT91 Board Options
++#
++
++#
++# AT91 Feature Selections
++#
++# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
++# CONFIG_ATMEL_TCLIB is not set
+ 
+ #
+ # Processor Type
+ #
+ CONFIG_CPU_32=y
+ CONFIG_CPU_ARM920T=y
+-CONFIG_CPU_32v4=y
++CONFIG_CPU_32v4T=y
+ CONFIG_CPU_ABRT_EV4T=y
+ CONFIG_CPU_CACHE_V4WT=y
+ CONFIG_CPU_CACHE_VIVT=y
+ CONFIG_CPU_COPY_V4WB=y
+ CONFIG_CPU_TLB_V4WBI=y
++CONFIG_CPU_CP15=y
++CONFIG_CPU_CP15_MMU=y
+ 
+ #
+ # Processor Features
+@@ -112,24 +191,44 @@
+ # CONFIG_CPU_ICACHE_DISABLE is not set
+ # CONFIG_CPU_DCACHE_DISABLE is not set
+ # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
++# CONFIG_OUTER_CACHE is not set
+ 
+ #
+ # Bus support
+ #
+-CONFIG_ISA_DMA_API=y
+ 
+ #
+ # PCCARD (PCMCIA/CardBus) support
+ #
+-# CONFIG_PCCARD is not set
++CONFIG_PCCARD=m
++# CONFIG_PCMCIA_DEBUG is not set
++CONFIG_PCMCIA=m
++CONFIG_PCMCIA_LOAD_CIS=y
++CONFIG_PCMCIA_IOCTL=y
++
++#
++# PC-card bridges
++#
++# CONFIG_AT91_CF is not set
+ 
+ #
+ # Kernel Features
+ #
++# CONFIG_PREEMPT is not set
+ # CONFIG_NO_IDLE_HZ is not set
++CONFIG_HZ=100
++# CONFIG_AEABI is not set
+ # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
++CONFIG_SELECT_MEMORY_MODEL=y
++CONFIG_FLATMEM_MANUAL=y
++# CONFIG_DISCONTIGMEM_MANUAL is not set
++# CONFIG_SPARSEMEM_MANUAL is not set
+ CONFIG_FLATMEM=y
+ CONFIG_FLAT_NODE_MEM_MAP=y
++# CONFIG_SPARSEMEM_STATIC is not set
++CONFIG_SPLIT_PTLOCK_CPUS=4096
++# CONFIG_RESOURCES_64BIT is not set
++CONFIG_ZONE_DMA_FLAG=1
+ # CONFIG_LEDS is not set
+ CONFIG_ALIGNMENT_TRAP=y
+ 
+@@ -138,8 +237,10 @@
+ #
+ CONFIG_ZBOOT_ROM_TEXT=0x10000000
+ CONFIG_ZBOOT_ROM_BSS=0x20040000
+-CONFIG_ZBOOT_ROM=y
+-CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/ram rw initrd=0x20210000,654933"
++# CONFIG_ZBOOT_ROM is not set
++CONFIG_CMDLINE="noinitrd root=/dev/mtdblock0 rootfstype=jffs2 mem=64M"
++# CONFIG_XIP_KERNEL is not set
++# CONFIG_KEXEC is not set
+ 
+ #
+ # Floating point emulation
+@@ -150,6 +251,7 @@
+ #
+ CONFIG_FPE_NWFPE=y
+ # CONFIG_FPE_NWFPE_XP is not set
++# CONFIG_FPE_FASTFPE is not set
+ 
+ #
+ # Userspace binary formats
+@@ -165,6 +267,96 @@
+ # CONFIG_PM is not set
+ 
+ #
++# Networking
++#
++CONFIG_NET=y
++
++#
++# Networking options
++#
++# CONFIG_NETDEBUG is not set
++CONFIG_PACKET=y
++# CONFIG_PACKET_MMAP is not set
++CONFIG_UNIX=y
++# CONFIG_NET_KEY is not set
++CONFIG_INET=y
++CONFIG_IP_MULTICAST=y
++# CONFIG_IP_ADVANCED_ROUTER is not set
++CONFIG_IP_FIB_HASH=y
++CONFIG_IP_PNP=y
++# CONFIG_IP_PNP_DHCP is not set
++# CONFIG_IP_PNP_BOOTP is not set
++# CONFIG_IP_PNP_RARP is not set
++# CONFIG_NET_IPIP is not set
++# CONFIG_NET_IPGRE is not set
++# CONFIG_IP_MROUTE is not set
++# CONFIG_ARPD is not set
++# CONFIG_SYN_COOKIES is not set
++# CONFIG_INET_AH is not set
++# CONFIG_INET_ESP is not set
++# CONFIG_INET_IPCOMP is not set
++# CONFIG_INET_XFRM_TUNNEL is not set
++# CONFIG_INET_TUNNEL is not set
++# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
++# CONFIG_INET_XFRM_MODE_TUNNEL is not set
++# CONFIG_INET_XFRM_MODE_BEET is not set
++# CONFIG_INET_DIAG is not set
++# CONFIG_TCP_CONG_ADVANCED is not set
++CONFIG_TCP_CONG_CUBIC=y
++CONFIG_DEFAULT_TCP_CONG="cubic"
++# CONFIG_TCP_MD5SIG is not set
++# CONFIG_IPV6 is not set
++# CONFIG_INET6_XFRM_TUNNEL is not set
++# CONFIG_INET6_TUNNEL is not set
++# CONFIG_NETWORK_SECMARK is not set
++# CONFIG_NETFILTER is not set
++
++#
++# DCCP Configuration (EXPERIMENTAL)
++#
++# CONFIG_IP_DCCP is not set
++
++#
++# SCTP Configuration (EXPERIMENTAL)
++#
++CONFIG_IP_SCTP=m
++# CONFIG_SCTP_DBG_MSG is not set
++# CONFIG_SCTP_DBG_OBJCNT is not set
++# CONFIG_SCTP_HMAC_NONE is not set
++# CONFIG_SCTP_HMAC_SHA1 is not set
++CONFIG_SCTP_HMAC_MD5=y
++
++#
++# TIPC Configuration (EXPERIMENTAL)
++#
++# CONFIG_TIPC is not set
++# CONFIG_ATM is not set
++# CONFIG_BRIDGE is not set
++# CONFIG_VLAN_8021Q is not set
++# CONFIG_DECNET is not set
++# CONFIG_LLC2 is not set
++# CONFIG_IPX is not set
++# CONFIG_ATALK is not set
++# CONFIG_X25 is not set
++# CONFIG_LAPB is not set
++# CONFIG_ECONET is not set
++# CONFIG_WAN_ROUTER is not set
++
++#
++# QoS and/or fair queueing
++#
++# CONFIG_NET_SCHED is not set
++
++#
++# Network testing
++#
++# CONFIG_NET_PKTGEN is not set
++# CONFIG_HAMRADIO is not set
++# CONFIG_IRDA is not set
++# CONFIG_BT is not set
++# CONFIG_IEEE80211 is not set
++
++#
+ # Device Drivers
+ #
+ 
+@@ -173,13 +365,95 @@
+ #
+ CONFIG_STANDALONE=y
+ CONFIG_PREVENT_FIRMWARE_BUILD=y
+-# CONFIG_FW_LOADER is not set
+-CONFIG_DEBUG_DRIVER=y
++CONFIG_FW_LOADER=y
++# CONFIG_DEBUG_DRIVER is not set
++# CONFIG_DEBUG_DEVRES is not set
++# CONFIG_SYS_HYPERVISOR is not set
++
++#
++# Connector - unified userspace <-> kernelspace linker
++#
++# CONFIG_CONNECTOR is not set
+ 
+ #
+ # Memory Technology Devices (MTD)
+ #
+-# CONFIG_MTD is not set
++CONFIG_MTD=y
++# CONFIG_MTD_DEBUG is not set
++CONFIG_MTD_CONCAT=y
++CONFIG_MTD_PARTITIONS=y
++# CONFIG_MTD_REDBOOT_PARTS is not set
++CONFIG_MTD_CMDLINE_PARTS=y
++# CONFIG_MTD_AFS_PARTS is not set
++
++#
++# User Modules And Translation Layers
++#
++CONFIG_MTD_CHAR=y
++CONFIG_MTD_BLKDEVS=y
++CONFIG_MTD_BLOCK=y
++# CONFIG_FTL is not set
++# CONFIG_NFTL is not set
++# CONFIG_INFTL is not set
++# CONFIG_RFD_FTL is not set
++# CONFIG_SSFDC is not set
++
++#
++# RAM/ROM/Flash chip drivers
++#
++# CONFIG_MTD_CFI is not set
++# CONFIG_MTD_JEDECPROBE is not set
++CONFIG_MTD_MAP_BANK_WIDTH_1=y
++CONFIG_MTD_MAP_BANK_WIDTH_2=y
++CONFIG_MTD_MAP_BANK_WIDTH_4=y
++# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
++# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
++# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
++CONFIG_MTD_CFI_I1=y
++CONFIG_MTD_CFI_I2=y
++# CONFIG_MTD_CFI_I4 is not set
++# CONFIG_MTD_CFI_I8 is not set
++# CONFIG_MTD_RAM is not set
++# CONFIG_MTD_ROM is not set
++# CONFIG_MTD_ABSENT is not set
++# CONFIG_MTD_OBSOLETE_CHIPS is not set
++
++#
++# Mapping drivers for chip access
++#
++CONFIG_MTD_COMPLEX_MAPPINGS=y
++# CONFIG_MTD_PLATRAM is not set
++
++#
++# Self-contained MTD device drivers
++#
++# CONFIG_MTD_SLRAM is not set
++# CONFIG_MTD_PHRAM is not set
++# CONFIG_MTD_MTDRAM is not set
++# CONFIG_MTD_BLOCK2MTD is not set
++
++#
++# Disk-On-Chip Device Drivers
++#
++# CONFIG_MTD_DOC2000 is not set
++# CONFIG_MTD_DOC2001 is not set
++# CONFIG_MTD_DOC2001PLUS is not set
++
++#
++# NAND Flash Device Drivers
++#
++CONFIG_MTD_NAND=y
++# CONFIG_MTD_NAND_VERIFY_WRITE is not set
++# CONFIG_MTD_NAND_ECC_SMC is not set
++CONFIG_MTD_NAND_IDS=y
++# CONFIG_MTD_NAND_DISKONCHIP is not set
++CONFIG_MTD_NAND_AT91=y
++# CONFIG_MTD_NAND_NANDSIM is not set
++
++#
++# OneNAND Flash Device Drivers
++#
++# CONFIG_MTD_ONENAND is not set
+ 
+ #
+ # Parallel port support
+@@ -189,6 +463,7 @@
+ #
+ # Plug and Play support
+ #
++# CONFIG_PNPACPI is not set
+ 
+ #
+ # Block devices
+@@ -196,28 +471,27 @@
+ # CONFIG_BLK_DEV_COW_COMMON is not set
+ CONFIG_BLK_DEV_LOOP=y
+ # CONFIG_BLK_DEV_CRYPTOLOOP is not set
+-CONFIG_BLK_DEV_NBD=y
++# CONFIG_BLK_DEV_NBD is not set
+ # CONFIG_BLK_DEV_UB is not set
+ CONFIG_BLK_DEV_RAM=y
+ CONFIG_BLK_DEV_RAM_COUNT=16
+-CONFIG_BLK_DEV_RAM_SIZE=4096
+-CONFIG_BLK_DEV_INITRD=y
+-CONFIG_INITRAMFS_SOURCE=""
++CONFIG_BLK_DEV_RAM_SIZE=16384
++CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+ # CONFIG_CDROM_PKTCDVD is not set
++# CONFIG_ATA_OVER_ETH is not set
+ 
+ #
+-# IO Schedulers
++# ATA/ATAPI/MFM/RLL support
+ #
+-CONFIG_IOSCHED_NOOP=y
+-CONFIG_IOSCHED_AS=y
+-CONFIG_IOSCHED_DEADLINE=y
+-CONFIG_IOSCHED_CFQ=y
+-# CONFIG_ATA_OVER_ETH is not set
++# CONFIG_IDE is not set
+ 
+ #
+ # SCSI device support
+ #
++# CONFIG_RAID_ATTRS is not set
+ CONFIG_SCSI=y
++# CONFIG_SCSI_TGT is not set
++# CONFIG_SCSI_NETLINK is not set
+ CONFIG_SCSI_PROC_FS=y
+ 
+ #
+@@ -233,97 +507,61 @@
+ #
+ # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+ #
+-# CONFIG_SCSI_MULTI_LUN is not set
+-# CONFIG_SCSI_CONSTANTS is not set
+-# CONFIG_SCSI_LOGGING is not set
++CONFIG_SCSI_MULTI_LUN=y
++CONFIG_SCSI_CONSTANTS=y
++CONFIG_SCSI_LOGGING=y
++# CONFIG_SCSI_SCAN_ASYNC is not set
+ 
+ #
+-# SCSI Transport Attributes
++# SCSI Transports
+ #
+-# CONFIG_SCSI_SPI_ATTRS is not set
++CONFIG_SCSI_SPI_ATTRS=m
+ # CONFIG_SCSI_FC_ATTRS is not set
+ # CONFIG_SCSI_ISCSI_ATTRS is not set
++# CONFIG_SCSI_SAS_ATTRS is not set
++# CONFIG_SCSI_SAS_LIBSAS is not set
+ 
+ #
+ # SCSI low-level drivers
+ #
+-# CONFIG_SCSI_SATA is not set
++# CONFIG_ISCSI_TCP is not set
+ # CONFIG_SCSI_DEBUG is not set
+ 
+ #
+-# Multi-device support (RAID and LVM)
+-#
+-# CONFIG_MD is not set
+-
+-#
+-# Fusion MPT device support
++# PCMCIA SCSI adapter support
+ #
+-# CONFIG_FUSION is not set
++# CONFIG_PCMCIA_AHA152X is not set
++# CONFIG_PCMCIA_FDOMAIN is not set
++# CONFIG_PCMCIA_NINJA_SCSI is not set
++# CONFIG_PCMCIA_QLOGIC is not set
++# CONFIG_PCMCIA_SYM53C500 is not set
+ 
+ #
+-# IEEE 1394 (FireWire) support
++# Serial ATA (prod) and Parallel ATA (experimental) drivers
+ #
++# CONFIG_ATA is not set
+ 
+ #
+-# I2O device support
++# Multi-device support (RAID and LVM)
+ #
++# CONFIG_MD is not set
+ 
+ #
+-# Networking support
++# Fusion MPT device support
+ #
+-CONFIG_NET=y
++# CONFIG_FUSION is not set
+ 
+ #
+-# Networking options
++# IEEE 1394 (FireWire) support
+ #
+-CONFIG_PACKET=y
+-# CONFIG_PACKET_MMAP is not set
+-CONFIG_UNIX=y
+-# CONFIG_NET_KEY is not set
+-CONFIG_INET=y
+-CONFIG_IP_MULTICAST=y
+-# CONFIG_IP_ADVANCED_ROUTER is not set
+-CONFIG_IP_FIB_HASH=y
+-CONFIG_IP_PNP=y
+-CONFIG_IP_PNP_DHCP=y
+-# CONFIG_IP_PNP_BOOTP is not set
+-# CONFIG_IP_PNP_RARP is not set
+-# CONFIG_NET_IPIP is not set
+-# CONFIG_NET_IPGRE is not set
+-# CONFIG_IP_MROUTE is not set
+-# CONFIG_SYN_COOKIES is not set
+-# CONFIG_INET_AH is not set
+-# CONFIG_INET_ESP is not set
+-# CONFIG_INET_IPCOMP is not set
+-# CONFIG_INET_TUNNEL is not set
+-# CONFIG_IP_TCPDIAG is not set
+-# CONFIG_IP_TCPDIAG_IPV6 is not set
+-# CONFIG_TCP_CONG_ADVANCED is not set
+-CONFIG_TCP_CONG_BIC=y
+-# CONFIG_IPV6 is not set
+-# CONFIG_NETFILTER is not set
+-# CONFIG_BRIDGE is not set
+-# CONFIG_VLAN_8021Q is not set
+-# CONFIG_DECNET is not set
+-# CONFIG_LLC2 is not set
+-# CONFIG_IPX is not set
+-# CONFIG_ATALK is not set
+ 
+ #
+-# QoS and/or fair queueing
++# I2O device support
+ #
+-# CONFIG_NET_SCHED is not set
+-# CONFIG_NET_CLS_ROUTE is not set
+ 
+ #
+-# Network testing
++# Network device support
+ #
+-# CONFIG_NET_PKTGEN is not set
+-# CONFIG_NETPOLL is not set
+-# CONFIG_NET_POLL_CONTROLLER is not set
+-# CONFIG_HAMRADIO is not set
+-# CONFIG_IRDA is not set
+-# CONFIG_BT is not set
+ CONFIG_NETDEVICES=y
+ # CONFIG_DUMMY is not set
+ # CONFIG_BONDING is not set
+@@ -331,6 +569,11 @@
+ # CONFIG_TUN is not set
+ 
+ #
++# PHY device support
++#
++# CONFIG_PHYLIB is not set
++
++#
+ # Ethernet (10 or 100Mbit)
+ #
+ CONFIG_NET_ETHERNET=y
+@@ -357,11 +600,20 @@
+ # CONFIG_NET_RADIO is not set
+ 
+ #
++# PCMCIA network device support
++#
++# CONFIG_NET_PCMCIA is not set
++
++#
+ # Wan interfaces
+ #
+ # CONFIG_WAN is not set
+ # CONFIG_PPP is not set
+ # CONFIG_SLIP is not set
++# CONFIG_SHAPER is not set
++# CONFIG_NETCONSOLE is not set
++# CONFIG_NETPOLL is not set
++# CONFIG_NET_POLL_CONTROLLER is not set
+ 
+ #
+ # ISDN subsystem
+@@ -372,6 +624,7 @@
+ # Input device support
+ #
+ CONFIG_INPUT=y
++# CONFIG_INPUT_FF_MEMLESS is not set
+ 
+ #
+ # Userland interfaces
+@@ -397,9 +650,7 @@
+ #
+ # Hardware I/O ports
+ #
+-CONFIG_SERIO=y
+-# CONFIG_SERIO_SERPORT is not set
+-# CONFIG_SERIO_RAW is not set
++# CONFIG_SERIO is not set
+ # CONFIG_GAMEPORT is not set
+ 
+ #
+@@ -408,6 +659,7 @@
+ CONFIG_VT=y
+ CONFIG_VT_CONSOLE=y
+ CONFIG_HW_CONSOLE=y
++# CONFIG_VT_HW_CONSOLE_BINDING is not set
+ # CONFIG_SERIAL_NONSTANDARD is not set
+ 
+ #
+@@ -420,11 +672,11 @@
+ #
+ CONFIG_SERIAL_ATMEL=y
+ CONFIG_SERIAL_ATMEL_CONSOLE=y
++# CONFIG_SERIAL_ATMEL_TTYAT is not set
+ CONFIG_SERIAL_CORE=y
+ CONFIG_SERIAL_CORE_CONSOLE=y
+ CONFIG_UNIX98_PTYS=y
+-CONFIG_LEGACY_PTYS=y
+-CONFIG_LEGACY_PTY_COUNT=256
++# CONFIG_LEGACY_PTYS is not set
+ 
+ #
+ # IPMI
+@@ -435,21 +687,23 @@
+ # Watchdog Cards
+ #
+ # CONFIG_WATCHDOG is not set
++# CONFIG_HW_RANDOM is not set
+ # CONFIG_NVRAM is not set
+-# CONFIG_RTC is not set
+-# CONFIG_AT91RM9200_RTC is not set
+ # CONFIG_DTLK is not set
+ # CONFIG_R3964 is not set
+ 
+ #
+-# Ftape, the floppy tape device driver
++# PCMCIA character devices
+ #
++# CONFIG_SYNCLINK_CS is not set
++# CONFIG_CARDMAN_4000 is not set
++# CONFIG_CARDMAN_4040 is not set
+ # CONFIG_RAW_DRIVER is not set
+ 
+ #
+ # TPM devices
+ #
+-# CONFIG_AT91_SPI is not set
++# CONFIG_TCG_TPM is not set
+ 
+ #
+ # I2C support
+@@ -457,10 +711,50 @@
+ # CONFIG_I2C is not set
+ 
+ #
++# SPI support
++#
++# CONFIG_SPI is not set
++# CONFIG_SPI_MASTER is not set
++
++#
++# Dallas's 1-wire bus
++#
++# CONFIG_W1 is not set
++
++#
++# Hardware Monitoring support
++#
++CONFIG_HWMON=y
++# CONFIG_HWMON_VID is not set
++# CONFIG_SENSORS_ABITUGURU is not set
++# CONFIG_SENSORS_F71805F is not set
++# CONFIG_SENSORS_PC87427 is not set
++# CONFIG_SENSORS_VT1211 is not set
++CONFIG_HWMON_DEBUG_CHIP=y
++
++#
+ # Misc devices
+ #
+ 
+ #
++# Multifunction device drivers
++#
++# CONFIG_MFD_SM501 is not set
++
++#
++# LED devices
++#
++# CONFIG_NEW_LEDS is not set
++
++#
++# LED drivers
++#
++
++#
++# LED Triggers
++#
++
++#
+ # Multimedia devices
+ #
+ # CONFIG_VIDEO_DEV is not set
+@@ -469,17 +763,57 @@
+ # Digital Video Broadcasting Devices
+ #
+ # CONFIG_DVB is not set
++# CONFIG_USB_DABUSB is not set
+ 
+ #
+ # Graphics support
+ #
+-# CONFIG_FB is not set
++CONFIG_BACKLIGHT_LCD_SUPPORT=y
++CONFIG_BACKLIGHT_CLASS_DEVICE=y
++# CONFIG_LCD_CLASS_DEVICE is not set
++CONFIG_BACKLIGHT_KB920x=y
++CONFIG_FB=y
++# CONFIG_FIRMWARE_EDID is not set
++# CONFIG_FB_DDC is not set
++CONFIG_FB_CFB_FILLRECT=y
++CONFIG_FB_CFB_COPYAREA=y
++CONFIG_FB_CFB_IMAGEBLIT=y
++# CONFIG_FB_SVGALIB is not set
++# CONFIG_FB_MACMODES is not set
++# CONFIG_FB_BACKLIGHT is not set
++CONFIG_FB_MODE_HELPERS=y
++CONFIG_FB_TILEBLITTING=y
++
++#
++# Frame buffer hardware drivers
++#
++CONFIG_FB_S1D15605=y
++# CONFIG_FB_S1D13XXX is not set
++# CONFIG_FB_VIRTUAL is not set
+ 
+ #
+ # Console display driver support
+ #
+ # CONFIG_VGA_CONSOLE is not set
+ CONFIG_DUMMY_CONSOLE=y
++CONFIG_FRAMEBUFFER_CONSOLE=y
++# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
++CONFIG_FONTS=y
++# CONFIG_FONT_8x8 is not set
++# CONFIG_FONT_8x16 is not set
++# CONFIG_FONT_6x11 is not set
++# CONFIG_FONT_7x14 is not set
++# CONFIG_FONT_PEARL_8x8 is not set
++# CONFIG_FONT_ACORN_8x8 is not set
++CONFIG_FONT_MINI_4x6=y
++# CONFIG_FONT_SUN8x16 is not set
++# CONFIG_FONT_SUN12x22 is not set
++# CONFIG_FONT_10x18 is not set
++
++#
++# Logo configuration
++#
++# CONFIG_LOGO is not set
+ 
+ #
+ # Sound
+@@ -487,82 +821,98 @@
+ # CONFIG_SOUND is not set
+ 
+ #
++# HID Devices
++#
++CONFIG_HID=y
++# CONFIG_HID_DEBUG is not set
++
++#
+ # USB support
+ #
+ CONFIG_USB_ARCH_HAS_HCD=y
+ CONFIG_USB_ARCH_HAS_OHCI=y
++# CONFIG_USB_ARCH_HAS_EHCI is not set
+ CONFIG_USB=y
+-CONFIG_USB_DEBUG=y
++# CONFIG_USB_DEBUG is not set
+ 
+ #
+ # Miscellaneous USB options
+ #
+ CONFIG_USB_DEVICEFS=y
++# CONFIG_USB_DYNAMIC_MINORS is not set
++# CONFIG_USB_OTG is not set
+ 
+ #
+ # USB Host Controller Drivers
+ #
+ # CONFIG_USB_ISP116X_HCD is not set
+ CONFIG_USB_OHCI_HCD=y
+-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
++# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
++# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+ CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+ # CONFIG_USB_SL811_HCD is not set
+ 
+ #
+ # USB Device Class drivers
+ #
+-# CONFIG_USB_BLUETOOTH_TTY is not set
+ # CONFIG_USB_ACM is not set
+ # CONFIG_USB_PRINTER is not set
+ 
+ #
+-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
++# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
++#
++
++#
++# may also be needed; see USB_STORAGE Help for more information
+ #
+ CONFIG_USB_STORAGE=y
+-CONFIG_USB_STORAGE_DEBUG=y
++# CONFIG_USB_STORAGE_DEBUG is not set
++# CONFIG_USB_STORAGE_DATAFAB is not set
+ # CONFIG_USB_STORAGE_FREECOM is not set
+ # CONFIG_USB_STORAGE_DPCM is not set
++# CONFIG_USB_STORAGE_USBAT is not set
++# CONFIG_USB_STORAGE_SDDR09 is not set
++# CONFIG_USB_STORAGE_SDDR55 is not set
++# CONFIG_USB_STORAGE_JUMPSHOT is not set
++# CONFIG_USB_STORAGE_ALAUDA is not set
++# CONFIG_USB_STORAGE_KARMA is not set
++CONFIG_USB_LIBUSUAL=y
+ 
+ #
+ # USB Input Devices
+ #
+-# CONFIG_USB_HID is not set
+-
+-#
+-# USB HID Boot Protocol drivers
+-#
+-# CONFIG_USB_KBD is not set
+-# CONFIG_USB_MOUSE is not set
++CONFIG_USB_HID=y
++# CONFIG_USB_HIDINPUT_POWERBOOK is not set
++# CONFIG_HID_FF is not set
++# CONFIG_USB_HIDDEV is not set
+ # CONFIG_USB_AIPTEK is not set
+ # CONFIG_USB_WACOM is not set
+ # CONFIG_USB_ACECAD is not set
+ # CONFIG_USB_KBTAB is not set
+ # CONFIG_USB_POWERMATE is not set
+-# CONFIG_USB_MTOUCH is not set
+-# CONFIG_USB_ITMTOUCH is not set
+-# CONFIG_USB_EGALAX is not set
++# CONFIG_USB_TOUCHSCREEN is not set
++# CONFIG_USB_YEALINK is not set
+ # CONFIG_USB_XPAD is not set
+ # CONFIG_USB_ATI_REMOTE is not set
++# CONFIG_USB_ATI_REMOTE2 is not set
++# CONFIG_USB_KEYSPAN_REMOTE is not set
++# CONFIG_USB_APPLETOUCH is not set
++# CONFIG_USB_GTCO is not set
+ 
+ #
+ # USB Imaging devices
+ #
++# CONFIG_USB_MDC800 is not set
+ # CONFIG_USB_MICROTEK is not set
+ 
+ #
+-# USB Multimedia devices
+-#
+-# CONFIG_USB_DABUSB is not set
+-
+-#
+-# Video4Linux support is needed for USB Multimedia device support
+-#
+-
+-#
+ # USB Network Adapters
+ #
++# CONFIG_USB_CATC is not set
+ # CONFIG_USB_KAWETH is not set
+ # CONFIG_USB_PEGASUS is not set
++# CONFIG_USB_RTL8150 is not set
++# CONFIG_USB_USBNET_MII is not set
+ # CONFIG_USB_USBNET is not set
+ # CONFIG_USB_MON is not set
+ 
+@@ -580,12 +930,23 @@
+ #
+ # CONFIG_USB_EMI62 is not set
+ # CONFIG_USB_EMI26 is not set
++# CONFIG_USB_ADUTUX is not set
++# CONFIG_USB_AUERSWALD is not set
++# CONFIG_USB_RIO500 is not set
++# CONFIG_USB_LEGOTOWER is not set
+ # CONFIG_USB_LCD is not set
++# CONFIG_USB_BERRY_CHARGE is not set
+ # CONFIG_USB_LED is not set
++# CONFIG_USB_CYPRESS_CY7C63 is not set
+ # CONFIG_USB_CYTHERM is not set
+-# CONFIG_USB_PHIDGETKIT is not set
+-# CONFIG_USB_PHIDGETSERVO is not set
++# CONFIG_USB_PHIDGET is not set
+ # CONFIG_USB_IDMOUSE is not set
++# CONFIG_USB_FTDI_ELAN is not set
++# CONFIG_USB_APPLEDISPLAY is not set
++# CONFIG_USB_LD is not set
++# CONFIG_USB_TRANCEVIBRATOR is not set
++# CONFIG_USB_IOWARRIOR is not set
++# CONFIG_USB_TEST is not set
+ 
+ #
+ # USB DSL modem support
+@@ -599,36 +960,51 @@
+ #
+ # MMC/SD Card support
+ #
+-# CONFIG_MMC is not set
++CONFIG_MMC=y
++# CONFIG_MMC_DEBUG is not set
++CONFIG_MMC_BLOCK=y
++CONFIG_MMC_AT91=y
++
++#
++# Real Time Clock
++#
++CONFIG_RTC_LIB=y
++# CONFIG_RTC_CLASS is not set
+ 
+ #
+ # File systems
+ #
+ CONFIG_EXT2_FS=y
+ CONFIG_EXT2_FS_XATTR=y
+-# CONFIG_EXT2_FS_POSIX_ACL is not set
+-# CONFIG_EXT2_FS_SECURITY is not set
++CONFIG_EXT2_FS_POSIX_ACL=y
++CONFIG_EXT2_FS_SECURITY=y
+ # CONFIG_EXT2_FS_XIP is not set
+ CONFIG_EXT3_FS=y
+ CONFIG_EXT3_FS_XATTR=y
+-# CONFIG_EXT3_FS_POSIX_ACL is not set
+-# CONFIG_EXT3_FS_SECURITY is not set
++CONFIG_EXT3_FS_POSIX_ACL=y
++CONFIG_EXT3_FS_SECURITY=y
++# CONFIG_EXT4DEV_FS is not set
+ CONFIG_JBD=y
+ # CONFIG_JBD_DEBUG is not set
+ CONFIG_FS_MBCACHE=y
+ # CONFIG_REISERFS_FS is not set
+ # CONFIG_JFS_FS is not set
+-
+-#
+-# XFS support
+-#
++CONFIG_FS_POSIX_ACL=y
+ # CONFIG_XFS_FS is not set
++# CONFIG_GFS2_FS is not set
++# CONFIG_OCFS2_FS is not set
+ # CONFIG_MINIX_FS is not set
+ # CONFIG_ROMFS_FS is not set
+-# CONFIG_QUOTA is not set
++CONFIG_INOTIFY=y
++CONFIG_INOTIFY_USER=y
++CONFIG_QUOTA=y
++# CONFIG_QFMT_V1 is not set
++CONFIG_QFMT_V2=y
++CONFIG_QUOTACTL=y
+ CONFIG_DNOTIFY=y
+-CONFIG_AUTOFS_FS=y
++# CONFIG_AUTOFS_FS is not set
+ CONFIG_AUTOFS4_FS=y
++# CONFIG_FUSE_FS is not set
+ 
+ #
+ # CD-ROM/DVD Filesystems
+@@ -643,25 +1019,40 @@
+ CONFIG_MSDOS_FS=y
+ CONFIG_VFAT_FS=y
+ CONFIG_FAT_DEFAULT_CODEPAGE=437
+-CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
++CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
+ # CONFIG_NTFS_FS is not set
+ 
+ #
+ # Pseudo filesystems
+ #
+ CONFIG_PROC_FS=y
++CONFIG_PROC_SYSCTL=y
+ CONFIG_SYSFS=y
+-CONFIG_DEVPTS_FS_XATTR=y
+-# CONFIG_DEVPTS_FS_SECURITY is not set
+ CONFIG_TMPFS=y
+-# CONFIG_TMPFS_XATTR is not set
++# CONFIG_TMPFS_POSIX_ACL is not set
+ # CONFIG_HUGETLB_PAGE is not set
+ CONFIG_RAMFS=y
++CONFIG_CONFIGFS_FS=y
+ 
+ #
+ # Miscellaneous filesystems
+ #
++# CONFIG_ADFS_FS is not set
++# CONFIG_AFFS_FS is not set
++# CONFIG_HFS_FS is not set
+ # CONFIG_HFSPLUS_FS is not set
++# CONFIG_BEFS_FS is not set
++# CONFIG_BFS_FS is not set
++# CONFIG_EFS_FS is not set
++CONFIG_JFFS2_FS=y
++CONFIG_JFFS2_FS_DEBUG=0
++CONFIG_JFFS2_FS_WRITEBUFFER=y
++# CONFIG_JFFS2_SUMMARY is not set
++# CONFIG_JFFS2_FS_XATTR is not set
++# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
++CONFIG_JFFS2_ZLIB=y
++CONFIG_JFFS2_RTIME=y
++# CONFIG_JFFS2_RUBIN is not set
+ # CONFIG_CRAMFS is not set
+ # CONFIG_VXFS_FS is not set
+ # CONFIG_HPFS_FS is not set
+@@ -675,16 +1066,23 @@
+ CONFIG_NFS_FS=y
+ CONFIG_NFS_V3=y
+ # CONFIG_NFS_V3_ACL is not set
++CONFIG_NFS_V4=y
++# CONFIG_NFS_DIRECTIO is not set
+ # CONFIG_NFSD is not set
+ CONFIG_ROOT_NFS=y
+ CONFIG_LOCKD=y
+ CONFIG_LOCKD_V4=y
+ CONFIG_NFS_COMMON=y
+ CONFIG_SUNRPC=y
++CONFIG_SUNRPC_GSS=y
++CONFIG_RPCSEC_GSS_KRB5=y
++# CONFIG_RPCSEC_GSS_SPKM3 is not set
+ # CONFIG_SMB_FS is not set
+ # CONFIG_CIFS is not set
+ # CONFIG_NCP_FS is not set
+ # CONFIG_CODA_FS is not set
++# CONFIG_AFS_FS is not set
++# CONFIG_9P_FS is not set
+ 
+ #
+ # Partition Types
+@@ -734,26 +1132,51 @@
+ # CONFIG_NLS_ISO8859_15 is not set
+ # CONFIG_NLS_KOI8_R is not set
+ # CONFIG_NLS_KOI8_U is not set
+-# CONFIG_NLS_UTF8 is not set
++CONFIG_NLS_UTF8=y
++
++#
++# Distributed Lock Manager
++#
++# CONFIG_DLM is not set
++
++#
++# Profiling support
++#
++# CONFIG_PROFILING is not set
+ 
+ #
+ # Kernel hacking
+ #
+ # CONFIG_PRINTK_TIME is not set
++CONFIG_ENABLE_MUST_CHECK=y
++CONFIG_MAGIC_SYSRQ=y
++# CONFIG_UNUSED_SYMBOLS is not set
++# CONFIG_DEBUG_FS is not set
++# CONFIG_HEADERS_CHECK is not set
+ CONFIG_DEBUG_KERNEL=y
+-# CONFIG_MAGIC_SYSRQ is not set
+-CONFIG_LOG_BUF_SHIFT=14
++# CONFIG_DEBUG_SHIRQ is not set
++CONFIG_LOG_BUF_SHIFT=17
++CONFIG_DETECT_SOFTLOCKUP=y
+ # CONFIG_SCHEDSTATS is not set
++# CONFIG_TIMER_STATS is not set
+ # CONFIG_DEBUG_SLAB is not set
+-# CONFIG_DEBUG_SPINLOCK is not set
+-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
++# CONFIG_DEBUG_RT_MUTEXES is not set
++# CONFIG_RT_MUTEX_TESTER is not set
++CONFIG_DEBUG_SPINLOCK=y
++# CONFIG_DEBUG_MUTEXES is not set
++CONFIG_DEBUG_SPINLOCK_SLEEP=y
++# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+ # CONFIG_DEBUG_KOBJECT is not set
+ CONFIG_DEBUG_BUGVERBOSE=y
+ # CONFIG_DEBUG_INFO is not set
+-# CONFIG_DEBUG_FS is not set
++# CONFIG_DEBUG_VM is not set
++# CONFIG_DEBUG_LIST is not set
+ CONFIG_FRAME_POINTER=y
+-CONFIG_DEBUG_USER=y
+-CONFIG_DEBUG_ERRORS=y
++CONFIG_FORCED_INLINING=y
++# CONFIG_RCU_TORTURE_TEST is not set
++# CONFIG_FAULT_INJECTION is not set
++# CONFIG_DEBUG_USER is not set
++# CONFIG_DEBUG_ERRORS is not set
+ CONFIG_DEBUG_LL=y
+ # CONFIG_DEBUG_ICEDCC is not set
+ 
+@@ -766,7 +1189,43 @@
+ #
+ # Cryptographic options
+ #
+-# CONFIG_CRYPTO is not set
++CONFIG_CRYPTO=y
++CONFIG_CRYPTO_ALGAPI=y
++CONFIG_CRYPTO_BLKCIPHER=y
++CONFIG_CRYPTO_HASH=m
++CONFIG_CRYPTO_MANAGER=y
++CONFIG_CRYPTO_HMAC=m
++# CONFIG_CRYPTO_XCBC is not set
++# CONFIG_CRYPTO_NULL is not set
++# CONFIG_CRYPTO_MD4 is not set
++CONFIG_CRYPTO_MD5=y
++# CONFIG_CRYPTO_SHA1 is not set
++# CONFIG_CRYPTO_SHA256 is not set
++# CONFIG_CRYPTO_SHA512 is not set
++# CONFIG_CRYPTO_WP512 is not set
++# CONFIG_CRYPTO_TGR192 is not set
++# CONFIG_CRYPTO_GF128MUL is not set
++# CONFIG_CRYPTO_ECB is not set
++CONFIG_CRYPTO_CBC=y
++CONFIG_CRYPTO_PCBC=m
++# CONFIG_CRYPTO_LRW is not set
++CONFIG_CRYPTO_DES=y
++# CONFIG_CRYPTO_FCRYPT is not set
++# CONFIG_CRYPTO_BLOWFISH is not set
++# CONFIG_CRYPTO_TWOFISH is not set
++# CONFIG_CRYPTO_SERPENT is not set
++# CONFIG_CRYPTO_AES is not set
++# CONFIG_CRYPTO_CAST5 is not set
++# CONFIG_CRYPTO_CAST6 is not set
++# CONFIG_CRYPTO_TEA is not set
++# CONFIG_CRYPTO_ARC4 is not set
++# CONFIG_CRYPTO_KHAZAD is not set
++# CONFIG_CRYPTO_ANUBIS is not set
++# CONFIG_CRYPTO_DEFLATE is not set
++# CONFIG_CRYPTO_MICHAEL_MIC is not set
++# CONFIG_CRYPTO_CRC32C is not set
++# CONFIG_CRYPTO_CAMELLIA is not set
++# CONFIG_CRYPTO_TEST is not set
+ 
+ #
+ # Hardware crypto devices
+@@ -775,6 +1234,14 @@
+ #
+ # Library routines
+ #
++CONFIG_BITREVERSE=y
+ # CONFIG_CRC_CCITT is not set
++# CONFIG_CRC16 is not set
+ CONFIG_CRC32=y
+ # CONFIG_LIBCRC32C is not set
++CONFIG_AUDIT_GENERIC=y
++CONFIG_ZLIB_INFLATE=y
++CONFIG_ZLIB_DEFLATE=y
++CONFIG_PLIST=y
++CONFIG_HAS_IOMEM=y
++CONFIG_HAS_IOPORT=y
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91rm9200.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91rm9200.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91rm9200.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91rm9200.c	2007-07-29 05:23:04.000000000 +0200
+@@ -267,6 +267,33 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91rm9200_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91RM9200_BASE_TCB0,
++		.irq		= { AT91RM9200_ID_TC0, AT91RM9200_ID_TC1, AT91RM9200_ID_TC2 },
++		.clk		= { &tc0_clk, &tc1_clk, &tc2_clk },
++	},
++	[1] = {
++		.physaddr	= AT91RM9200_BASE_TCB1,
++		.irq		= { AT91RM9200_ID_TC3, AT91RM9200_ID_TC4, AT91RM9200_ID_TC5 },
++		.clk		= { &tc3_clk, &tc4_clk, &tc5_clk },
++	},
++};
++
++#define at91rm9200_tc_init()	atmel_tc_init(at91rm9200_tcblocks, ARRAY_SIZE(at91rm9200_tcblocks))
++
++#else
++#define at91rm9200_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91RM9200 processor initialization
+  * -------------------------------------------------------------------- */
+ void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks)
+@@ -288,6 +315,9 @@
+ 
+ 	/* Initialize GPIO subsystem */
+ 	at91_gpio_init(at91rm9200_gpio, banks);
++
++	/* Initialize the Timer/Counter blocks */
++	at91rm9200_tc_init();
+ }
+ 
+ 
+@@ -301,28 +331,28 @@
+ static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
+ 	7,	/* Advanced Interrupt Controller (FIQ) */
+ 	7,	/* System Peripherals */
+-	0,	/* Parallel IO Controller A */
+-	0,	/* Parallel IO Controller B */
+-	0,	/* Parallel IO Controller C */
+-	0,	/* Parallel IO Controller D */
+-	6,	/* USART 0 */
+-	6,	/* USART 1 */
+-	6,	/* USART 2 */
+-	6,	/* USART 3 */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C */
++	1,	/* Parallel IO Controller D */
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
++	5,	/* USART 3 */
+ 	0,	/* Multimedia Card Interface */
+-	4,	/* USB Device Port */
+-	0,	/* Two-Wire Interface */
+-	6,	/* Serial Peripheral Interface */
+-	5,	/* Serial Synchronous Controller 0 */
+-	5,	/* Serial Synchronous Controller 1 */
+-	5,	/* Serial Synchronous Controller 2 */
++	2,	/* USB Device Port */
++	6,	/* Two-Wire Interface */
++	5,	/* Serial Peripheral Interface */
++	4,	/* Serial Synchronous Controller 0 */
++	4,	/* Serial Synchronous Controller 1 */
++	4,	/* Serial Synchronous Controller 2 */
+ 	0,	/* Timer Counter 0 */
+ 	0,	/* Timer Counter 1 */
+ 	0,	/* Timer Counter 2 */
+ 	0,	/* Timer Counter 3 */
+ 	0,	/* Timer Counter 4 */
+ 	0,	/* Timer Counter 5 */
+-	3,	/* USB Host port */
++	2,	/* USB Host port */
+ 	3,	/* Ethernet MAC */
+ 	0,	/* Advanced Interrupt Controller (IRQ0) */
+ 	0,	/* Advanced Interrupt Controller (IRQ1) */
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91rm9200_devices.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91rm9200_devices.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91rm9200_devices.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91rm9200_devices.c	2007-07-29 05:23:04.000000000 +0200
+@@ -477,7 +477,18 @@
+  *  SPI
+  * -------------------------------------------------------------------- */
+ 
+-#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)
++#if defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)		/* legacy SPI driver */
++#define SPI_DEVNAME	"at91_spi"
++
++#elif defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE)	/* SPI bitbanging driver */
++#define SPI_DEVNAME	"at91_spi"
++
++#elif defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)	/* new SPI driver */
++#define SPI_DEVNAME	"atmel_spi"
++
++#endif
++
++#ifdef SPI_DEVNAME
+ static u64 spi_dmamask = 0xffffffffUL;
+ 
+ static struct resource spi_resources[] = {
+@@ -494,7 +505,7 @@
+ };
+ 
+ static struct platform_device at91rm9200_spi_device = {
+-	.name		= "at91_spi",
++	.name		= SPI_DEVNAME,
+ 	.id		= 0,
+ 	.dev		= {
+ 				.dma_mask		= &spi_dmamask,
+@@ -603,6 +614,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9260.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9260.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9260.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9260.c	2007-07-29 05:23:04.000000000 +0200
+@@ -269,6 +269,33 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91sam9260_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91SAM9260_BASE_TCB0,
++		.irq		= { AT91SAM9260_ID_TC0, AT91SAM9260_ID_TC1, AT91SAM9260_ID_TC2 },
++		.clk		= { &tc0_clk, &tc1_clk, &tc2_clk },
++	},
++	[1] = {
++		.physaddr	= AT91SAM9260_BASE_TCB1,
++		.irq		= { AT91SAM9260_ID_TC3, AT91SAM9260_ID_TC4, AT91SAM9260_ID_TC5 },
++		.clk		= { &tc3_clk, &tc4_clk, &tc5_clk },
++	},
++};
++
++#define at91sam9260_tc_init()	atmel_tc_init(at91sam9260_tcblocks, ARRAY_SIZE(at91sam9260_tcblocks))
++
++#else
++#define at91sam9260_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91SAM9260 processor initialization
+  * -------------------------------------------------------------------- */
+ 
+@@ -315,6 +342,9 @@
+ 
+ 	/* Register GPIO subsystem */
+ 	at91_gpio_init(at91sam9260_gpio, 3);
++
++	/* Initialize the Timer/Counter blocks */
++	at91sam9260_tc_init();
+ }
+ 
+ /* --------------------------------------------------------------------
+@@ -327,30 +357,30 @@
+ static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = {
+ 	7,	/* Advanced Interrupt Controller */
+ 	7,	/* System Peripherals */
+-	0,	/* Parallel IO Controller A */
+-	0,	/* Parallel IO Controller B */
+-	0,	/* Parallel IO Controller C */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C */
+ 	0,	/* Analog-to-Digital Converter */
+-	6,	/* USART 0 */
+-	6,	/* USART 1 */
+-	6,	/* USART 2 */
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
+ 	0,	/* Multimedia Card Interface */
+-	4,	/* USB Device Port */
+-	0,	/* Two-Wire Interface */
+-	6,	/* Serial Peripheral Interface 0 */
+-	6,	/* Serial Peripheral Interface 1 */
++	2,	/* USB Device Port */
++	6,	/* Two-Wire Interface */
++	5,	/* Serial Peripheral Interface 0 */
++	5,	/* Serial Peripheral Interface 1 */
+ 	5,	/* Serial Synchronous Controller */
+ 	0,
+ 	0,
+ 	0,	/* Timer Counter 0 */
+ 	0,	/* Timer Counter 1 */
+ 	0,	/* Timer Counter 2 */
+-	3,	/* USB Host port */
++	2,	/* USB Host port */
+ 	3,	/* Ethernet */
+ 	0,	/* Image Sensor Interface */
+-	6,	/* USART 3 */
+-	6,	/* USART 4 */
+-	6,	/* USART 5 */
++	5,	/* USART 3 */
++	5,	/* USART 4 */
++	5,	/* USART 5 */
+ 	0,	/* Timer Counter 3 */
+ 	0,	/* Timer Counter 4 */
+ 	0,	/* Timer Counter 5 */
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9260_devices.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9260_devices.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9260_devices.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9260_devices.c	2007-07-29 05:23:04.000000000 +0200
+@@ -524,6 +524,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9261.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9261.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9261.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9261.c	2007-07-29 05:23:04.000000000 +0200
+@@ -247,6 +247,28 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91sam9261_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91SAM9261_BASE_TCB0,
++		.irq		= { AT91SAM9261_ID_TC0, AT91SAM9261_ID_TC1, AT91SAM9261_ID_TC2 },
++		.clk		= { &tc0_clk, &tc1_clk, &tc2_clk },
++	}
++};
++
++#define at91sam9261_tc_init()	atmel_tc_init(at91sam9261_tcblocks, ARRAY_SIZE(at91sam9261_tcblocks))
++
++#else
++#define at91sam9261_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91SAM9261 processor initialization
+  * -------------------------------------------------------------------- */
+ 
+@@ -267,6 +289,9 @@
+ 
+ 	/* Register GPIO subsystem */
+ 	at91_gpio_init(at91sam9261_gpio, 3);
++
++	/* Initialize the Timer/Counter blocks */
++	at91sam9261_tc_init();
+ }
+ 
+ /* --------------------------------------------------------------------
+@@ -279,25 +304,25 @@
+ static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = {
+ 	7,	/* Advanced Interrupt Controller */
+ 	7,	/* System Peripherals */
+-	0,	/* Parallel IO Controller A */
+-	0,	/* Parallel IO Controller B */
+-	0,	/* Parallel IO Controller C */
+-	0,
+-	6,	/* USART 0 */
+-	6,	/* USART 1 */
+-	6,	/* USART 2 */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C */
++	0,
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
+ 	0,	/* Multimedia Card Interface */
+-	4,	/* USB Device Port */
+-	0,	/* Two-Wire Interface */
+-	6,	/* Serial Peripheral Interface 0 */
+-	6,	/* Serial Peripheral Interface 1 */
+-	5,	/* Serial Synchronous Controller 0 */
+-	5,	/* Serial Synchronous Controller 1 */
+-	5,	/* Serial Synchronous Controller 2 */
++	2,	/* USB Device Port */
++	6,	/* Two-Wire Interface */
++	5,	/* Serial Peripheral Interface 0 */
++	5,	/* Serial Peripheral Interface 1 */
++	4,	/* Serial Synchronous Controller 0 */
++	4,	/* Serial Synchronous Controller 1 */
++	4,	/* Serial Synchronous Controller 2 */
+ 	0,	/* Timer Counter 0 */
+ 	0,	/* Timer Counter 1 */
+ 	0,	/* Timer Counter 2 */
+-	3,	/* USB Host port */
++	2,	/* USB Host port */
+ 	3,	/* LCD Controller */
+ 	0,
+ 	0,
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9261_devices.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9261_devices.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9261_devices.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9261_devices.c	2007-07-29 05:23:04.000000000 +0200
+@@ -14,6 +14,9 @@
+ #include <asm/mach/map.h>
+ 
+ #include <linux/platform_device.h>
++#include <linux/fb.h>
++
++#include <video/atmel_lcdc.h>
+ 
+ #include <asm/arch/board.h>
+ #include <asm/arch/gpio.h>
+@@ -522,6 +525,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9263.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9263.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9263.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9263.c	2007-07-29 05:23:04.000000000 +0200
+@@ -273,6 +273,28 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91sam9263_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91SAM9263_BASE_TCB0,
++		.irq		= { AT91SAM9263_ID_TCB, AT91SAM9263_ID_TCB, AT91SAM9263_ID_TCB },
++		.clk		= { &tcb_clk, &tcb_clk, &tcb_clk },
++	}
++};
++
++#define at91sam9263_tc_init()	atmel_tc_init(at91sam9263_tcblocks, ARRAY_SIZE(at91sam9263_tcblocks))
++
++#else
++#define at91sam9263_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91SAM9263 processor initialization
+  * -------------------------------------------------------------------- */
+ 
+@@ -292,6 +314,9 @@
+ 
+ 	/* Register GPIO subsystem */
+ 	at91_gpio_init(at91sam9263_gpio, 5);
++
++	/* Initialize the Timer/Counter blocks */
++	at91sam9263_tc_init();
+ }
+ 
+ /* --------------------------------------------------------------------
+@@ -304,34 +329,34 @@
+ static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
+ 	7,	/* Advanced Interrupt Controller (FIQ) */
+ 	7,	/* System Peripherals */
+-	0,	/* Parallel IO Controller A */
+-	0,	/* Parallel IO Controller B */
+-	0,	/* Parallel IO Controller C, D and E */
++	1,	/* Parallel IO Controller A */
++	1,	/* Parallel IO Controller B */
++	1,	/* Parallel IO Controller C, D and E */
+ 	0,
+ 	0,
+-	6,	/* USART 0 */
+-	6,	/* USART 1 */
+-	6,	/* USART 2 */
++	5,	/* USART 0 */
++	5,	/* USART 1 */
++	5,	/* USART 2 */
+ 	0,	/* Multimedia Card Interface 0 */
+ 	0,	/* Multimedia Card Interface 1 */
+-	4,	/* CAN */
+-	0,	/* Two-Wire Interface */
+-	6,	/* Serial Peripheral Interface 0 */
+-	6,	/* Serial Peripheral Interface 1 */
+-	5,	/* Serial Synchronous Controller 0 */
+-	5,	/* Serial Synchronous Controller 1 */
+-	6,	/* AC97 Controller */
++	3,	/* CAN */
++	6,	/* Two-Wire Interface */
++	5,	/* Serial Peripheral Interface 0 */
++	5,	/* Serial Peripheral Interface 1 */
++	4,	/* Serial Synchronous Controller 0 */
++	4,	/* Serial Synchronous Controller 1 */
++	5,	/* AC97 Controller */
+ 	0,	/* Timer Counter 0, 1 and 2 */
+ 	0,	/* Pulse Width Modulation Controller */
+ 	3,	/* Ethernet */
+ 	0,
+ 	0,	/* 2D Graphic Engine */
+-	3,	/* USB Device Port */
++	2,	/* USB Device Port */
+ 	0,	/* Image Sensor Interface */
+ 	3,	/* LDC Controller */
+ 	0,	/* DMA Controller */
+ 	0,
+-	3,	/* USB Host port */
++	2,	/* USB Host port */
+ 	0,	/* Advanced Interrupt Controller (IRQ0) */
+ 	0,	/* Advanced Interrupt Controller (IRQ1) */
+ };
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9263_devices.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9263_devices.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9263_devices.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9263_devices.c	2007-07-29 05:23:04.000000000 +0200
+@@ -13,6 +13,9 @@
+ #include <asm/mach/map.h>
+ 
+ #include <linux/platform_device.h>
++#include <linux/fb.h>
++
++#include <video/atmel_lcdc.h>
+ 
+ #include <asm/arch/board.h>
+ #include <asm/arch/gpio.h>
+@@ -625,6 +628,56 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Image Sensor Interface
++ * -------------------------------------------------------------------- */
++
++#if defined(CONFIG_VIDEO_AT91_ISI) || defined(CONFIG_VIDEO_AT91_ISI_MODULE)
++
++struct resource isi_resources[] = {
++	[0] = {
++		.start	= AT91SAM9263_BASE_ISI,
++		.end	= AT91SAM9263_BASE_ISI + SZ_16K - 1,
++		.flags	= IORESOURCE_MEM,
++	},
++	[1] = {
++		.start	= AT91SAM9263_ID_ISI,
++		.end	= AT91SAM9263_ID_ISI,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device at91sam9263_isi_device = {
++	.name		= "at91_isi",
++	.id		= -1,
++	.resource	= isi_resources,
++	.num_resources	= ARRAY_SIZE(isi_resources),
++};
++
++void __init at91_add_device_isi(void)
++{
++	at91_set_A_periph(AT91_PIN_PE0, 0);	/* ISI_D0 */
++	at91_set_A_periph(AT91_PIN_PE1, 0);	/* ISI_D1 */
++	at91_set_A_periph(AT91_PIN_PE2, 0);	/* ISI_D2 */
++	at91_set_A_periph(AT91_PIN_PE3, 0);	/* ISI_D3 */
++	at91_set_A_periph(AT91_PIN_PE4, 0);	/* ISI_D4 */
++	at91_set_A_periph(AT91_PIN_PE5, 0);	/* ISI_D5 */
++	at91_set_A_periph(AT91_PIN_PE6, 0);	/* ISI_D6 */
++	at91_set_A_periph(AT91_PIN_PE7, 0);	/* ISI_D7 */
++	at91_set_A_periph(AT91_PIN_PE8, 0);	/* ISI_PCK */
++	at91_set_A_periph(AT91_PIN_PE9, 0);	/* ISI_HSYNC */
++	at91_set_A_periph(AT91_PIN_PE10, 0);	/* ISI_VSYNC */
++	at91_set_B_periph(AT91_PIN_PE11, 0);	/* ISI_MCK (PCK3) */
++	at91_set_B_periph(AT91_PIN_PE12, 0);	/* ISI_PD8 */
++	at91_set_B_periph(AT91_PIN_PE13, 0);	/* ISI_PD9 */
++	at91_set_B_periph(AT91_PIN_PE14, 0);	/* ISI_PD10 */
++	at91_set_B_periph(AT91_PIN_PE15, 0);	/* ISI_PD11 */
++}
++#else
++void __init at91_add_device_isi(void) {}
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  LCD Controller
+  * -------------------------------------------------------------------- */
+ 
+@@ -715,6 +768,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9rl.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9rl.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9rl.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9rl.c	2007-07-29 05:23:04.000000000 +0200
+@@ -246,6 +246,28 @@
+ 
+ 
+ /* --------------------------------------------------------------------
++ *  Timer/Counter library initialization
++ * -------------------------------------------------------------------- */
++#ifdef CONFIG_ATMEL_TCLIB
++
++#include "tclib.h"
++
++static struct atmel_tcblock at91sam9rl_tcblocks[] = {
++	[0] = {
++		.physaddr	= AT91SAM9RL_BASE_TCB0,
++		.irq		= { AT91SAM9RL_ID_TC0, AT91SAM9RL_ID_TC1, AT91SAM9RL_ID_TC2 },
++		.clk		= { &tc0_clk, &tc1_clk, &tc2_clk },
++	}
++};
++
++#define at91sam9rl_tc_init()	atmel_tc_init(at91sam9rl_tcblocks, ARRAY_SIZE(at91sam9rl_tcblocks))
++
++#else
++#define at91sam9rl_tc_init()	do {} while(0)
++#endif
++
++
++/* --------------------------------------------------------------------
+  *  AT91SAM9RL processor initialization
+  * -------------------------------------------------------------------- */
+ 
+@@ -284,6 +306,9 @@
+ 
+ 	/* Register GPIO subsystem */
+ 	at91_gpio_init(at91sam9rl_gpio, 4);
++	
++	/* Initialize the Timer/Counter blocks */
++	at91sam9rl_tc_init();
+ }
+ 
+ /* --------------------------------------------------------------------
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9rl_devices.c linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9rl_devices.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/at91sam9rl_devices.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/at91sam9rl_devices.c	2007-07-29 05:23:04.000000000 +0200
+@@ -370,6 +370,32 @@
+ #endif
+ 
+ 
++#if defined(CONFIG_NEW_LEDS)
++
++static struct platform_device at91_leds = {
++	.name		= "at91_leds",
++	.id		= -1,
++};
++
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
++{
++	if (!nr)
++		return;
++
++	at91_leds.dev.platform_data = leds;
++
++	for ( ; nr; nr--, leds++) {
++		leds->index = nr;	/* first record stores number of leds */
++		at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
++	}
++
++	platform_device_register(&at91_leds);
++}
++#else
++void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
++#endif
++
++
+ /* --------------------------------------------------------------------
+  *  UART
+  * -------------------------------------------------------------------- */
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/board-cam60.c linux-2.6.22-rc5.new/arch/arm/mach-at91/board-cam60.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/board-cam60.c	1970-01-01 01:00:00.000000000 +0100
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/board-cam60.c	2007-07-29 05:23:04.000000000 +0200
+@@ -0,0 +1,148 @@
++/*
++ * KwikByte CAM60
++ *
++ * based on board-sam9260ek.c
++ *   Copyright (C) 2005 SAN People
++ *   Copyright (C) 2006 Atmel
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++
++#include <linux/types.h>
++#include <linux/init.h>
++#include <linux/mm.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/spi/spi.h>
++#include <linux/spi/flash.h>
++
++#include <asm/hardware.h>
++#include <asm/setup.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/mach/irq.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++#include <asm/arch/at91sam926x_mc.h>
++
++#include "generic.h"
++
++
++/*
++ * Serial port configuration.
++ *    0 .. 5 = USART0 .. USART5
++ *    6      = DBGU
++ */
++static struct at91_uart_config __initdata cam60_uart_config = {
++	.console_tty	= 0,				/* ttyS0 */
++	.nr_tty		= 1,
++	.tty_map	= { 6, -1, -1, -1, -1, -1, -1 }	/* ttyS0, ..., ttyS6 */
++};
++
++static void __init cam60_map_io(void)
++{
++	/* Initialize processor: 10 MHz crystal */
++	at91sam9260_initialize(10000000);
++
++	/* Setup the serial ports and console */
++	at91_init_serial(&cam60_uart_config);
++}
++
++static void __init cam60_init_irq(void)
++{
++	at91sam9260_init_interrupts(NULL);
++}
++
++
++/*
++ * SPI devices.
++ */
++#if defined(CONFIG_MTD_DATAFLASH)
++static struct mtd_partition __initdata cam60_spi_partitions[] = {
++	{
++		.name	= "BOOT1",
++		.offset	= 0,
++		.size	= 4 * 1056,
++	},
++	{
++		.name	= "BOOT2",
++		.offset	= MTDPART_OFS_NXTBLK,
++		.size	= 256 * 1056,
++	},
++	{
++		.name	= "kernel",
++		.offset	= MTDPART_OFS_NXTBLK,
++		.size	= 2222 * 1056,
++	},
++	{
++		.name	= "file system",
++		.offset	= MTDPART_OFS_NXTBLK,
++		.size	= MTDPART_SIZ_FULL,
++	},
++};
++
++static struct flash_platform_data __initdata cam60_spi_flash_platform_data = {
++	.name		= "spi_flash",
++	.parts		= cam60_spi_partitions,
++	.nr_parts	= ARRAY_SIZE(cam60_spi_partitions)
++};
++#endif
++
++static struct spi_board_info cam60_spi_devices[] = {
++#if defined(CONFIG_MTD_DATAFLASH)
++	{	/* DataFlash chip */
++		.modalias	= "mtd_dataflash",
++		.chip_select	= 0,
++		.max_speed_hz	= 15 * 1000 * 1000,
++		.bus_num	= 0,
++		.platform_data	= &cam60_spi_flash_platform_data
++	},
++#endif
++};
++
++
++/*
++ * MACB Ethernet device
++ */
++static struct __initdata at91_eth_data cam60_macb_data = {
++	.phy_irq_pin	= AT91_PIN_PB5,
++	.is_rmii	= 0,
++};
++
++
++static void __init cam60_board_init(void)
++{
++	/* Serial */
++	at91_add_device_serial();
++	/* SPI */
++	at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices));
++	/* Ethernet */
++	at91_add_device_eth(&cam60_macb_data);
++}
++
++MACHINE_START(CAM60, "KwikByte CAM60")
++	/* Maintainer: KwikByte */
++	.phys_io	= AT91_BASE_SYS,
++	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
++	.boot_params	= AT91_SDRAM_BASE + 0x100,
++	.timer		= &at91sam926x_timer,
++	.map_io		= cam60_map_io,
++	.init_irq	= cam60_init_irq,
++	.init_machine	= cam60_board_init,
++MACHINE_END
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/board-chub.c linux-2.6.22-rc5.new/arch/arm/mach-at91/board-chub.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/board-chub.c	1970-01-01 01:00:00.000000000 +0100
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/board-chub.c	2007-07-29 05:23:04.000000000 +0200
+@@ -0,0 +1,132 @@
++/*
++ * linux/arch/arm/mach-at91/board-chub.c
++ *
++ *  Copyright (C) 2005 SAN People, adapted for Promwad Chub board
++ *  by Kuten Ivan
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
++ */
++
++#include <linux/types.h>
++#include <linux/init.h>
++#include <linux/mm.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++
++#include <asm/hardware.h>
++#include <asm/setup.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/mach/irq.h>
++
++#include <asm/arch/board.h>
++#include <asm/arch/gpio.h>
++
++#include "generic.h"
++
++/*
++ * Serial port configuration.
++ *    0 .. 3 = USART0 .. USART3
++ *    4      = DBGU
++ */
++static struct at91_uart_config __initdata chub_uart_config = {
++	.console_tty	= 0,				/* ttyS0 */
++	.nr_tty		= 5,
++	.tty_map	= { 4, 0, 1, 2, 3 }		/* ttyS0, ..., ttyS4 */
++};
++
++static void __init chub_init_irq(void)
++{
++	at91rm9200_init_interrupts(NULL);
++}
++
++static void __init chub_map_io(void)
++{
++	/* Initialize clocks: 18.432 MHz crystal */
++	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
++
++	/* Setup the serial ports and console */
++	at91_init_serial(&chub_uart_config);
++}
++
++static struct at91_eth_data __initdata chub_eth_data = {
++	.phy_irq_pin	= AT91_PIN_PB29,
++	.is_rmii	= 0,
++};
++
++static struct mtd_partition __initdata chub_nand_partition[] = {
++	{
++		.name	= "NAND Partition 1",
++		.offset = 0,
++		.size	= MTDPART_SIZ_FULL,
++	},
++};
++
++static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
++{
++	*num_partitions = ARRAY_SIZE(chub_nand_partition);
++	return chub_nand_partition;
++}
++
++static struct at91_nand_data __initdata chub_nand_data = {
++	.ale		= 22,
++	.cle		= 21,
++	.enable_pin	= AT91_PIN_PA27,
++	.partition_info	= nand_partitions,
++};
++
++static struct spi_board_info chub_spi_devices[] = {
++	{	/* DataFlash chip */
++		.modalias	= "mtd_dataflash",
++		.chip_select	= 0,
++		.max_speed_hz	= 15 * 1000 * 1000,
++	},
++};
++
++static void __init chub_board_init(void)
++{
++	/* Serial */
++	at91_add_device_serial();
++	/* I2C */
++	at91_add_device_i2c();
++	/* Ethernet */
++	at91_add_device_eth(&chub_eth_data);
++	/* SPI */
++	at91_add_device_spi(chub_spi_devices, ARRAY_SIZE(chub_spi_devices));
++	/* NAND Flash */
++	at91_add_device_nand(&chub_nand_data);
++	/* Disable write protect for NAND */
++	at91_set_gpio_output(AT91_PIN_PB7, 1);
++	/* Power enable for 3x RS-232 and 1x RS-485 */
++	at91_set_gpio_output(AT91_PIN_PB9, 1);
++	/* Disable write protect for FRAM */
++	at91_set_gpio_output(AT91_PIN_PA21, 1);
++	/* Disable write protect for Dataflash */
++	at91_set_gpio_output(AT91_PIN_PA19, 1);
++}
++
++MACHINE_START(CHUB, "Promwad Chub")
++	/* Maintainer: Ivan Kuten AT Promwad DOT com */
++	.phys_io	= AT91_BASE_SYS,
++	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
++	.boot_params	= AT91_SDRAM_BASE + 0x100,
++	.timer		= &at91rm9200_timer,
++	.map_io		= chub_map_io,
++	.init_irq	= chub_init_irq,
++	.init_machine	= chub_board_init,
++MACHINE_END
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/board-csb337.c linux-2.6.22-rc5.new/arch/arm/mach-at91/board-csb337.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/board-csb337.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/board-csb337.c	2007-07-29 05:23:04.000000000 +0200
+@@ -24,6 +24,7 @@
+ #include <linux/module.h>
+ #include <linux/platform_device.h>
+ #include <linux/spi/spi.h>
++#include <linux/interrupt.h>
+ #include <linux/mtd/physmap.h>
+ 
+ #include <asm/hardware.h>
+@@ -59,6 +60,7 @@
+ 
+ 	/* Setup the LEDs */
+ 	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
++	at91_set_gpio_output(AT91_PIN_PB2, 1);		/* third (unused) LED */
+ 
+ 	/* Setup the serial ports and console */
+ 	at91_init_serial(&csb337_uart_config);
+@@ -149,6 +151,55 @@
+ 	.num_resources	= ARRAY_SIZE(csb_flash_resources),
+ };
+ 
++static struct at91_gpio_led csb337_leds[] = {
++	{
++		.name		= "led0",
++		.gpio		= AT91_PIN_PB0,
++		.trigger	= "heartbeat",
++	},
++	{
++		.name		= "led1",
++		.gpio		= AT91_PIN_PB1,
++		.trigger	= "timer",
++	},
++	{
++		.name		= "led2",
++		.gpio		= AT91_PIN_PB2,
++	}
++};
++
++#if defined(CONFIG_CSB300_WAKE_SW0) || defined(CONFIG_CSB300_WAKE_SW1)
++static irqreturn_t switch_irq_handler(int irq, void *context)
++{
++	return IRQ_HANDLED;
++}
++
++static inline void __init switch_irq_setup(int irq, char *name, unsigned long mode)
++{
++	int res;
++
++	res = request_irq(irq, switch_irq_handler, IRQF_SAMPLE_RANDOM | mode, name, NULL);
++	if (res == 0)
++		enable_irq_wake(irq);
++}
++
++static void __init csb300_switches(void)
++{
++#ifdef CONFIG_CSB300_WAKE_SW0
++	at91_set_A_periph(AT91_PIN_PB29, 1);		/* IRQ0 */
++	switch_irq_setup(AT91RM9200_ID_IRQ0, "csb300_sw0", IRQF_TRIGGER_FALLING);
++#endif
++#ifdef CONFIG_CSB300_WAKE_SW1
++	at91_set_gpio_input(AT91_PIN_PB28, 1);
++	at91_set_deglitch(AT91_PIN_PB28, 1);
++	switch_irq_setup(AT91_PIN_PB28, "csb300_sw1", IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING);
++#endif
++	/* there's also SW2 at PA21, GPIO or TIOA2 */
++}
++#else
++static void __init csb300_switches(void) {}
++#endif
++
+ static void __init csb337_board_init(void)
+ {
+ 	/* Serial */
+@@ -168,8 +219,12 @@
+ 	at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
+ 	/* MMC */
+ 	at91_add_device_mmc(0, &csb337_mmc_data);
++	/* LEDS */
++	at91_gpio_leds(csb337_leds, ARRAY_SIZE(csb337_leds));
+ 	/* NOR flash */
+ 	platform_device_register(&csb_flash);
++	/* Switches on CSB300 */
++	csb300_switches();
+ }
+ 
+ MACHINE_START(CSB337, "Cogent CSB337")
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/board-dk.c linux-2.6.22-rc5.new/arch/arm/mach-at91/board-dk.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/board-dk.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/board-dk.c	2007-07-29 05:23:04.000000000 +0200
+@@ -73,6 +73,185 @@
+ 	at91rm9200_init_interrupts(NULL);
+ }
+ 
++#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
++#include <video/s1d13xxxfb.h>
++#include <asm/arch/ics1523.h>
++
++/* EPSON S1D13806 FB */
++#define AT91_FB_REG_BASE	0x30000000L
++#define AT91_FB_REG_SIZE	0x200
++#define AT91_FB_VMEM_BASE	0x30200000L
++#define AT91_FB_VMEM_SIZE	0x140000L
++
++static void __init dk_init_video(void)
++{
++	/* NWAIT Signal */
++	at91_set_A_periph(AT91_PIN_PC6, 0);
++
++	/* Initialization of the Static Memory Controller for Chip Select 2 */
++	at91_sys_write(AT91_SMC_CSR(2), AT91_SMC_DBW_16			/* 16 bit */
++				| AT91_SMC_WSEN | AT91_SMC_NWS_(4)	/* wait states */
++				| AT91_SMC_TDF_(1)			/* float time */
++	);
++
++	at91_ics1523_init();
++}
++
++/* CRT:    (active)   640x480 60Hz (PCLK=CLKI=25.175MHz)
++   Memory: Embedded SDRAM (MCLK=CLKI3=50.000MHz) (BUSCLK=60.000MHz) */
++static const struct s1d13xxxfb_regval dk_s1dfb_initregs[] = {
++	{S1DREG_MISC,			0x00},	/* Enable Memory/Register select bit */
++	{S1DREG_COM_DISP_MODE,		0x00},	/* disable display output */
++	{S1DREG_GPIO_CNF0,		0x00},
++	{S1DREG_GPIO_CNF1,		0x00},
++	{S1DREG_GPIO_CTL0,		0x08},
++	{S1DREG_GPIO_CTL1,		0x00},
++	{S1DREG_CLK_CNF,		0x01},	/* no divide, MCLK source is CLKI3 0x02*/
++	{S1DREG_LCD_CLK_CNF,		0x00},
++	{S1DREG_CRT_CLK_CNF,		0x00},
++	{S1DREG_MPLUG_CLK_CNF,		0x00},
++	{S1DREG_CPU2MEM_WST_SEL,	0x01},	/* 2*period(MCLK) - 4ns > period(BCLK) */
++	{S1DREG_SDRAM_REF_RATE,		0x03},	/* 32768 <= MCLK <= 50000 (MHz) */
++	{S1DREG_SDRAM_TC0,		0x00},	/* MCLK source freq (MHz): */
++	{S1DREG_SDRAM_TC1,		0x01},	/* 42 <= MCLK <= 50 */
++	{S1DREG_MEM_CNF,		0x80},	/* SDRAM Initialization - needed before mem access */
++	{S1DREG_PANEL_TYPE,		0x25},	/* std TFT 16bit, 8bit SCP format 2, single passive LCD */
++	{S1DREG_MOD_RATE,		0x00},	/* toggle every FPFRAME */
++	{S1DREG_LCD_DISP_HWIDTH,	0x4F},	/* 680 pix */
++	{S1DREG_LCD_NDISP_HPER,		0x12},	/* 152 pix */
++	{S1DREG_TFT_FPLINE_START,	0x01},	/* 13 pix */
++	{S1DREG_TFT_FPLINE_PWIDTH,	0x0B},	/* 96 pix */
++	{S1DREG_LCD_DISP_VHEIGHT0,	0xDF},
++	{S1DREG_LCD_DISP_VHEIGHT1,	0x01},	/* 480 lines */
++	{S1DREG_LCD_NDISP_VPER,		0x2C},	/* 44 lines */
++	{S1DREG_TFT_FPFRAME_START,	0x0A},	/* 10 lines */
++	{S1DREG_TFT_FPFRAME_PWIDTH,	0x01},	/* 2 lines */
++	{S1DREG_LCD_DISP_MODE,		0x05},  /* 16 bpp */
++	{S1DREG_LCD_MISC,		0x00},	/* dithering enabled, dual panel buffer enabled */
++	{S1DREG_LCD_DISP_START0,	0x00},
++	{S1DREG_LCD_DISP_START1,	0xC8},
++	{S1DREG_LCD_DISP_START2,	0x00},
++	{S1DREG_LCD_MEM_OFF0,		0x80},
++	{S1DREG_LCD_MEM_OFF1,		0x02},
++	{S1DREG_LCD_PIX_PAN,		0x00},
++	{S1DREG_LCD_DISP_FIFO_HTC,	0x3B},
++	{S1DREG_LCD_DISP_FIFO_LTC,	0x3C},
++	{S1DREG_CRT_DISP_HWIDTH,	0x4F},	/* 680 pix */
++	{S1DREG_CRT_NDISP_HPER,		0x13},	/* 160 pix */
++	{S1DREG_CRT_HRTC_START,		0x01},	/* 13 pix */
++	{S1DREG_CRT_HRTC_PWIDTH,	0x0B},	/* 96 pix */
++	{S1DREG_CRT_DISP_VHEIGHT0,	0xDF},
++	{S1DREG_CRT_DISP_VHEIGHT1,	0x01},	/* 480 lines */
++	{S1DREG_CRT_NDISP_VPER,		0x2B},	/* 44 lines */
++	{S1DREG_CRT_VRTC_START,		0x09},	/* 10 lines */
++	{S1DREG_CRT_VRTC_PWIDTH,	0x01},	/* 2 lines */
++	{S1DREG_TV_OUT_CTL,		0x10},
++	{S1DREG_CRT_DISP_MODE,		0x05},	/* 16 bpp */
++	{S1DREG_CRT_DISP_START0,	0x00},
++	{S1DREG_CRT_DISP_START1,	0x00},
++	{S1DREG_CRT_DISP_START2,	0x00},
++	{S1DREG_CRT_MEM_OFF0,		0x80},
++	{S1DREG_CRT_MEM_OFF1,		0x02},
++	{S1DREG_CRT_PIX_PAN,		0x00},
++	{S1DREG_CRT_DISP_FIFO_HTC,	0x3B},
++	{S1DREG_CRT_DISP_FIFO_LTC,	0x3C},
++	{S1DREG_LCD_CUR_CTL,		0x00},	/* inactive */
++	{S1DREG_LCD_CUR_START,		0x01},
++	{S1DREG_LCD_CUR_XPOS0,		0x00},
++	{S1DREG_LCD_CUR_XPOS1,		0x00},
++	{S1DREG_LCD_CUR_YPOS0,		0x00},
++	{S1DREG_LCD_CUR_YPOS1,		0x00},
++	{S1DREG_LCD_CUR_BCTL0,		0x00},
++	{S1DREG_LCD_CUR_GCTL0,		0x00},
++	{S1DREG_LCD_CUR_RCTL0,		0x00},
++	{S1DREG_LCD_CUR_BCTL1,		0x1F},
++	{S1DREG_LCD_CUR_GCTL1,		0x3F},
++	{S1DREG_LCD_CUR_RCTL1,		0x1F},
++	{S1DREG_LCD_CUR_FIFO_HTC,	0x00},
++	{S1DREG_CRT_CUR_CTL,		0x00},	/* inactive */
++	{S1DREG_CRT_CUR_START,		0x01},
++	{S1DREG_CRT_CUR_XPOS0,		0x00},
++	{S1DREG_CRT_CUR_XPOS1,		0x00},
++	{S1DREG_CRT_CUR_YPOS0,		0x00},
++	{S1DREG_CRT_CUR_YPOS1,		0x00},
++	{S1DREG_CRT_CUR_BCTL0,		0x00},
++	{S1DREG_CRT_CUR_GCTL0,		0x00},
++	{S1DREG_CRT_CUR_RCTL0,		0x00},
++	{S1DREG_CRT_CUR_BCTL1,		0x1F},
++	{S1DREG_CRT_CUR_GCTL1,		0x3F},
++	{S1DREG_CRT_CUR_RCTL1,		0x1F},
++	{S1DREG_CRT_CUR_FIFO_HTC,	0x00},
++	{S1DREG_BBLT_CTL0,		0x00},
++	{S1DREG_BBLT_CTL0,		0x00},
++	{S1DREG_BBLT_CC_EXP,		0x00},
++	{S1DREG_BBLT_OP,		0x00},
++	{S1DREG_BBLT_SRC_START0,	0x00},
++	{S1DREG_BBLT_SRC_START1,	0x00},
++	{S1DREG_BBLT_SRC_START2,	0x00},
++	{S1DREG_BBLT_DST_START0,	0x00},
++	{S1DREG_BBLT_DST_START1,	0x00},
++	{S1DREG_BBLT_DST_START2,	0x00},
++	{S1DREG_BBLT_MEM_OFF0,		0x00},
++	{S1DREG_BBLT_MEM_OFF1,		0x00},
++	{S1DREG_BBLT_WIDTH0,		0x00},
++	{S1DREG_BBLT_WIDTH1,		0x00},
++	{S1DREG_BBLT_HEIGHT0,		0x00},
++	{S1DREG_BBLT_HEIGHT1,		0x00},
++	{S1DREG_BBLT_BGC0,		0x00},
++	{S1DREG_BBLT_BGC1,		0x00},
++	{S1DREG_BBLT_FGC0,		0x00},
++	{S1DREG_BBLT_FGC1,		0x00},
++	{S1DREG_LKUP_MODE,		0x00},	/* LCD LUT r | LCD and CRT/TV LUT w */
++	{S1DREG_LKUP_ADDR,		0x00},
++	{S1DREG_PS_CNF,			0x00},	/* Power Save disable */
++	{S1DREG_PS_STATUS,		0x02},	/* LCD Panel down, mem up */
++	{S1DREG_CPU2MEM_WDOGT,		0x00},
++	{S1DREG_COM_DISP_MODE,		0x02},	/* enable CRT display output */
++};
++
++static struct s1d13xxxfb_pdata dk_s1dfb_pdata = {
++	.initregs		= dk_s1dfb_initregs,
++	.initregssize		= ARRAY_SIZE(dk_s1dfb_initregs),
++	.platform_init_video	= dk_init_video,
++};
++
++static u64 s1dfb_dmamask = 0xffffffffUL;
++
++static struct resource dk_s1dfb_resource[] = {
++	[0] = {	/* video mem */
++		.name   = "s1d13806 memory",
++		.start  = AT91_FB_VMEM_BASE,
++		.end    = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1,
++		.flags  = IORESOURCE_MEM,
++	},
++	[1] = {	/* video registers */
++		.name   = "s1d13806 registers",
++		.start  = AT91_FB_REG_BASE,
++		.end    = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1,
++		.flags  = IORESOURCE_MEM,
++	},
++};
++
++static struct platform_device dk_s1dfb_device = {
++	.name		= "s1d13806fb",
++	.id		= -1,
++	.dev		= {
++			.dma_mask		= &s1dfb_dmamask,
++			.coherent_dma_mask	= 0xffffffff,
++			.platform_data		= &dk_s1dfb_pdata,
++	},
++	.resource	= dk_s1dfb_resource,
++	.num_resources	= ARRAY_SIZE(dk_s1dfb_resource),
++};
++
++static void __init dk_add_device_video(void)
++{
++	platform_device_register(&dk_s1dfb_device);
++}
++#else
++static void __init dk_add_device_video(void) {}
++#endif
++
+ static struct at91_eth_data __initdata dk_eth_data = {
+ 	.phy_irq_pin	= AT91_PIN_PC4,
+ 	.is_rmii	= 1,
+@@ -151,7 +330,7 @@
+ #define DK_FLASH_SIZE	0x200000
+ 
+ static struct physmap_flash_data dk_flash_data = {
+-	.width	= 2,
++	.width		= 2,
+ };
+ 
+ static struct resource dk_flash_resource = {
+@@ -170,6 +349,13 @@
+ 	.num_resources	= 1,
+ };
+ 
++static struct at91_gpio_led dk_leds[] = {
++	{
++		.name		= "led0",
++		.gpio		= AT91_PIN_PB2,
++		.trigger	= "timer",
++	}
++};
+ 
+ static void __init dk_board_init(void)
+ {
+@@ -200,8 +386,10 @@
+ 	at91_add_device_nand(&dk_nand_data);
+ 	/* NOR Flash */
+ 	platform_device_register(&dk_flash);
++	/* LEDs */
++	at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
+ 	/* VGA */
+-//	dk_add_device_video();
++	dk_add_device_video();
+ }
+ 
+ MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
+diff -urN linux-2.6.22-rc5/arch/arm/mach-at91/board-ek.c linux-2.6.22-rc5.new/arch/arm/mach-at91/board-ek.c
+--- linux-2.6.22-rc5/arch/arm/mach-at91/board-ek.c	2007-06-17 04:09:12.000000000 +0200
++++ linux-2.6.22-rc5.new/arch/arm/mach-at91/board-ek.c	2007-07-29 05:23:04.000000000 +0200
+@@ -73,6 +73,187 @@
+ 	at91rm9200_init_interrupts(NULL);
+ }
+ 
++#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
++#include <video/s1d13xxxfb.h>
++#include <asm/arch/ics1523.h>
++
++/* EPSON S1D13806 FB */
++#define AT91_FB_REG_BASE	0x40000000L
++#define	AT91_FB_REG_SIZE	0x200
++#define AT91_FB_VMEM_BASE	0x40200000L
++#define AT91_FB_VMEM_SIZE	0x140000L
++
++static void __init ek_init_video(void)
++{
++	/* NWAIT Signal */
++	at91_set_A_periph(AT91_PIN_PC6, 0);
++
++	/* Initialization of the Static Memory Controller for Chip Select 3 */
++	at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_DBW_16			/* 16 bit */
++				| AT91_SMC_WSEN | AT91_SMC_NWS_(5)	/* wait states */
++				| AT91_SMC_TDF_(1)			/* float time */
++	);
++
++	at91_ics1523_init();
++}
++
++/* CRT:    (active)   640x480 60Hz (PCLK=CLKI=25.175MHz)
++   Memory: Embedded SDRAM (MCLK=CLKI3=50.000MHz) (BUSCLK=60.000MHz) */
++static const struct s1d13xxxfb_regval ek_s1dfb_initregs[] = {
++	{S1DREG_MISC,			0x00},	/* Enable Memory/Register select bit */
++	{S1DREG_COM_DISP_MODE,		0x00},	/* disable display output */
++	{S1DREG_GPIO_CNF0,		0xFF},	// 0x00
++	{S1DREG_GPIO_CNF1,		0x1F},	// 0x08
++	{S1DREG_GPIO_CTL0,		0x00},
++	{S1DREG_GPIO_CTL1,		0x00},
++	{S1DREG_CLK_CNF,		0x01},	/* no divide, MCLK source is CLKI3 0x02*/
++	{S1DREG_LCD_CLK_CNF,		0x00},
++	{S1DREG_CRT_CLK_CNF,		0x00},
++	{S1DREG_MPLUG_CLK_CNF,		0x00},
++	{S1DREG_CPU2MEM_WST_SEL,	0x01},	/* 2*period(MCLK) - 4ns > period(BCLK) */
++	{S1DREG_SDRAM_REF_RATE,		0x03},	/* 32768 <= MCLK <= 50000 (MHz) */
++	{S1DREG_SDRAM_TC0,		0x00},	/* MCLK source freq (MHz): */
++	{S1DREG_SDRAM_TC1,		0x01},	/* 42 <= MCLK <= 50 */
++	{S1DREG_MEM_CNF,		0x80},	/* SDRAM Initialization - needed before mem access */
++	{S1DREG_PANEL_TYPE,		0x25},	/* std TFT 16bit, 8bit SCP format 2, single passive LCD */
++	{S1DREG_MOD_RATE,		0x00},	/* toggle every FPFRAME */
++	{S1DREG_LCD_DISP_HWIDTH,	0x4F},	/* 680 pix */
++	{S1DREG_LCD_NDISP_HPER,		0x12},	/* 152 pix */
++	{S1DREG_TFT_FPLINE_START,	0x01},	/* 13 pix */
++	{S1DREG_TFT_FPLINE_PWIDTH,	0x0B},	/* 96 pix */
++	{S1DREG_LCD_DISP_VHEIGHT0,	0xDF},
++	{S1DREG_LCD_DISP_VHEIGHT1,	0x01},	/* 480 lines */
++	{S1DREG_LCD_NDISP_VPER,		0x2C},	/* 44 lines */
++	{S1DREG_TFT_FPFRAME_START,	0x0A},	/* 10 lines */
++	{S1DREG_TFT_FPFRAME_PWIDTH,	0x01},	/* 2 lines */
++	{S1DREG_LCD_DISP_MODE,		0x05},  /* 16 bpp */
++	{S1DREG_LCD_MISC,		0x00},	/* dithering enabled, dual panel buffer enabled */
++	{S1DREG_LCD_DISP_START0,	0x00},
++	{S1DREG_LCD_DISP_START1,	0xC8},
++	{S1DREG_LCD_DISP_START2,	0x00},
++	{S1DREG_LCD_MEM_OFF0,		0x80},
++	{S1DREG_LCD_MEM_OFF1,		0x02},
++	{S1DREG_LCD_PIX_PAN,		0x00},
++	{S1DREG_LCD_DISP_FIFO_HTC,	0x3B},
++	{S1DREG_LCD_DISP_FIFO_LTC,	0x3C},
++	{S1DREG_CRT_DISP_HWIDTH,	0x4F},	/* 680 pix */
++	{S1DREG_CRT_NDISP_HPER,		0x13},	/* 160 pix */
++	{S1DREG_CRT_HRTC_START,		0x01},	/* 13 pix */
++	{S1DREG_CRT_HRTC_PWIDTH,	0x0B},	/* 96 pix */
++	{S1DREG_CRT_DISP_VHEIGHT0,	0xDF},
++	{S1DREG_CRT_DISP_VHEIGHT1,	0x01},	/* 480 lines */
++	{S1DREG_CRT_NDISP_VPER,		0x2B},	/* 44 lines */
++	{S1DREG_CRT_VRTC_START,		0x09},	/* 10 lines */
++	{S1DREG_CRT_VRTC_PWIDTH,	0x01},	/* 2 lines */
++	{S1DREG_TV_OUT_CTL,		0x10},
++	{0x005E,			0x9F},
++	{0x005F,			0x00},
++	{S1DREG_CRT_DISP_MODE,		0x05},	/* 16 bpp */
++	{S1DREG_CRT_DISP_START0,	0x00},
++	{S1DREG_CRT_DISP_START1,	0x00},
++	{S1DREG_CRT_DISP_START2,	0x00},
++	{S1DREG_CRT_MEM_OFF0,		0x80},
++	{S1DREG_CRT_MEM_OFF1,		0x02},
++	{S1DREG_CRT_PIX_PAN,		0x00},
++	{S1DREG_CRT_DISP_FIFO_HTC,	0x3B},
++	{S1DREG_CRT_DISP_FIFO_LTC,	0x3C},
++	{S1DREG_LCD_CUR_CTL,		0x00},	/* inactive */
++	{S1DREG_LCD_CUR_START,		0x01},
++	{S1DREG_LCD_CUR_XPOS0,		0x00},
++	{S1DREG_LCD_CUR_XPOS1,		0x00},
++	{S1DREG_LCD_CUR_YPOS0,		0x00},
++	{S1DREG_LCD_CUR_YPOS1,		0x00},
++	{S1DREG_LCD_CUR_BCTL0,		0x00},
++	{S1DREG_LCD_CUR_GCTL0,		0x00},
++	{S1DREG_LCD_CUR_RCTL0,		0x00},
++	{S1DREG_LCD_CUR_BCTL1,		0x1F},
++	{S1DREG_LCD_CUR_GCTL1,		0x3F},
++	{S1DREG_LCD_CUR_RCTL1,		0x1F},
++	{S1DREG_LCD_CUR_FIFO_HTC,	0x00},
++	{S1DREG_CRT_CUR_CTL,		0x00},	/* inactive */
++	{S1DREG_CRT_CUR_START,		0x01},
++	{S1DREG_CRT_CUR_XPOS0,		0x00},
++	{S1DREG_CRT_CUR_XPOS1,		0x00},
++	{S1DREG_CRT_CUR_YPOS0,		0x00},
++	{S1DREG_CRT_CUR_YPOS1,		0x00},
++	{S1DREG_CRT_CUR_BCTL0,		0x00},
++	{S1DREG_CRT_CUR_GCTL0,		0x00},
++	{S1DREG_CRT_CUR_RCTL0,		0x00},
++	{S1DREG_CRT_CUR_BCTL1,		0x1F},
++	{S1DREG_CRT_CUR_GCTL1,		0x3F},
++	{S1DREG_CRT_CUR_RCTL1,		0x1F},
++	{S1DREG_CRT_CUR_FIFO_HTC,	0x00},
++	{S1DREG_BBLT_CTL0,		0x00},
++	{S1DREG_BBLT_CTL0,		0x00},
++	{S1DREG_BBLT_CC_EXP,		0x00},
++	{S1DREG_BBLT_OP,		0x00},
++	{S1DREG_BBLT_SRC_START0,	0x00},
++	{S1DREG_BBLT_SRC_START1,	0x00},
++	{S1DREG_BBLT_SRC_START2,	0x00},
++	{S1DREG_BBLT_DST_START0,	0x00},
++	{S1DREG_BBLT_DST_START1,	0x00},
++	{S1DREG_BBLT_DST_START2,	0x00},
++	{S1DREG_BBLT_MEM_OFF0,		0x00},
++	{S1DREG_BBLT_MEM_OFF1,		0x00},
++	{S1DREG_BBLT_WIDTH0,		0x00},
++	{S1DREG_BBLT_WIDTH1,		0x00},
++	{S1DREG_BBLT_HEIGHT0,		0x00},
++	{S1DREG_BBLT_HEIGHT1,		0x00},
++	{S1DREG_BBLT_BGC0,		0x00},
++	{S1DREG_BBLT_BGC1,		0x00},
++	{S1DREG_BBLT_FGC0,		0x00},
++	{S1DREG_BBLT_FGC1,		0x00},
++	{S1DREG_LKUP_MODE,		0x00},	/* LCD LUT r | LCD and CRT/TV LUT w */
++	{S1DREG_LKUP_ADDR,		0x00},
++	{S1DREG_PS_CNF,			0x10},	/* Power Save disable */
++	{S1DREG_PS_STATUS,		0x02},	/* LCD Panel down, mem up */
++	{S1DREG_CPU2MEM_WDOGT,		0x00},
++	{S1DREG_COM_DISP_MODE,		0x02},	/* enable CRT display output */
++};
++
++static struct s1d13xxxfb_pdata ek_s1dfb_pdata = {
++	.initregs		= ek_s1dfb_initregs,
++	.initregssize		= ARRAY_SIZE(ek_s1dfb_initregs),
++	.platform_init_video	= ek_init_video,
++};
++
++static u64 s1dfb_dmamask = 0xffffffffUL;
++
++static struct resource ek_s1dfb_resource[] = {
++	[0] = {	/* video mem */
++		.name   = "s1d13806 memory",
++		.start  = AT91_FB_VMEM_BASE,
++		.end    = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1,
++		.flags  = IORESOURCE_MEM,
++	},
++	[1] = {	/* video registers */
++		.name   = "s1d13806 registers",
++		.start  = AT91_FB_REG_BASE,
++		.end    = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1,
++		.flags  = IORESOURCE_MEM,
++	},
++};
++
++static struct platform_device ek_s1dfb_device = {
++	.name		= "s1d13806fb",
++	.id		= -1,
++	.dev		= {
++			.dma_mask		= &s1dfb_dmamask,
++			.coherent_dma_mask	= 0xffffffff,
++			.platform_data		= &ek_s1dfb_pdata,
++	},
++	.resource	= ek_s1dfb_resource,
++	.num_resources	= ARRAY_SIZE(ek_s1dfb_resource),
++};
++
++static void __init ek_add_device_video(void)
++{
++	platform_device_register(&ek_s1dfb_device);
++}
++#else